Having problems with your Hyundai XG350 ?

I have a 2002 hyundia xg350 i recently had to change my rear braeks do to waer. replace then with auto parts brraks pads, now the right rear calerper get stuck and my breaks pad get real hot. i can take a c-clanp and puht in the caleper goes all the way in.

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Replace the the brake hose on that caliper. The brake hose has a very small diameter passage running inside and when a brake hose wears out over time, they will internally collapse,and when you apply pressure to the brake pedal, you are able to force the fluid thru, but when the brake pedal is released, the fluid is not able to pass thru the hose on its own and allow the caliper to move away from the disk. If you are able to push the caliper in without using excessive force, then the caliper is ok .At this point, you can just replace the hose or replace the caliper and hose together.
\015\012If your rear brakes have other linkages for the parking brake assembly, be sure it is not adjusted too tight, as this will also cause this issue. Let me know what you find.
Repair Help & Product Troubleshooting for Hyundai XG350

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 2002 hyundia xg350 i recently had to change my rear braeks do to waer. replace then with auto parts brraks pads, now the right rear calerper get stuck and my breaks pad get real hot. i can take a c-clanp and puht in the caleper goes all the way in.

Replace the the brake hose on that caliper. The brake hose has a very small diameter passage running inside and when a brake hose wears out over time, they will internally collapse,and when you apply pressure to the brake pedal, you are ... Hyundai XG350

My 2004 honda cr-v has a burning smell coming from my right rear tire and the rim gets real hot. my calipers and brake pads were replaced but the burning smell is still present and the rims gets hot

The wheel bearings are going out. Most of the time you can replace them easily but some newer vehicles like yours might have a sealed hub in which you must replace the entire assembly ... 2004 Honda CR-V

I have problems with my isuzu trooper 2001 rear left brakes, it seems like the pads get stuck and wear super fast and the rotor gets very hot and smells like something's burning, but the right and front wheels work just fine, what can I do to fix this?

Before you fix anything we diagnose and inspect it first.the caliper is seized (piston inside)or the slider pin seizedor the rotor is cracked or warped.ABS modulator , on this line seized at that end.Any brake feed line to this ca ... 2001 Isuzu Trooper

Once you take the rear caliper loose, how do you get the pads off? There is a clip, but it looked like a special tool is needed, or I wub break the clip. Also, I noticed the pads have little rods run through the top of them, or closest tto the caliper.

Pull the rods out and there should be no worries ... 1999 Cadillac Catera

Rear brakes seemm to be sticking on rear of my 2004 murano, 74K highway miles pads changed by dealer at 55k on rear. afterdirving just 5 to 10 miles rearfotors are HOT like calipers stuck or ebrake stuck. Suspect vdc control problem started after a very fast stop with a swerve couple months back. brakes dradding so bad the mpg has went down to 16 :0 mpg rear rotors are becoming warped. Can brake bias be off perportining valve stuck?? VDC freaking out ?? HELP!!!

Take your rear calipers off and lubricate the pistons with bearing grease,move them up and down with your fingers till they move more freely,then remove the dirt from the a.b.s sensor if any with w.d 40. Then check to see if your emergency brake is ... Nissan Murano

We're changing the break pads and break drum on a 1995 chevy corsica, we're also replacing the break fluid valve and we have to take the wheel cylinder off and we can't manage to get it off to take the break fluid valve off and replace it. Where do we go from here?

Is the wheel cylinder held on by 2 bolts or sometimes a clip, ... 1995 Chevrolet Corsica

Steering wheel vibrates when i apply brakes. I have replaced rotors, calipers and breaks 3 times and the problem comes back after about 6 months or so. Any Ideas? Is this a flaw in design? are the breaks getting so hot that they are warping the rotors? I was told that when i come to a stop light i should not hold break on same spot ,That i should rolll a little bit so the break pad does not stay on same spot of rotor. that it can create a hot spot. Anyone ever heard of this ?

Had the same problem, took the roters in to get grinded and the problem went away. ... 2002 Dodge Intrepid

Trying to remove rear wheel cylinder from buick skylark 1997 do i need to remove axel to get the cylinder to come out ,removed it to the point where it is stuck between tire mount spindle and top bracket that keeps drum pads straight up and down ,there is a spacer like thing that holds the top springs secure that is where it is getting stuck, not enough room to get it out.

You shouldn't have to pull the axle.Do one side at a time so you always have a reference to go back to, even if it is a mirror of it.Always do both cylinders though, or the other one will leak in a couple of weeks or so. They both do the ... 1997 Buick Skylark

Rear brake pad dragging. I recently replaced the front and rear brake pads on my 2000 chevy silverado 1500 truck. The driver side rear brake seems to be dragging and getting hot. I removed the tire and caliper again but did not find anything wrong. Any suggestions?


Brake dragging After i changed the rear shoe and calibrated, after a while, the breakes self adjust so it gets too tight and start dragging and getting hot. I have to be loosing them with frecuency.It looks that the hand breake adjusting level dos not has a limit. Avery time i pull the hand breake, the level turns the adjusting star and does not have limit but the drum. Do you have any recomendation?

Had this before no end of times,their is a sprung piece of steel on the opposite side to the adjusting lever and you have left it off.drill a hole through backplate in line with adjuster and remove the auto adjuster,then when you service vehicle adju ... 2006 Toyota Land Cruiser

Question 1: How do i remove the rear rotor on my 1990 chevy Lumina Euro 3.1? I can't just pull it off. Is it just stuck or do i need to remove some kind of nut keeping it on? If so, where is it located? Question 2: On the front brakes, the brake pad that's controlled by the piston hits the rotor causing the rotor to move and make contact with the outter non piston controled brake pad...Does the rear break pads work the same? If not, how do they work?

Disc brakes work on a clamping principle as you said, on the rear of the lumina the caliper sliders tend to seize causing only the piston side to actuate, you will have to replace these pins and bushings as well, have fun ... Chevrolet Lumina

I changed out the rotor on the drivers side rear and breake pads on all tires 2001 chevy 1500,when i tried to set the breaks the rotors got hot quickly the rear caliers on both locked up and wont release

Check the emergency brake cable ... 2001 Chevrolet Silverado 1500

On the rear caliper brakes I am installing new pads. I cant get the caliper to retract. Do I have to adjust the parking break 1st. and how do I get access to the parking break adjusters.? Do I have to remove the console? I have an A4 manual and it is not the same for the the A6.

... Audi A6

I have a 1999 Jimmy that I bought used in the middle of winter and never noticed any issue with the heat. Now that it is getting warmer I am roasting all the time! I have the fan off and even when I put the temp on 62 or whatever the lowest setting is there is always HOT air blowing in. The faster I go the hotter it gets in there! It seems that the heat is stuck on and the vents are stuck open. I don't have a lot of money to spend taking it to a mechanic to put it on a machine to diagnose a

You could try and pull out the heater controle panel from the dash if it is cable opperated check to make sure the cable is attatched an not broken, if it's vaccum operated you may need to replace the vaccum lines. ... 1995 GMC Jimmy

Can't get into the rear drum to replace break pads.

STOP, STOP!! Don't hit the drum with anything other than a copper mallet not weighing more than a couple of pounds. You will wreck the drum.Get a Haynes manual or knowledgeable friend because drums with high wear have a fair lip on the inner edg ... 2000 Ford Focus

2006 Honda Accord. Rear pad replacemnet. I couldn't push in the piston with my C clamp, Is there something that holds it from going back in, have replaced many pads. This didn't want to move, and I didn't want to break it. Put the old pads back til I get answer. Thanks Dan Spencer

Rear pistons generally need to be turned as they are retracted. Most parts houses sell an inexpensive "universal" tool for this It is a 1" cube with different "bumps" that fit a number of pistons. ... 2006 Honda Accord

I have a 2006 Ford F-250 powerstroke and what my problem is the driverside rear brake seem's to be sticking the whell would get so hot you couldn't touch it took it to the ford garage and they said the brake pads were rusty so they installed new pads on both sides and turned the rotors $164.00 out of pocket and I have extended warranty. The old pads were still like new. This truck has 32,000 miles on it. and the service guy garanteed me that would fix the problem well it didn't and know its star

Yes very common issue for caliper slides on the bracket to freeze up with rust and cause dragging calipers. ... 2006 Ford F-250 Super Duty

Rear heater blows only cold air no matter what the settings are at. Front heat works well. I have tried using both the front and rear controls to set the temperature, but the rear vents will only blow warm air at best. The air starts out as cold as the outside air even when the engine is warm and the front is blowing hot air. It takes several minutes for the air to get slightly warm.

If this is equipped with a rear heater core it is probably plugged up and needs to be disassembled and cleaned out ... Chevrolet TrailBlazer EXT

Front AC works for about an hour the fades away. Rear AC does not blow cold. Previously, rear AC worked and fine front wasn't blowing cold, then neither worked, now only front for about an hour before air sloly starts to get warm. Hotter it is outside the colder the system seems to tink it is inside. burst of cold every once in a while once air is hot. 1 mechanic said everything fine but sensors need recalibration and likely sticking valve why no rear AC - and to take to dealer. dealer sai

There is a electric motor on top of the a/c plenum case that moves a door that is control of the air temperature---these motors are known to go bad ---A test you can do is to move the temperature knob all the way to cold and then all the way to hot a ... 2003 Chrysler Town & Country

After changing rear brake pads and rotors on both sides, when brakes are applied they squeak? and when i accelerate it sounds like the caliper gets stuck?

... 2008 Dodge Ram Pickup 1500

I understand that I will need a special tool to screw in the piston when I change the rear brake pads on my 2003 tiburon GTS. Where can I get this tool and where can I find the instructions for replacing the real pads?

It's fairly easy and the tool cost less than $10 at most auto parts stores, so why rent it? As for instructions...here you go:- "Loosen" lug nuts. - Jack the car up. Support with jack stand(s).- Remove previously loosened lugs ... 2003 Hyundai Tiburon

Rear brakes way too hot. replaced the pads and very difficult to turn in, in fact had to releive pressure at the hose to get it to go in at all. Is it possible that the master is at fault? I don't want to waist more time and money rebuilding or replacing the calapers if they are not the problem... i did find the parking brake cables were shot so replaced them.. better but still way too hot...any info??

This seems to be a common problem with the trooper.\015\012I replaced both calipers on the rear as they had the same problem. ... 1991 Isuzu Trooper

I have a ford fiarmont eb 1992 and i have removed the rear break pads and now i need to put the new 1s on but to do so i need to wind the the piston in how can i do this with out buying a rear piston resseting tool and if i can should it wind in easy cause i tryes to wind it and its real tight thanks

4 wheel disk? i use a large C clamp and a pair of channel locks slight pressure and twist ... Ford Fairmont

Engine cuts out when driving electrics still ok only engine,cuts out then have to wait few moments or some times mins before will start again...then might go days or weeks untill it does it again, then some times could happen 2/3 times in space of a mile or so help please,,,got to get rear brake and discks for car was going to take to dealer vw may be ask them to take a look any idea on price of diog test been quoted 161,for disk and pads fitted car spec 1997 golf gti p reg

Check sensors for cam and crankshaft ... 1997 Volkswagen GTI

I get sufficient heat in my 1998 Olds Silhouette on the upper, lower, and bi-level settings. However when I switch to one of the two settings that use the defroster the temperature of the air coming out goes down. Instead of being hot air it becomes a cool/lukewarm temperature. The temperature of the air in the rear of the van seems to remain hot. We thought this might be a thermostat problem (since the van took and still takes a long time to warm up and in my opinion never reaches maximum opera

Change your heater core ....will solve problem ...big job ..if your not sure how ..have it done professionally ... 1998 Oldsmobile Silhouette
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.5652 seconds