Having problems with your Jeep Cherokee ?

My Jeep will cut out while driving and eventually go dead. After a bunch of restarts it will clear up. I've replaced almost all the sensors. Please help so it will stop

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

You need to test your alternator to see if it is properly charging your battery. Start your jeep and remove the positive connector from the battery. If your vehicle stalls you may need an new alternator. Also check the following issue that could cause you to stall, clogged fuel filter, choke not properly operating, faulty emissions system components, distributor cap damaged or wet, bad spark plug wires, leak in your vacuum system intake manifold or hoses. Also check your spark plugs for wear or improper gapping.
Repair Help & Product Troubleshooting for Jeep Cherokee

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Jeep will cut out while driving and eventually go dead. After a bunch of restarts it will clear up. I've replaced almost all the sensors. Please help so it will stop

You need to test your alternator to see if it is properly charging your battery. Start your jeep and remove the positive connector from the battery. If your vehicle stalls you may need an new alternator. Also check the following issue that could caus ... Jeep Cherokee

My speedometer and odometer stopped working and the transmission shifts out of first really hard into second then wont shift any farther. it will reset itself when i turn the car off but it does the same thing . ive have changed the input and output sensors and autozone was telling me it has a speedometer cable but i can not find one. i have also replaced the gauge cluster and checked all the fuses. what could be the problem. please help im ready to blow the dang thing up

95% for sure its the ignition switch, under steering column, bottom left\015\012 side, east \015\012to replace, but i think needs a torx driver. i had the same problem ... 1996 Dodge Intrepid

I have a 99 chevy my abs light on dash is on once that happens the break ligjt comes on speed gage stops wooking then transmission does not want to go shoft onothing ive checked fuses replaced te speed sensor and the problem has gotten worse now check ingine light is on please HELP

Ok first lets address the abs light. Have you tried to have the codes read?usually an abs light is due to a faulty wheel speed sensor. once that happens with the brake light and speedometer quites working, it sounds like the truck goes into shutdown ... 1999 Chevrolet Silverado 1500

Why do I get almost 4000RPM at 60mph when I used to get 2,750RPM. The overdrive works when I just start the vehicle and run it but when I slow all the way down the overdrive stops working until I shut down the vehicle and started back up. I have replaced new knock sensors so I don't know what the problem could be. Please help.

... 2001 Lexus RX 300

2000 model f-350 7.3 liter deisel, acts like it's missing or not burning the fuel, but if i "stomp it" it'll go! runs just fine, but just normal driving it misses and stops, misses and stops. i've just replaced the cam/crank sensor, didn't help. vechile speed sensor ?? or accel. pedal sensor ?? any help or direction please thanks

My 2001 Ford F-550 7.3 pwrstrke did a similar, and I found the problem to be on that is notorious on the ole 7.3's. The 8th injector get the lowest oil pressure and it feels like a skip. Its in Ford spec, but it actually isn't getting the same pressu ... 2000 Ford F350 Super Duty Super Cab

03 eclipse gs 2.4 auto.Runs rough also if you give it alot of gas it has almost no power and almost stalls but doesnt. I have replaced plugs,wires,coils cam sensor, crank sensor, cleaned throttle body.....also it did have a check engine light on codes p0335 p0340 p0300 after i replaced all those things i cleared the light and it never came back on but still runs rough...i dont know whats left to do!! It was running fine 2 days prior... Then it started and ran rough.please help

Possibly the o2 sensore ... Cars & Trucks

O2 sensor won't stop coming on.. All are replace but the bank2 sensor 2 keeps coming back on.. That sensor was replaced with OEM sensor but it's saying there high voltage as well.. Please help!!

Unplug the suspect sensor and check it for a damaged or bent pin. May ... Cars & Trucks

I have a 2005 nissan frontier, crew cab, nismo edition. my service engline light has been on for about 6 months straight. i have replaced many things and nothing has worked. ive replaced the radiator and surroundings due to tran, fluid and oil leaking into the radiator. ive also replaced one of the catalytic converters. my engine shutters while at speeds areound 40-45mph, and 60-65mph. this only happens with my overdrive ON, when i push my OD off button, it stops. please help

... 2005 Nissan Frontier

Mazda 323 Seems Like It's Flooding Out Mazda 323 1999 1.6 Automatic .Suddenly lose power and engine stopped .It's happened every 20 - 30 minutes. I replaced crank sensor (down), plugs, FUEL pump and Air filter,But same problem appear -- Sometimes the engine stops at a long stop at intersections. Then the car is hard to start again. When i loose power I feel the gaz pedal no effect . To start again the car i should wait 5-8 minutes. (Maybe second crank sensor ?) Please Help. Benn Thx

... 1994 Mazda 323

Hello I have a 1990 chevy lumina euro 4dr 120k..I have had all the sensors replaced, tps sensor and so on the fuel pump and fuel filter replaced as well..the problem is when I start the car its starts up and run but when I'm driving and come to a stop there a rough idle and it cuts off ..I notice during the winter when I start it up and drive it runs okay til the car warms up..does anyone have a solution???? Someone said it might be the throttle body??? I need help please I really do love my car

Tune up,coils ,air filter. ... Cars & Trucks

Uncommanded acceleration After the Chevrolet Optra Base 1.6 car has run for 30 minutes. Once restart at a signal after cleared to go OR generally stop the engine and restart after more than 30 minutes run, the engine speed zooms up to 3000 rpm without push on the accelerator. The replacement of Inlet air control unit, Air inlet valve Body and Electronic Control Unit did not help. Can anybody help?

... 2007 Chevrolet Optra 1.6

My 2000 chevy silverado 5.3l starts fine, but after it has sat for a little while... i go to take off out of my driveway, and it boggs out bigtime! i have replaced both the fuel pump and fuel injector pressure sensor within the last month and they are both in perfect workin order. ive also replaced the fuel filter. MAF sensor? fuel injectors? please...any ideas would help.

Hi! Before going to the fuel injectors please have the MAF checked. It really has a big contribution on engine performance specially on the idling. The MAF may need replacement for it may have been faulty due to long time use. HOpe this helps and hav ... 2000 Chevrolet Silverado

Car chuggs when in idle mode and stalls at lights and stop signs. Now the whole motor vibrates when excellerating? Took it to a few people, had plugs, wires, coil, 2 o2 sensors, camshaft sensor, and fuel filter replaced. There is probably more I have done but that is all I can think of right now. I have a 2004 Ford Taurus SEL with 109979 miles on it. Can you help me. I just paid it off and trying to decide which would be cheaper, get a new car or get this one fixed. Please Help. Thank

Check for a sticking EGR valve and for intake vacuum leaks. Check for compressed air blowing past an injector--could be a bad o-ring seal. Check for a loose spark plug. If one cylinder is dead (due to low compression), you would be dow ... 2004 Ford Taurus

Vehicle cranks but does not start have replaced crank sensors have replaced cam sensor and PCM only two of my coils fire u can use one of the working coils to check for spark at other coils plugs and there is none...wen starting the vehicle it sounds like its out of time sometimes and others it spens over fine....i am getting fuel to cylinder jus not spark to all cylinders.....at times vehicle will start and run fine for about 1 minute then die after that it wont restart.....can u please help me

Sounds like u need two coils ... 1995 Nissan Maxima

Good afternoon I have a Nissan Caravan 1999 4x4 and it stops as you are driving it, a quick turn of the key restarts the engine. We have power to the fuel solinoid ( I have a test lite set up so I can moniture the power to it) but it goes out when motor stops. It can stop 10 to 20 times on a 20km trip one day and next day may stop a couple of times. We have replaced the ignition switch top wireing loom. no change. could it be a relay and if so were would I find it. Please help. Thanks Stephen

One thing to know is the computer controls the fuel pump when the engine stop running the computer turns the fuel pump off after about a second. One thing you could check is have the computer to scan for trouble codes. Also clean your battery cable ... Nissan Minivan

Was driving on freeway and my 93 jgc motor just died and i rolled to a stop fuel pump is new and working replaced crank sensor, cam sensor, map sensor, tps, coil, plugs, wires, cap, rotar, ign switch, coolant temp sensor and i have 2 pcm's that work and both flash error codes 12 and 14 i am stumped and angry please help me !!!! ps alarm is bypassed it is grounded out inside drivers side door

I found DTC 12 indicates battery input to the Powertrain Control Module (PCM) was disconnected during the last 50 key starts.(you possibly had unhooked the battery at some point?)I found DTC 14 for vehicle OBD1 to be >>1 ... Jeep Grand Cherokee

Just put a computer box in my 1990 Honda accord.Now when I'm almost to a stop it shuts off why please help me ????? they think it's the speed sensor.

Does car have any codes from engine control module-[computer]. is the car being worked on by a repair shop ?.I do not think the speed sensor is at fault. if it has a speed sensor code with other codes it could be a rubbed threw wiring harness under i ... Cars & Trucks

I have a 02 jeep liberty that the speedometer stop work an check engine light came on. Went to Advanced auto they said (speed sensor) So I've checked the wires and replaced the sensor that fixed the check engine light but the odometer still doesn't work could it the front speed sensor too? Please someone help.

... Cars & Trucks


Catalytic converter plugged ?...When was it changed last ? ... 1995 Ford Mustang

1998 Ford Explorer v- 6 OHV Check engine light with code for too lean both banks 02 sensor. Have replced oxygen sensors four times. Have replaced muliple vacum lines including PCV hose. Have cleaned mass air flow sensor. Every time time I clear the code it will be back in approx. 7 to 14 days of every day driving. Any help would be greatly appreciated. I have had this problem for almost 2 years. The vehicle has 165000 miles.

OK. Since you have had so much trouble lets check the dealer for an updated software calibration for the PCM (power train control module). Once we're sure there is no "fix" here lets talk about "lean" engine conditions. Lean means one of two things a ... 1998 Ford Explorer

Hesitation in acceleration, I've taken to dealer 3 times, they said it was mass air flow sensor, replaced it, then throtel possition sensor, replaced it, then fuel pump, replaced it, then fuel pump computer, replaced it, then front o2 sensors, replaced them still no help. DOES ANYONE KNOW WHAT TO DO?? Dealer is stumped, they've checked timing, vacume leaks, ecu and wiring for damage none found, fuel injectors grounds, air flow meter, egr for sticking, ALL NO PROBLEMS,, PLEASE PLEASE HELP!! Thank

... 1995 Lexus Sc 400

I think maybe my TPS is gone in my 1998 venture mini van. My check engine light is on and my van stalls out on acceleration once having already come to a stop and taking off again. I have replaced both crankshaft sensors, the fuel pressure regulator, the Mass airflow sensor. When I first start the van and I rev the van the rpm's never goes past 2. It's like when I try to rev it up it chokes. Please help....

You should really have the van scaned before you put any more parts on it. Autozone will scan it for free. You could spend alot of money just putting parts on it. If you can come up with a code/DTC for your problem then let me know and I will be bett ... 1998 Chevrolet Venture Cargo

HI, my 1998 ford windstar has an abs problem. When stopping the brakes are fine until you're almost stopped, then you hear a noise and the brake peddle vibrates up and down. Disconnect the abs and the brakes are fine. We have replaced all the sensors on each wheel, still the problem exists. Help!

It sounds like the rotors are warped. were the rotors turned down when they replaced the pads?Definitley ABS module or something to do with it. Could it be air in \015\012the line for some reason? Does your master cylinder lid seal good ... 1998 Ford Windstar

Truck will crank and run fine till it warms up...when im on the interstate running a steady speed it acts like its running out of fuel or lossing spark... if i let off the gas it will clear up then start acting up again or i can floor it and it will clear up then it will start acting up again...i have replaced the... ecm, fuel pump, pick up in the dist, coil, plugs, wires, crank sensor....please help my sick truck............. its a 97 ram 1500 club cab 2 wheel drive with a 5.2...

Classic symptoms of mass air flow sensor ... Dodge Ram 1500

Brake problem i have a 2001 gmc yukon xl and my brake pedal is almost down to the floor when i brake to stop. I've bleed the system, replaced brake pads every year, no leaks on the lines or any brake system parts but i've noticed the brake pads hardly wear out every time i replace the pads. what else can i do to fix it? please help

Hi Tora, Go to the back brakes. This is where the prob could be. But with you bleeding the brakes, the peddle has went beyond its normal travel causing the rubbers in the master cylinder to get messed up. Happens too often! Replace the master cylinde ... 2001 GMC Yukon XL
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.1795 seconds