Having problems with your Toyota Land Cruiser ?

Toyota landcruiser HZJ80 1993 1HZ engine. I am removing the main diesel fuel pump and I have it at the stage that its nearly off. The drive shaft that enters the timing cover will not pull through. I have the timing belt and drive pulley off, and the front nut on the fuel pump drive shaft is off, but cannot get the pump off..

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

The front drive gear is on with a slight press fit, you will need to use a 2 or 3 jaw puller to pull the front gear from the injection pump, it does not take much to pop it lose. then you will be able to remove the pump.....good luck
Repair Help & Product Troubleshooting for Toyota Land Cruiser

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Toyota landcruiser HZJ80 1993 1HZ engine. I am removing the main diesel fuel pump and I have it at the stage that its nearly off. The drive shaft that enters the timing cover will not pull through. I have the timing belt and drive pulley off, and the front nut on the fuel pump drive shaft is off, but cannot get the pump off..


The front drive gear is on with a slight press fit, you will need to use a 2 or 3 jaw puller to pull the front gear from the injection pump, it does not take much to pop it lose. then you will be able to remove the pump.....good luck ... Toyota Land Cruiser

What would be a reasonable price for the following work and how would I know if these things were actually done? 2003 Audi A6 Transmission filter kit Water pump Timing belt Idler pulley Rear tranmission seal Drive belt (a/c) Drive belt (alternator) Front Rotors Front Pads Left front upper control arm Sparkplugs Cam shaft seals Valve cover gaskets Fuel filter Air filter Oil filter Engine oil Transmission oil Engine Coolant


It is VERY unlikely that a seven year old car would need that much done to it, unless it had 200,000 or more miles on it. New oil should be the color of honey, not dark brown. That's the easy check. ... 2003 Audi A6

I have a 2000 GMC Sierra, if I cannot hear the whirring sound of the fuel pump when the ignition is in the "on" position, would it be safe to assume that the fuel pump has failed? I was driving down the road and in the space of a few minutes my truck began to **** as if it was running out of gas, however I had 3/4 tank. Up until the day the truck died I had NO problem whatsoever with fuel starvation. I have never heard of a fuel pump going bad in such a short span of time. I have checked all fus


The fuel pump should only run for 2 seconds after the ignition is turned on unless the vehicle starts. Have someone lean under the truck while you turn on the ignition, you only have 2 seconds to hear it then you have to turn the ignition off again ... 2000 GMC Sierra

Engine cranks, but won't start. Car has gas-Confirmed. Air Filter clean. Problem developed over several days. (i.e. harder & harder to start each day.) No problem noticed in engine/vehicle performance while driving, or engine idling, during this time frame. I had changed the fuel pump & filter a few years ago (3-5 years ago pump failed.) I usually can hear the fuel pump run for a few sec.s when I turn the key on, but cannot hear it now. Have not checked fuses for pump yet, but would like to thin


Test replace the fuel pump relay, make sure the relay socket has 12 volts to 2 of it's terminal when the key is held in crank position, if not you may have a defective ignition switch or Powertrain control module (PCM) ... 1994 Plymouth Voyager

With my bmw318i 1997.i have difficulty starting hot or cold.the only way i can start is turn key on wait for about 30 seconds then start 70% time will start. if i turn the key fully straight away no chance .had new fuel pump,and filter starter moter cam shaft sensor all by bmw specialists and still have problem.when started initialy gives the effect of flooded coughing but car drives good and smooth.the bmw workshop said they replaced the cam shaft sensor 3 times ???


Look for bad grounds in the ignition circuit.the corrosion is creating a voltage drop,but time and heat decrease the resistance.. ... 1997 BMW 318

We have a 2001 Kia Optima. The check engine light came on, the car started losing power while driving and then quit running. The timing belt was going bad. We had it replaced. That did not solve the problem. We had the fuel pump replaced and the cam shaft sensor. Still had the same problem. We can drive it for about 25 miles and the problem starts again. We let it sit for 10 minutes and we can drive another 20 miles before it happens again. When it loses power, it feels like it's down shifting.


Try to replace the ignition coil. Defective ignition coil will stop to function when it gets hot. When it cools down, it will function again. ... 2003 Kia Optima

We have a 2001 Kia Optima. The check engine light came on, the car started losing power while driving and then quit running. The timing belt was going bad. We had it replaced. That did not solve the problem. We had the fuel pump replaced and the cam shaft sensor. Still had the same problem. We can drive it for about 25 miles and the problem starts again. We let it sit for 10 minutes and we can drive another 20 miles before it happens again. When it loses power, it feels like it's down shifting.


You need to find out the error codes being generated when the light came on. These codes will stay in memory until being reset by a code reader. The reader plugs into the OBD II port under the dash, near the steering wheel. (OBD stands for On Board D ... 2003 Kia Optima

I have a 2003 Jeep GrandCherokee which has had the cam shaft, crank sensor, fuel pump, fuel filter, and battery replaced, The transmission has had a fush and fill done. Since then, when I proceed to crank the car up, it takes three trys before the car ignites with the battery; (By the way, the starter and alternator both have been replaced- twice), when the car ignites and I start to drive, once the car gets up to 45 mphs or higher, the car sputters, often time it stalls, the gauges start jumpi


Hi!\015\012\015\012Questions:\015\012\015\012When did you started having this problem with your vehicle?? What was changed before and after the problem started? The tune up was performed after the problem started? \015\012\015\0 ... 2003 Jeep Grand Cherokee

I have a 2000 Chevy Blazer 4 dr 4 Wheel Drive with the 4.3L Engine. A couple days ago the kids went to use it and it would not start. Well it starts but shuts off a second later each time you turn key. Also the same time all dome lights do not work and the door lock button on driver door will only lock all doors and only unlock all doors except driver door. Also security light stays on solid (no blink) weather key is on or off. Cannot reset security system at all. Checked fuel pump pressure on f


... 2000 Chevrolet Blazer

During the summer time it will cut off sounds like it is loosing fuel pressure will turn over, but wont start back up until at least an hour later. Drives perfect during the winter time no problems, replaced the ignition coil and ignition module several times, distributor pick up, fuel pump twice, fuel fiter, emergency fuel pump cutoff, fuel pump relay, spark plugs, plug wires twice, checked the fuel pressure on the fuel rail, it puts out 40 psi on idle and does not go below 25 until you shut it


What causes this is ussually the oxygen sensor. It works when the engine heats up and if its no good, it will run your engine lean or even shut it down. check them and replace them. They should be done every 2 years. ... 1991 Mercury Topaz 4 Door

2000 mercury grand marquis 4.6 Intermittent problem. 35,000. miles. Problem engine died several times wile driving. Also after car is parked from a drive will not start. Found that the fuel pump is not turning on with the ignition key turned on after car was parked. Checked for fuel pressure ...no pressure. Suspect that fuel pump is not on when cart dies when driving. #1 1st Tested car when car was working good and problem was not there. .Fuel pump fuse good. Fuel pressure good 35psi Tested F


... Ford Cars & Trucks

My L300 4x4 Starwagon surges on occasion when driving. I Changed the fuel filter, cleaned out the tank, & checked fuel lines, & changed fuel suppliers several times but it still persists. I've had the pressure checked 3 times & each time comes up good. I suspect the fuel pump is on the way out but I can't spend $200 Aus to find out. Any suggestions about the surging cause? Is there an electric alternative pump that can be fitted outside the tank? Something like the old SU pumps fitted to the Mor


... 1990 Mitsubishi Minivan

Fuel i have a 1989 buick regal i have changed fuel filter, pump, spark plugs.the car wont start sometimes when i turn it off, it stop twice while driving i pulled over and cranked it a few times and it started or i would have to let it sit for a few min when it stop the car was still on it was like it was out of gas but there was plenty. i also wanted to tell you i changed the fuel pump 2 times could it be the fuel pump relay or is it something else?


Try ignition module go to this site to show you how.\015\012\015\012mhttp://www.autozone.com/shopping/repairGuide.htm?\015\012pageId=0900c15280067bbc ... 1989 Buick Electra

I have a 03 stratus rt it started missin real bad one day while driving i changed valve cover gaskets cuz there was oil gettin into my plugs an thought that would solve the problem but didnt. i took the car home an parked it for the night the next day it would not start it would turn but not fire u could smell the gas an all so it was gettin that. i replaced the plugs wires dist cap rotor fuel pump cleaned all the sensors an checked them an still nothing. somehow the timing got messed up so i fi


... 2003 Dodge Stratus

My 1991 oldsmobile eighty eight royale keeps dying when i drive it, I have replaced ing control moduel, fuel pump, mass air flow , cam shaft sensor, timing chain, plugs wires ect. do i need to keep going???


With that much already invested, why give up now? How about the crank position sensor-was that replaced as well? For spark control and spark timing, the computer needs inputs from both the cam position sensor and the crank position sensor before it ... Cars & Trucks

The car just cuts off whiling driving.. fast,slow. Sometimes it will start up again if you are coasting because you were drinving at a high speed when it cuts off. Other times it cuts off and you can turn key off and wait about 1 or 2 mins and it starts uo right away. IT seems to only happen after serval 100 miles sometimes more. I replaced fuel pump already. Please help cannot figure it out.


Thanks for choosing FixYa and welcome to the site. Do you have a check engine light on? How long has it been since the last tune up? You may need a map sensor or it may be in the ignition system. Have you checked your fuel pressure? ... Mercedes-Benz E-Class

Timing engine g,day got an l300 express van (4wd).it has a 2.4l eci engine.had low eng oil press so removed timing cover to make sure oil pump belt was not damaged(was told oil pump runs from different belt to cam,found out later that its actually balance shaft that has its own belt)after reassembling eng. it would not start.had plenty of spark.once again removed timing cover to make sure i hadn't disturbed timing even though timing belt wasnt touched.appeared that when crank was to timing mark


I had a 2.4 L engine in a caravan and replace the water pump that was controlled by the timing belt. \015\012I was having the same problem, I called my bother in law to help. The crank shaft has to stay perfectly timing on the low end. The cam ... Mitsubishi Diamante

I am replacing the water pump on my 1996 Isuzu Rodeo. One of the water pump bolts is under the lower timing belt cover. However, the lower timing belt cover appears to connect around the crank shaft behind the three lower pulleys. How do I remove the pulleys so that I can remove the lower timing belt cover? What size and type wrench should I use? Thanks, Ralph


Hello Ralph,\012\012What you actually going to have to do is take both timings covers off eventually. The waterpump is driven by the timing belt, and will have to be removed along with various other components. \012\012The pul ... 1996 Isuzu Rodeo

FUEL PUMP We have a 2000 E320 4 Matic. no consistancy, but sometimes while either driving,the car will stop running,sometimes restarts within 20 min. but last time, we even let the car sit for 2 days and it still won't start. 3 times now, we have driven the car to work,let sit for 3-4 hours and then won't restart? let sit overnight and restarts ok... We don't hear the fuel pump when ignition is on, when we spray starting fluid into the intake the car starts but won't staty running??? Fuel Pump??


Hello,maybe fuel pump,, or your k-40 relay module(fuel pump relay)better to install a fuel gauge to determine, fuel pump or your fuel pump relay,ty ... 1999 Mercedes-Benz E-Class

Hi, my 97 chevy truck has intermittent problems. It runs fine most of the time but sometimes it wont start and the fuel pump wont kick in. But then a few minutes later when I try it, it runs. Sometimes when im driving it will all of a sudden just quit and then fire up as im still in motion. it will do that a couple of times and then die. so then i'll pull over to the side of the road and check things out. tap on my fuel pump relay sometimes or disconnect the wire harness to the fuel pump and rec


You need to have a fuel pressure gauge to check it when it wont run. Take your fuel pump relay and switch it for the horn relay. Is the ground good for the fuel pump, the wire bolts on the frame. these had problems with the connector at the fuel tank ... Chevrolet 1500

MY 2003 FORD EXPEDTION STARTS UP YOU DRIVE FOR AWHILE AND IT DIES SOMETIMES IT STARTS RIGHT UP SOMETIMES IT TAKES THREE OR FOUR TIMES. FINALLY IT WOULDN'T START BOUGHT AND INSTALLED A NEW FUEL PUMP STILL WONT START HOOKED MY OLD FUEL PUMP UP TO A BATTERY PUMPS FUEL. CHECKED PULG WHERE FUEL PUMP PLUGS IN TO MAKE SURE I HAVE PROPER VOLTAGE AND IT DOES SOON AS YOU PLUG FUEL PUMP IN VOLTAGE IS LOST. THOUGHT IT WAS A GROUND ISSUE GROUNDED RIGHT TO THE FRAME AT THE PUMP STILL WONT HAVE PROPER VOLTAGE.


Had a similar problem was the air intake idle control motor ... 2003 Ford Expedition

I have a 92 chevy s10 blazer 4x4 4.3 vortec W i just replaced the fuel pump and fuel filter.. it will start sometimes mainly after it sits overnight but when you drive it you can only drive for about 10 mins and it will chug the whole time and then shutoff... i was told it could be the fuel pump relay or the fuel pressure regulator and was wondering what to try first?


I had this problem.I removed the fuel pressure regulator and it was full of carbon.Remove it very carefully as to not damage any seals.Remove as much carbon as you can and reinstall.This should solve your problem. ... 1992 Chevrolet S-10 Blazer

Three codes p1670,p0171,andp0174 . p1670 main computer cannot find the a.b.s. computer. I do not think this code alone would bring the check engine light on. But p0171 and p0174 which are engine too lean bank 1 and bank 2 will bring the check engine light on. Took to dealer three times: 1st time they said they found a leaking vacuum canister and two vacuum hoses. It cost me $87. Same codes came back. 2nd time they said fuel pump was insufficient flow. They replaced fuel pump under warranty. Same


Did you or someone in your family TOP OFF the gas tank?\015\012\015\012It's a bad habit that's hard to break.\015\012\015\012====\015\012\015\012The vacuum canister can be soak with gasoline.\015\012\015\012The only inexpensiv ... 2004 Suzuki Verona

When driving or sitting ticking over the car will suddenly stop,it puts on the auto gearbox light. the car will start again after a short while i have replaced the crank sensor , fuel pump all to no avail. the last time i had no spark at the plugs, i again replaced the crank sensor, she started first time,however after a few minutes she stopped, after checking the fuel pressure in the engine rail which showed 2 bar i was advised to change the pump which i have, the new pump shows 2 bar and all t


Hi I think your problem is connected with your Air mass meter if you look at your engine from the n/side it is situated just after the air filter box it has a spring clip at one end a flat metal thin box with a lead attached and a jubilee clip at the ... 1997 Jaguar XJ6

I have a 2000 Galant 2.4 sohc. car dies on road i took off timing covers balance shaft was broke and timing off. change belts used haynes manual to make sure i did it rite. i line the oil pump drivin balance shaft up by putting a screwdriver in plug hole in side of block and line up marks. I did that but when i turn the crank 2 times and check to make sure its lined up everything is ok but the oil pump sprocket is way off why?


See picture below:\015\012 ... Mitsubishi Galant
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.2226 seconds