Having problems with your Toyota Land Cruiser ?

How to adjust master cylinder push rod fj60 landcruiser

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Toyota Land Cruiser

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to adjust master cylinder push rod fj60 landcruiser


... Toyota Land Cruiser

I have a 1992 Plymouth Voyager with a 3.3 liter engine. I have replaced both the master cylinder and brake booster with new parts. The system has been bled about four times. The push rod for the master cylinder has been adjusted. There is no free-play in the push rods. There is no load-leveling device attached to the rear brake system. There is no problem with the way the vehicle stops. It does not pull or jerks. It stops smoothly in a straight line. My concern is that I feel there is exce


The pedal height is adjusted by the rear brake shoes, if the pedal is to low and there is no air in the system then you need to adjust the rear brake shoes.\015\012\015\012let me know if ... Plymouth Voyager

A new clutch, slave cylinder, and clutch master cylinder were all installed but when i push the clutch pedal down it still doesnt engage the clutch all the way, it acts like it is getting a little pressure but not enough to engage it all the way, the adjusting rod on the master cylinder is out all the way, i dont know what to do now?


Have you checked that the slave cylinder is attached firmly where it's supposed to be? Have you refilled the bowl of the master cylinder with braking fluid? And finally have you bled the circuit thoroughly after that? ... 1994 Eagle Talon

I noticed there is threaded adjustment on the clutch pedal push rod going into the clutch's master cylinder hydraulic system. Is this one way I can adjust the hydraulic clutch on my 1998 suzuki sidekick 4X4?


Yes, if you need a little oomph out of the pedal, you can get a little more throw out of the adj rod, or you can get a little less, it doesn't take much to move a clutch. Depends on what the clutch is doing, chattering, slipping, grinding, not shifti ... 1998 Suzuki Sidekick

On a 1966 ford galaxy with drum brakes all around, is there some sort of washer that goes between the push rod from the brake booster to master cylinder internal guts! All I did was take it apart to sand blast the parts for paint and now its as if the push rod doesn't make contact with the cylinder! And I did not change the length of the push rod!!!


I WOULD REPLACE IT.WHICH WILL BE MORE SAFER.SO YOU WONT HAVE BRAKE FAILURE. ... 1966 Ford Mustang

Brake Master Cylinder Push Rod Clearance


No Adjustment.Rod is made into booster,there's a short rod between master cyclinder and booster but not adjustable!! ... 1999 Saturn SL

Push rod I am curious to know what the cost may be for a push rod? My girlfriend just spent $400 to get the master cylinder replaced and is now being told she needs a new push rod.


... Ford Escape

May 16, 2010 - What I am having problems with is my 98 ford ranger, 4X4 3.0, if the ccp switch that is on the push rod for the master cylinder slides up and down the shaft, cannot get it to secure to the master cylinder. I ve just had a new clutch, throw out bearing , pressure plate , slave cylinder replaced about 4 months ago. I was driving down the road yesterday and suddenly had no clutch. Played around with the ccp switch and the clutch started working just fine again. Now I have to stop an


Clutch Pedal Position Switch = CPP switchThe Clutch Pedal Position (CPP) switch is an input to the PCM indicating the clutch pedal position and, in some manual transmission applications, both the clutch pedal engagement position and the gear ... 1998 Ford Ranger SuperCab

On solution #1 dec 2008 I would like to know where i could get the adjustable clutch master rod between the master cylinder and the clutch pedal. He mentioned it could be purchased on line but did not say where. My clutch pedal does not come back to its stop even with the brake pedal. The slave cylinder is new the old one was corroded. It appears the slave cylinder was replaced and I bled the line but could not get enough travel to releace the clutch. Looking at the clutch pedal travel I tried t


After reading this I have to ask if parts are origional why do they not work properly. My first suggestion is that bleading not done effectively. If air is present in line,slave cylender etc. then it would not have travel needed or master cylinder is ... 1984 Pontiac Fiero

The cantilever system that you mention on the sanderson consists of a metal bar with three holes in. The centre one of which attaches to the brake pedal but is not fixed and allowed to rotate. The two push rods from the master cylinders attach to each end of the bar. On depressing the pedal the rods enter the cylinders but one goes in farther than the other as they seem to counteract one another. Does this sound familiar?


... 1985 Mitsubishi Pickup

I have replaced the brake master cylinder and bled the brakes. I still have spongy feel to them and it also feels as if the push rod is off, but it isn't at least not at the master cylinder.


You will have to bench bleed the new master brake cylinder. you can buy a kit the contains fittings and hoses to do this on the car. When you install a new master brake cylinder without bench bleeding it first air will remain trapped inside and n ... 1988 Dodge Dakota

Changed master cylinder after push rod snapped. Won't go into gear. Then changed slave cylinder ( on a new slave cylinder do you do anything with that plastic piece or leave it alone?) Still won't go into gear. Familiar with bleeding lines but not sure if doin it right ? thank you anna


It verifies if the auxiliary cylinder opens completely if this one does not open it is because the principal cylinder has air ... Chevrolet S 10

Clutch problems I can't shift into gear, I replaced the plate and throw out bearing, it seems like there should be longer push rod from the clutch master cylinder to the throw out bearing. I've replace the clutch master to no avail...


... 1966 Triumph Spitfire

The eyelet on my clutch master cylinder broke in half.I think the mastre cylinder is ok,can I just replace the push rod? The intire clutch is only a year old.93 f150 300 6cyl.thanks . The eyelet I refer to is the end of the pushrod that connects to theclutch peddal linkage.


... 1993 Ford F150 SuperCab

96 e350 replaced master cylinder and proportioning valve,brakes will slowly go to floor as pressure is applied. could booster be bad or rod through booster to master be out of adjustment ??


Probably bad or air in the lines ?? try bleeding them first ??? ... 1995 Ford F250

My '78 mercedes had a leaky master cylinder, it leaked into the vac. boost. I replaced it, but now it has no pedal play and when pumped a couple times it seems to keep brakes on a little. Is there an adjustment? The rod seems to not have adjustment.


Hi,\015\012 You have air in your brake lines. Get that taken care of, you don't want to slam on your breaks in an emergency to have a pedal go to the floor.\015\012 I think Walmart sells a brake bleeding kit, though I've never used one. ... 1990 Mercedes-Benz 300 Diesel

Pics of adjusting rod in master cylinder on 2008 expedition


... 2008 Ford Expedition

Adjust rod from booster to master cylinder - 1999 Chrysler Town & Country


... 1999 Chrysler Town & Country

Pics of adjusting rod in master cylinder on 2008 expedition


... 2008 Ford Expedition

How do you adjust an abs module. when replacing the master cylinder, the abs gears were turned. when it was put back, the pedal is very stiff and needs to be pushed on very hard to stop. there is not much travel in the pedal.


... 1996 Oldsmobile Cutlass Supreme Coupe

Is it fairly easy to install a clutch master cylinder (1994 gmc sierra 2500)my main concern is disconnecting and reconnecting the push rod to the clutch pedal through the little hole in the fire wall is is the connection back in pretty far / thanks for your help or suggestions .


It is very easy to replace the parts, bleeding the air is the real problem, u will need to buy a Mityvac brand vacuum clutch bleeding tool, with out it you will never get the air out of the system after the parts are replaced, also always replace the ... 1994 GMC Sierra

Is there a push rod adjustment for the brake master on a 1989 prelude?


Nope ... 1989 Honda Prelude

1997 GMC C1500 pickup 2-wheel drive. Brake pedal has too much freeplay in it. I have replaced all the shoes/pads and rotors and drums and also the master cylinder. I am not sure how to take out the freeplay in the brake pedal. I am assuming the pedal can be adjusted by way of the pushrod that pushes on the booster but I would like to sure before I dig into it. Thank You!!!


If you still have that much play you may have to replace the booster as well. If you go to changing the pushrod it may add too much pressure to the booster and make it fail. ... GMC C1500

I have an 1989 Toyota Camry 2.0 liter 4 cylinder manual and I'm experiencing lack of free play with the clutch. I keep adjusting the locknut but today i couldn't reach 40 mph. At one point i was losing speed. When i opened the hood smoke came out from the bottom where the clutch push rod is. I smelt oil burning off of it. I believe that i have an oil leak but don't understand how that would affect my clutch and speed. What should i mainly be looking at transmission, a clutch issue or just an oil


It might be your rear seal on the engine block leaking,there should be a metal plate on the bottom of the bell housing of the tranny u could take off and might be able to tell something ... 1989 Toyota Camry

Rover (a Honda Rover) 416SLi 1994, master cylinder replaced, brakes not coming on fully. Is there a ball bearing or short rod between the booster pushrod inside the the cylinder operating tube ? I may have dropped it when I disassembled the old master cylinder. The master cylinder is a Honda item.


There should be one rod between the master,and the booster.If the brakes where bled,at the master,and at each wheel,then if it has rear brake shoes,they are worn out,or need adjusting,if indeed your brake pedal is not a full pedal,I think that is wha ... Honda Prelude
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.2258 seconds