Having problems with your Hyundai Elantra ?

2001 elantra how do i replace the turn indicator switch?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Hyundai Elantra

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

92 nissan pathfinder turn indicator switch doesnt work; replaced flasher still doesnt work also have broken emergency flasher switch which iam replacing. is hazard switch and turn indicators connected?


... 2002 Nissan Frontier Crew Cab

2001 elantra how do i replace the turn indicator switch?


... Hyundai Elantra

Key wont turn on 2004 Alero. If key is inserted and door is opened the alert bell sounds off indicating keys have been left in ignition,but that is all that is functioning. Have tried 2 different keys and ignition will not turn. Need i replace the entire ignition switch or is there a way to determine which part of the switch to replace?


Ignition lock cylinders are pretty notorious for this. You may get the thing to turn by wiggling the key up and down while turning at the same time. I have also had luck in tapping on the cylinder with a screwdriver handle while turning the key. T ... 2004 Oldsmobile Alero

How do I replace the ignition switch on a 1999 chevrolet suburban? After the key is placed in the ignition switch, the key becomes very hard to turn and activiate the starter. I ''jiggle'' the key, turn the steering wheel, place my foot on the brakes...no help. Ignition is probably worn out and needs to be replaced. How do I do it, please. Also, how do I identify the low pressure nozzle for the air conditioner? The two outlets are virtually identical and there is no indication on either nozzle/h


For the a/c, if caps are still on valves, blue side is low and red is high. Also, looking at the the valves one is slightly smaller. The smaller one is the low side.\015\012\015\012As far as the key cylinder, you must remove steering wheel, lock pl ... 1999 Chevrolet K1500

How do I replace the ignition switch on a 1999 chevrolet suburban? After the key is placed in the ignition switch, the key becomes very hard to turn and activiate the starter. I ''jiggle'' the key, turn the steering wheel, place my foot on the brakes...no help. Ignition is probably worn out and needs to be replaced. How do I do it, please. Also, how do I identify the low pressure nozzle for the air conditioner? The two outlets are virtually identical and there is no indication on either nozzle/h


You have to take the steering column cover off and then find the little hole near the ignition tumblers. you put the key in and turn it forward one or two clicks, find a small screw driver and push the little pin in the hole. that is what holds the ... Chevrolet 1500

I am working on a 1991 Audi 100. The turn signal lights stay on steady and not flashing when the signal switch is turned on after I replaced the wiper switch. Also the emergency lights only work when the ignition key is off. I installed a new flasher relay and checked all the light bulbs but it makes no difference. In addition, when the dash lights are turned on, the signal indicator lights come on dim. I know there could be some current feedback in the system but do not know how to trace it. An


If you replaced the wiper switch and this problem occured, you have a bum switch or the wrong one. ... 1990 Audi 100

My dash lights wont come on. when you try to turn on dome switch, the four ways and hight beam indicator lights come on and the seat belt light. I tried replaceing the dome and head light switch, but every time I plug in the new one or old one I get different light problems and still no dash lights. All external lights work fine. also when lights are on and I turn on turn singal my fuel gage goes up and down. all fuse are fine. can any one help? 1988 chevy s-10 pickup


Bad ground , check ground at headlight switch, or behind dash ... Chevrolet S 10

CHECK ENGINE LIGHT WONT LIGHT.MUST LIGHT WITH KEY ON TO PASS EMISSIONS .I ALREADY REPLACED THE BULB WHICH WAS BAD'CHECKED CIRCUIT BOARD OK. ALSO TURN SIGNALS WORK NORMAL BUT WHEN YOU PUT THE 4WAY FLASHERS ON THE LIGHTS ALL FLASH NORMALY EXCEPT THE INSIDE INDICATORS IT FLASHES THE HIGH BEAM IND. INSTEAD I REPLACED THE FLASHER UNIT AND THE TURN SIGNAL MULTIFUNCTION SWITCH.


Sounds like a crossed wiring connection somewhere, if the four-way flashers are turning on the high-beam indicator.\015\012Check all the connectors in the associated wiring harnesses for the instrument panel.\015\012Good luck! ... 1996 Ford Explorer

The right head lamp in my 2004 Dodge Ram 2500 does not come on. The " Lamp Out" indicator on the instrument cluster is on. I replaced the right head lamp but is still does not come on. When the head light switch is on and I turn on the right blinker the right blinker blinks fast. The left works normal. When the head light switch is off the right turn signal works normal.


You have a crossed wire or a wire is shorted in the headlight and the blinker circuit. The reason I say so is because you said the blinker goes fast when headlight is on. That is the flasher doing that. That is because of the 'load' is different whe ... 2004 Dodge Ram 2500

Turn signal periodically the turn signal will stop working. When the truck is first started the turn signals will work fine. After 5 or 10 minutes of driving the turn signal will stop working. The interior indicator will stay solid as will the exterior turn signal lights ( all lights work). We have replaced the fuse and the turn signal switch.


Now replace the flasher unit! Frankster016 ... 2002 Nissan Xterra

Key Stuck I turned off my 1997 Jimmy and the ignition would not turn to the position that allows you to remove the key. It turned off the motor but wouldn't turn far enough to release the key. I turned the car back on and off and then it worked OK. What is this? A one time thing or indicator there is a problem? I've also been having a problem with the headlights flicking off for no apparent reason. I'm getting the light switch replaced tomorrow. Are these two things related?


Lubricants will help this problem short term, but the only way to fix this is to replace the cylinder lock.\015\012the tumblers inside are getting loose and not falling into place every time the key is in the off position.\015\012If it is ... 1997 GMC Jimmy

Front driver side turn signal light doesn't flash.replaced bulb,replaced socket,all other lights work on emergency flasher,except front driver side.rear driver side turn signal light works,but flashes fast,also when turn signal switch is on for driver side turn signal,no indicator light on instrument panel.running light driver side front has power,just no flash.


Replace flasher......usually located in fuse block area...listen in this area....select passenger side ...then select driver side...you can hear flasher clicking...you have seperate flashers for each...FLASHERS are small cubes plugged into fuse block ... 1998 Buick Century

My high beams won't work and the high beam indicator in the dash won't come on when the switch is activated either. I've checked the fuses and replaced the turn signal/dimmer switch and they still don't work. Is the problem in the headlight switch? This is on a 2001 Mercury Cougar.


Replace the HI/LO Beam Relay.Regards.DT ... Mercury Cougar

S10 1999 bearings bad 0 oil pressure,removed and rebuilt engine, replaced most all. back in and...Won't start, not a crank or a ticking from the starter. Starter and starter selanoid, battery all tested OK.conecting to starter and starter getting power. Replaced neutral safety switch twice , check all 3 relays all OK. Still no response. Lights and accessory lights all go on when ignition turned. Have tried all gears but still nothing. Could I have forgotten to replace something. Is there a way t


Yes, you can hotwire the starter, use a button starter to energize the solenoid. there is a chance thet the new or rebuilt starter isn't working. it has happened to me I went an bought a newly rebuilt starter but it was no good, it happens sometimes. ... 1999 Chevrolet S-10 Pickup

When applying the brake the left turn signal indicator and left turn signals come on I've already replaced the turn signal switch and checked what wiring I could all looked well


Definately a short to the indicator. there has got to be a wire grounding. electrical expertise required ... 2005 Jeep Liberty

I have a 1991 Toyota camry and the a/c switch doesn't turn on. I replaced the switch tha fans work and the freon has been charged. I am wondering if a fuse may be causing the malfunction. Oh the switch has an indicator light and doesn't come on therefore no cold air is being dispersed in the car.


I replaced a/c compressor on 1991 toyota camry.I cross wires and compressor came on but would not stay running.Is there any fuses or relays that could keep compressor from coming on. ... 1991 Toyota Camry

How do i replace the turn signal switch? I have checked the fuses and they are fine. I have no hazards and no indicator lamps. I've been told by a few people that it has to be the switch. Please help !


Do you have brake lights? If so, change the 4way flasher unit. It's on the fuse block ... 1994 Pontiac Grand Prix

Hi,I have a 1997 VT commodore. Every time I turned the indicators on, the high beams came on. Was told it was a faulty switch. Over the weekend my Uncle (who is a mechanic not an auto sparky), changed the indicator stalk and now my car won't start! We left it with him and yesterday morning he went out and rolled the car into his garage and then it started. He realised the ignition barrel was sticky so he replaced the ignition barrel. The car started fine. I went and picked it up last night a


... Cars & Trucks

I have a 72 F250. I had to replace it with another column from an earlier model F250 67-68. The neutral safety plugs in and works fine, but the other harness was loose wires. How do I get everything working again ? I matched up the wires that were of similar colors, but I get turn signal indicators on when I press the brake. 4 way works with headlights off, but not on. I can get the left side to work correctly, but only the front right works on turn signal switch, but the bulb is good. I am lost


Use your old wire harness ... Ford F-250

I have a Grand Cherokee 2001 4.0 6cyl. Thermostat replaced, oil sending switch replaced but still losing coolant fluid. About from full to indicator light in six weeks. My oil pressure gauge went to almost 0. I had it checked out and the mechanic said the oil was very thin. Changed oil and filter and oil pressure resumed main seal products to correct this to 40psi at 1600 and 20psi at idle (pressure in the oil pan). For the next 1000 miles it was good, and then the oil gauge was showing a dip a


Hate to say it, but sounds like a blown gasket or cracked head - the mere indication of the white mily substance.If you haven't done so, it is time to do a compression test. Alternatively have you checked your oil pump itself?Best r ... 2001 Jeep Grand Cherokee

My 96 grand prix's air conditioner compressor will not turn on when the switch is activated. I have replaced the large fuse under the hood but that still hasn't solved the problem. The indicator light on the ac button is lit but the air conditioner will not turn on.


System is low or empty. you need a high and low gauge to properly check it out or just add a can or two. ... 1996 Pontiac Grand Prix

When the headlights are turned on,the backlit light for the driver side heated seat switch doesn't come on- the indicator for heat level DOES come on when the button is pushed- can I replace the bulb responsible? The backlit light for the climate "mode" turndial is very faint- can I replace the bulb? 2006 Jeep Overland thank you Norm @ [email protected]


The heated seat switches are both mounted in the instrument panel. The two switches are part of the lower instrument panel switch pod assembly. If either of the switches is damaged or inoperative the complete switch pod assembly must be replaced. ... Jeep Grand Cherokee

I have a 2001 Mazda MPV and my left turn signal stays on. Both the front and rear and the blinker indicator light also. It does not flash the light stays on. I replaced the the turn signal switch but that did not help.


... Mazda MPV

1998 GMC Sierra. Blower motor works sometimes. No particular circumstances, just when it wants to. Checked all fuses, relays, even replaced the resistor, nothing. Followed the wire harness and found the two pigtails that others have mentioned. Took the wires off, black and purple, and turned ignition on. Getting around 11 volts on all sittings except for the highest setting, it reads 0 volts. The compressor turns on at the console, all the switches on the console work, just not the fan.


Could it be the blower motor it self? sometimes they have a "bad spot" when it is not working, can you hit it and make it run? pretty common on these trucks. the switch is also common. they often melt at the connector on the back making a bad connect ... 1998 GMC Sierra

I used my emergency brake for the first time since i bought it one year ago. Noe the indicator light on the dash won't turn off. I replaced the switch behind the pedal, disconnected the battery. It just keeps turning on.


Check your brake fluid level. ... 1990 Chevrolet C1500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.4625 seconds