Having problems with your Jeep Cars & Trucks ?

How do i figure out my problen

\015 I have this 1996 5.7 v8 vortec gmc with a check engine light code read p0300 and my catylitic converter was glowing as well as the engine shuttering really bad when i put engine in neutral shaking seems to go away slightly as soon as i put it in gear it wants to die anyone have any ideas of what it could be i have disconnected the muffler and im pretty sure i think that it is the catylitic converter but i could be wrong \012\012\012please help im desperate to fix my vehicle as i cant go to work without it\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Thats what it sounds like but the shaking may be one of your motor mounts check your o2 sensors too
Repair Help & Product Troubleshooting for Jeep Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i figure out my problen


Thats what it sounds like but the shaking may be one of your motor mounts check your o2 sensors too ... Jeep Cars & Trucks

I am installing a performance chip on my 2008 vw beetle. I need help figring out which leads are the IAT leads on the MAF/IAT sensor. It has five leads. Turn engine off, remove key from ignition and remove the negative (black) battery terminal. » Locate the vehicle?s Intake Temperature Sensor (IAT) located on or near the intake tube, in the air box or near the throttle body. Figure 1 shows the typical location for the 2 wire IAT sensor. FIGURE 1. FIGURE 2. FIGURE 3. Visit performance


I have Mitchell and I can't find the wire colors anywhere, My wiring diagrams show the MAF and the IAT but the wires do not indicate who's who. I looked everywhere. We get this alot on the newer models because Mitchell and Alldata update the info ... 2008 Volkswagen Beetle

I am having a power steering issue and can't figure it out. It turns right just fine but coming back left it is very tight. No air in system and I can't figure it out.


Replace gear box the valve stuck in one direction auto parts still carry tho its a reman around 150 ... 1966 Ford Mustang

I can't figure out how to remove the OEM door lock cylinder in my 1994 K1500 Blazer. I can get the handle unfastened, but not removed from the door. Also, can't figure out how to remove the retaining clips on the rods.


In order to remove the cylinder, You'll need to remove screws that are by the door handle,\015\012arm rest, under door and side of door and then gently pull back on the\015\012panel as there will also be retaining clips attached and you don't want\01 ... 1994 Chevrolet S-10 Blazer

I have a wet floorboard on front passenger side to back passenger side. It is only in summer when are is running and seems to be worse when really humid. I am pretty sure it is a condensation drain problem, but can't figure out how to fix it. I have pulled the carpet back, but can't figure out where it is coming from. PLEASE HELP!!!


I believe you face this problem in summer whiles using the AC, the evaporator is fitted under the dash around passenger side, the outlet port for water may have got blocked due to dirt therefore the condensed water has nowhere to go but leak into the ... 2002 Jeep Liberty

Are you the smart one to figure out my automotive problem or are you just talk!!! Guru or no Guru. Her goes. I have 2003 mercury mountaineer has to much fluid in tranny but not enough in torque converter. O.K figure it out.


You have torque converter back flowm seen it a million times...\015\012\015\012A hydraulic retarder and control composed of an accumulator, for rapid filling of the retarder; a pulse valve, for controlling fluid flow to and from the accu ... 2003 Mercury Mountaineer

Trying to figure out how to rewind the cable correctly on the right rear window regulator,I seem to have just one more time around the regulator cable pulley,but i cant figure out how to get it to track right and take out that last little bit of slack so that it fits the pulleys correctly, see, even the problem explaination is tough!


Those regulators are not designed to be repaired -- only replaced. The cable spool, pullys and cable are installed as complete components -- the slack is taken out of the cable during assemby at the manufacturer. ... Hyundai Motor 2004 Accent

Someone help!! we have been trying to figure out what is wrong with my 2002 Chevrolet Tahoe. When I go to start it it will turn over but it will not start until the secong or third time, then when it finally starts it acts like it is going to die, but them it starts to run until I give it some gas and it just does not want to go, my husband has changed the fuel pump 2 times already and we still cannot figure out what is wrong. Any info would be great


ICHANGEMYSPARKPLUGWIRESANDMIXEDTHEWIRESUP,HOWDOIFIGUREOUTWEREEACHWIREGOES? ... Chevrolet Tahoe

How do you remove the fuel filler line from the fuel tank? The line appears to be clogged as no fuel seems to go into the tank? Sometimes it will, but very slowly, others it just fills the filler pipe then puddles. Can not figure out how to disconnect the filler line from the fuel tank. There is a flexible connection at the fuel tank but I can not figure out how to disconnect it from the tank itself..


This means your filler flap is stuck closed or your vent solenoid has failed, most likely the vent solenoid. Thanks ... 1999 Daewoo Leganza

I have a problem with my tranny slipping, and also acting like there is no tranny at all. But, sometimes it works... go figure... Do I have to buy a new tranny? Help the truck was sitting for a year but got engine running smoothly. just cant figure out this transmission prob. Acts like the tranny has totally gone out, but sometimes intermitantly, It works. All fluids are proper. when I drive down the street, and then stop, I step on the gas, and it like its in neutral, BUt if I play with


OK---here is the take---your transmission valve bodies are in need of service. The slippage can also be caused by a faulty torque converter.\015\012\015\012You can replace the torque converter for 150 to 300 dollars with a decent one fro ... 1996 Dodge Dakota

I took the fuel selector of cause i only want to one tank but now my sendind unit isnt working for the main tank .Cant figure out why i just thought they switch tanks and the sending unit for the main tank is right at the harrness . do i cut the switch and complete a circuit or is it a ground cause i never took the main tank out and it worked before i took the selector out . it run fine just cant figure out why i cant tell how much gas is in her


The fuel selector shifts the curcuitry to read the fuel and turn on the pump. if there is a auxullary harnes like a y, you nest jus upplug it and leave the main harness to the main tank,. If you cit wires you wull have problems undoing the changes. ... 1985 Chevrolet Chevy

Wiper problem Hey, I was wondering if you ever figured out what is going on with your miata's wipers. Mine just started doing the same thing. If not, at least get back to me and I will let you know if I figure any thing out. Thanks and good luck!


... 1992 Mazda MX-5

Restoring a 1953 ford truck v8 flathead 239 and cannot get fire to ignition switch, distributor or coil. I have tried everything. All wiring is new. have traced all of the wires. cannot figure it out. i have restored 1965 mustang, 1939 ford 2 door sedan and a 1954 ford crown victoria. I just can't figure this wiring out or whatever is wrong. thanks Frank


You should have battery power going into ign switch. if you do not then your wiring from switch to battery is open somewhere. i cant pull a schematic on this but would assume it is not connecting thru a junction block trace this wire back to its sour ... Ford F-100

Battery replacement Trying to get the battery out of a 2002 pt cruier. Everything is fine until i got to the air filter housing(bottom section) But cannot figure out how it comes out. There seems to be a rod in the back of the housing holding it in, but can't figure out how to get around it


Had the same peoblem,disconect air filter hose ,put hands on sides of air filter box,pull straight up ,held on by three plugs on bottom and flat rod near fuse box.Hope I have solved your problem. ... 2002 Chrysler PT Cruiser

Deck installation i just installed a jvc kd pdr41 car stereo in my car and i can't figure out how to connect my second amp to it. I have the first amp for my subs connected and they work fine but i have no sound inside my car because i can't figure out how to hookup my other amp


Does you sub amp have an RCA out on it? If it does you can use that one, If not go to radio shack and pick up and rca spliter. It has two input holes white and red/ leftor right and turn it in to four outputs or 2 other channels. Good Luck. ... 1998 Chevrolet Malibu

Fuel pump some times i can cut the car off & it wount crank back up until it siets for a few minets once & a wile it will go dead wile runing i figured out the fuelpump wasent runing so i put a new one on it guess what it is doing the same thing i figured the fuelpump is loseing the power to it some how please let me know what the problem is thanks.ps it is a 94 acord


Is the car turning over at all when you try to start it? ... 1994 Honda Accord

I turned the steering wheel when the car was off, and now the steering wheel is stuck in a fixed position. I tried to simply start the car, but the key also won't turn. i figured it's just an anti-theft thing, but i can't figure it out. please help, my mother needs the car back in a week.


Hold steering wheel in direction you turned it, force it same way while turning ignition key to on / start position.Be careful not to break key! ... Isuzu Rodeo

Im trying to figure out how to remove the factory Bose stereo out of a 94 Camaro. The CD player doesn't work and I was going to take it to a local repair shop but I can't figure out how to remove it. Are there some sort of clips to remove the plastic molding?


The radio is in the trunk, not under the dash ... Chevrolet Camaro

Broken Blinkers I have a 94 Ford Taurus GL, and I just bought my car at an auction. The blinkers do not work, but my break lights and emergency flashers do. I pulled out the fuse box and saw that I need a Flasher, so I bought one, but to no avail. I figure it must be a fuse problem, but I just can't figure out which fuse it might be-Can you help! My e-mail is [email protected]


Check the bulbs, also make sure there is power at the flasher relay with the key on, if yes check your combo (turn signal switch) please rate -jeff ... 1994 Ford Taurus

Broken Blinkers I have a 94 Ford Taurus GL, and I just bought my car at an auction. The blinkers do not work, but my break lights and emergency flashers do. I pulled out the fuse box and saw that I need a Flasher, so I bought one, but to no avail. I figure it must be a fuse problem, but I just can't figure out which fuse it might be-Can you help! My e-mail is [email protected] I have the same problem, bought a turn signal flasher but can't find where it goes?


Have u checked the bulbs front and rear on both sides? If one bulb is burned out the signals won't flash. Remove the bulbs and check filament. Sometimes the bulb looks good, but the filament has separated, so u might want to try a new bulb anyway. ... 1994 Ford Taurus

Power steering when i turn the wheel it is hard and soft threw the turns better on some days than others. i replaced the belt and the pump but still nothing so i figured the rack was shot. but i drove threw a big puddle the other night and in the morning the power steering was back. it was fine that day i drove several times because i couldnt figure it out, the next morning it was shot again so i thought maby the vaccume lines to the power steering pump but im not sure any help would be great. t


Have u put the car on the rack yet??? up in the air....then get somebody in the car, start the car, turn the wheel back-fourth...if no rack, just put it on jack stands, and try turning the wheel, but b safe.....and smart...so is the belt tight? is a ... 1992 Toyota Celica

Governor I need to figure out how to erase codes off of my Saturn SL1 1996. Mainly the governor so I can go above 100. Will someone help figure out the best way or product to use to do this?


Unplug the battery for about 20 minutes, but before you do, you might want to write down your favorite radio stations since you will have to reprogram them...and you will have to reset your clock, other than that you should be good to go. ... 1996 Saturn SL

Cam positioning Need to know the position of the cam in accordance with the crankshaft on a 1.5. Head was removed for maching and milling and cam was removed as well so I need to figure out how to set the timing on the camshaft. I allready tried TDC on #1 piston(on compression stroke) camshaft pulley at the "up" position and the rotor on the distributor pointed to number 1 plug wire on cap and motor turns over and has fire but will not start. Please help me figure this out!


Did you adjust the rocker arm on the head\015\012\015\012 yes \015\012\015\012 then you check spark and fuel \015\012\015\012 check ur cel for codes \015\012 ... 1989 Honda CRX

Battery dying I have a 2000 toyota, camry, solara, 4 cylinder and last week my battery died. I actually replaced this about 2 years ago as well and figured it was a cheaper one so no big deal. When we went to remove the battery we noticed one of the caps had come off and maybe that was why the battery died so we purchased a new battery last week and everything appeared to be ok. Over the weekend my battery died again causing me to have to jump my vehicle to get it home. At this time we figured o


No the alternator won't keep it running on a Toyota, the system is wired much different than most cars, found this out the hard way on same type of car. Test the alternator, raise the idle up to 1500 RPM turn on everything i ... 2000 Toyota Camry Solara

Front side marker light bulb burned out. Can't figure out how to get to the bulb to replace it. I also have the ''top right'' brakelight bulb burned out & can't figure how to get to that bulb either. It's NOT the one in the trunklid.


You actually have to remove the light from the vehicle to change the bulb. if its the one in the bumper you will have to loosen that side of the bumper to get to the bulb. ... 1998 Lexus LS 400
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0825 seconds