Having problems with your Mitsubishi Lancer ?

What ignition timing should an evo 3 4g63 be set to?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Mitsubishi Lancer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What ignition timing should an evo 3 4g63 be set to?


... Mitsubishi Lancer

I cant get timing set correct on my chevy truck it it 93 1500 4wheel drivewith 4.3 v6 i have replaced ignition coil plug wires and tps and fuel filter ignition module cap and rotor cant read degree marks on timing tab i had the timing chain checked by a local machanic he says there is a small amount of play but it does not to be replaced the engine code is z it the engin id says zero degrees timing i think the computer is working against me how do i return it to base time so i can set the timin


You can take a yellow chalk marker to the timing mark on the balancer and make it stand out. You then clean off the template on the block that has the marks. If you cannot use the timing marks then you can use a vacuum guage on the intake main vacuum ... 1993 Chevrolet K1500

When setting ignition timing it says set with rpm at 600 but when setting curb idle it says to set curb idle at 600 in drive so on the ignition timing do you use 600 in neutral or 600 in drive. the veh i a 76 vette 350 auto


600 RPMS IN PARK ... 1972 Chevrolet Corvette

Ignition timing I own a Golf II GTI 2.0 16V and my problem is the ignition timing. I have just installed the new flow meter, new plugs, new air filter, new fuel filter and a new oil filter. But the problem I am experiecinf is that the ignition is bad. when I start the car it takes time to catch on and when it finally starts it does not hold the iddling after three or four attempts it holds. I need to know how can I set the ignition timing myself.


Use timing light to set correct ignition timing. ... 1992 Volkswagen GTI

The cruise control does not set the speed most of the time. It does set some times after we have been driving a while. Will not set if stop and turn off ignition. Using brake to disconnect will resume with resume button. Tried contact cleaner on set switch. Thank you, Alan


In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering ... 1999 Oldsmobile Aurora

Where is the ignition timing bypass connector on a 1994 Chev. Silverado CK2500? After putting in a new distributor, now trying to set the timing. Need to find the bypass connector in order to override computer and set timing manually. HELP!?!?


I think 94 is still OBD1 computer system. Have you ever run codes on it? If so the diagnostics terminal will over ride the computer when running so you can set timing. Just get a .99 cent code key from Autozone or use a paperclip. ... 1994 Chevrolet C2500

Hi I have a 03 BMW 320d I have a problem where every time I turn off the ignition the time clock resets and displays --:-- this happens even when I set the correct time. Also the short trip milage counter resets to zero when I turn off the ignition aswell. Any advice thanks?


Disconnect battery mate and connect again this should work i had same problem. ... 2003 BMW 325

I have a 1982 Dodge Ramcharger 4x4 318 2bbl.I am looking for the proper ignition timing settings.It starts good and idles well.It has a new carter carb on it,new spark plugs,cap and wires,rotor button and new timing chain.When we set th etiming at 2 BTDC it pings when you step on the gas at any speed,then when you road set it and stop the pinging,it will hardly pull itself.What should it set at to work properly as its harder than usual on gas...


Well we knoe the problem bet what are u having problems with starting the car????? ... 1990 Dodge W150

Torque Settings I need torque settings for 1980 mazda 323 ohc 4 cylinder inline timing chain driven, torque settings for cylinder head,main bearings,big ends,flywheel, valve clearances (hot & cold) ,ignition timing. please


... 1980 Mazda 323 1.5

I have a 1998 Hyundai Accentb 1.3 XS and would like to set the ignition timiong with a timing light, but do not know how many degrees before or after TDC the timing must be set. Please advise. Dave.


... Hyundai Motor 1998 Accent

Setting up ignition timing on 205 1.6 gti with a timing gun what should i set it at and the the rpm?


... 2005 Peugeot 405

Ignition Timing How do I set ignition timing on a Suzuki X90?


What year.?http://www.kick-fix.com/following link, see 16v timing.same. ... Suzuki X-90

How do i set the timing on my 94 geo tracker and do you set it up on #1 or #2,#3,#4 replaced timing belt but want fire up,has spark but know ignition


Always cyl 1 \0128 at 800 rpm ... 1994 Geo Tracker

I just bought a 95 olds aurora. The ignition will start the car about 50% of the time & says to clean the key & try again in 3 minutes the rest of the time. The battery will go dead if left to set for several hours. I've tried replacing the ignition switch. but still have the problem. The key will only go to the off position & not all the way to the accessory position.


I hope you have the master key!!! send it to the vehicle dealer and have them cut a copy for you !!! you will need it... \\before you do that try changing your battery.. ... Oldsmobile Aurora

Hello i wanted to know the ignition timing advance specifications for my Honda Civic LX1.5 (philippines) with a D15B3 engine (carb). I wanted to know what is the specificition for the initial advance and the total advance (with vacuum hose disconnected). also i normally just use a timing light to check on the timing and with vacuum hose connected i set it where the timing marks (the three notches on the crank pulley) is centered on the timing mark pointer on the lower timing belt cover. These


... Cars & Trucks

Timing, 89 GMC Ignition timing connector. I disconnected my timing bypass connector. to time my truck. Set Timing to 4 degrees btdc. When I reconnected my bypass connector the mark on my damper should have move dramatically, IT DID NOT MOVE AT ALL. what would cause this to happpen?


... 1990 GMC Sierra

IGNITION KEY WILL NOT COME OUT OF IGNITION SWITCH. This is the third time this has happened. The dealer (Vic Alfonso) doesn't seem to be able to fix it or they are fixing the wrong problem. They keep telling me its my key. I don't think it is because it turns the H3 on and off easily, it just won't come out of the ignition switch. The H3 is now setting outside unlocked with the switch in the accessory position.


The next time you do get it out,take the key to any hardwear store that makes key's,have them make a dupe if they have a blank,so you have a copy,then have them run your key on there wire brush to smoth all the sharp edges,if it still sticks, then re ... 2009 Hummer H3

My 62 lincoln runs fairly well for about 10 to 15 minutes and then starts to backfire and lose power to a stallout. Ive replaced the timeing gears and chain, changed the carb and fuel pump and backblew the fuel lines with compressed air. the timeing is set at 10 degree advanced. everything seems to check out ignition wise . if i leave it alone after a stall it will restart in about 2 minutes, not near enough time to cool the engine down. help!


Replace your coil. This happens on these older vehicles a LOT as the oil begins to evaporate out of the ignition coil. My '54 GMC used to LOVE to do this. ... Lincoln Continental

Ignition timing hi i have a 1998 toyota caddy 1300 on the motor it is a e3 stamped whith the engin number i wan to now where is the right timing marks and how do i set the timing on the top poley there ar a 2e and a 3e hole


... Cars & Trucks

Timing I replaced the timing belt along with the spark plugs, ignition switch now i need to know the timing diagram to set it back right.


Be good to know what engine you have !!!!!!!!!!!!might be able to help then ... 1991 Volkswagen Fox

How do i set the ignition timing on a 1999 Honda civic? there is no more room to adjust the timing, I put in a new distributor because of the ignitor went out and I tried to adjust the timing to recommendations but I have no more play.


Go under the steering wheel and cut the red wire and the **** spice it back ... 1999 Honda Civic

Valve clearance for tune up?idle mixture setting?rpm setting?timing and distributor setting?and can i change my distributor to an electronic ignition system?


... 1985 Mitsubishi Cordia

How can I set ignition timing for a 1993 Nissan pickup D21 2.4L


The mark to the right of the pully will be 0 .. it will be like this. 8 6 4 2 0 ... 1993 Nissan Pickup

How to set the ignition timing on a 2002 Mustang


TIMING IS ADJUSTED BY THE ENGINE CONTROL UNIT SO IT SHOULD'NT NEED ADJUSTING.ODDS ARE THAT YOU CAN'T GET RID OF EXHAUST FAST ENOUGH DUE TO A PLUGGED CONVERTER. ... 2002 Ford Mustang

Setting Ignition Timing Audi 100L


... Audi 100
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.1157 seconds