Having problems with your GMC Denali ?

Is changing a transfer case output bearing on a 1999 yukon denali a job that a semi experienced person can do, or is it a dealership job because the seals need pressed in or something. Can the front shaft be taen off and the truck driven without harming it?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for GMC Denali

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Is changing a transfer case output bearing on a 1999 yukon denali a job that a semi experienced person can do, or is it a dealership job because the seals need pressed in or something. Can the front shaft be taen off and the truck driven without harming it?


... GMC Denali

I need to replace an output shaft seal on the passenger side of my hyundai santa fe. What needs to come off? Its a 2004 v6 2.7 liter its the front seal where the axle goes into the transmission. I have taken off the bracket holding the inner and outer shafts loose but still don't have enough room to pull the shaft out of the transmission. Do i need to remove the alternator too?


1. remove the aluminum wheel cover using a flat blade screwdriver.\015\012\015\0122. raise the vehicle and remove the wheel.\015\012\015\0123. remove the cotter key, and remove the axle shaft nut.\015\012 ... 2004 Hyundai Santa Fe

Front seal the front seal on my 94 Taurus SHO is leaking ! Is this something I can fix ? and how hard is it to do and what tools would I need to do the job ?? If I cannot fix it my self is it a costly job ?


You can do it and it will be messy, but much cheaper than $80/hr at a shop, provided you have the time. Best thing is to get a repair guide at an auto parts store (Chilton or Haynes) and with the text and pictures, you will know what to do, how to d ... 1994 Ford Taurus

I need to replace the front crank seal on my 98 audi a4 and also the passenger side cam shaft seal i have access to both i can not get the cam seal out any ideas on to get it out ? and also i can not remove sprocket on the crank shaft to get to the seal any ideas on how to get that out ?


... 1998 Audi A4

I think the front axle seals on my 1999 dodge 3500 4x4 need to be replaced. I am replacing the sealed bearing hubs and I wonder how big of a job it would be to switch out the axle seals inside the differential housing. I already drained the oil and removed the cover, but I am reluctant to unbolt the ring gear assembly. Would it be safe to leave the seals and hope that they don't leak? The truck has 200,000 miles on it and up to now has been a great truck. Thank you in advance for any help t


If you have the hubs of than you dont have much futher to go to replace the axl seals. just slide out the axls the passenger side is two pice then take out the four bolts that hold in the carrier gear then pull out the hole gear asemblie the driver s ... 1999 Dodge Ram 2500 4WD

How do I disconnect the rear drive shaft of my 2000 Dodge Dakota (quad cab) 4x4 V8 5.9? I took the 4 bolts off, but everything remains solid. The front half looks like it should slide out, so do I need to pop the cross & bearings apart in the back in order to remove the shaft? Will it ruin something if I drive it without the rear drive shaft connected? Thanks! Linford W.


You have to take cap scews off the rear of driveshaft the drop the rear and pull out towards the rear ... 2000 Dodge Dakota Quad Cab

O4 envoy need to replace axel shaft seal front drivers side how does the axel shaft come out is it holding on by c clip around the end of the shaft how does that come out w a block o wood and hammer?


Yes it just pops in and out a block and hammer should do it\015\012its a tight fit!!! ... 2004 GMC Envoy

How do I replace a front wheel bearing hub assembl in a 2007 toyota tacoma 4 wheel drive?Does the bearing need pressed onto hub and what size socket needed to remove hub?any thing else I might need to know to do this job myself


... 2007 Toyota Tacoma

I pulled my cv axles (front) and in doing so ruined the seals where the inboard shaft passes through the seal out to the hub, I need to know what part the seal number is and what it may be called, please help me if you can. Thanks: Dave


Wheel bearing dust seal, ... 1997 Honda Passport

I need to know if front seal on a 2.4 liter chrysler can be replace without pulling the front cover


... 2006 Chrysler PT Cruiser

Leaky Transmission My 1997 Ford Taurus is leaking transmission fluid from the right front axle seal, and transmission pan gasket. I'm going to do a transmission service while I'm replacing the pan gasket, but i would like to tackle the axle seal as well while it is drained. what tools am i going to need to do that job?


You would need a toolbox full of tools-wrenches, 1/2 inch drive ratchet wrench and several size sockets, one large socket for the big axle nut at the center of the wheel-possibly 30 mm, not sure. Yes, quite a number of common hand tools required for ... 1997 Ford Taurus

1993 GMC Rally/Vandura G2500 Style--IC 4.3 liter,6 cyl,automatic. Tranny slips in 3 rd gear and above.Replaced front and rear seal,still leaks.Will only move 25-30 miles ahour. Can"t find any identification name plate attached to the case exterior on passenger side ,just in front of where the tail shaft housing bolts to the main case.Everybody i talk or contact gives a differant tranny # which we need to get another one.I HOPE YOU CAN HELP and will be waiting to hear from you


... GMC Vandura

I'm changing a front whell bearing/hub assembly on 2003 yukon xl 1500 4wd and need to know if the brake caliber is pressed on and off or if I can remove it without a press?


I agree w/ Dieselpro, once you take off the wheel the only thing you need to do is by using a breaker bar, unloosing the 2 nuts that is holding the calibor bracket and then you can remove the calibor, brakes and calibor all as one unit. The rotor wil ... 2003 GMC Yukon XL

How do you replace Disc Brake Pads in a Lexus LS 400? I've done many front Break jobs, but not sure exactly how to replace pads in this car. It seems that there is a way to just slide them in without removing the whole Caliper Assy. It seems like there is a way to slide them in just like bread into a toaster. Of course I 1st need to remove the warn pads somehow. Please clarify how to do this, and if I need to remove the caliper Assy and if so, How exactly? Thank you! Much Appreciated. J


Hi, jack up the car, remove the wheels.\015\012\015\012\015\012If you are using a hydraulic jack, this is the jack point I used.\015\012\015\012\015\012(Unlike many other models, the caliper does not have to be removed to chan ... 1998 Lexus LS 400

Front drive shaft has a bad grinding noise and the rear seal has cracked and the bearings are exposed and all the grease has leaked out. do i need to replace the entire shaft and what is the diffuculty and cost of doing so.


Found a website that builds brand new drive shafts with spicer u-joints for a reasonable price\015\012\015\012http://www.alldrivelines.com/Jeep.html ... 2002 Jeep Liberty

I have a 1989 jeep cherokee that has a roaring noise in the right front. it sounds like a wheel bearron and or u joint going bad. is it very difficult to change and do I need specal tools to replace the wheel baerron and u joints. I have replaced the rear main oil seal without pulling the trans or droping the front end, which all the information said I whould have to do one or the other. Can you help?


Sounds like a wheel bearing,to check jack it up on that wheel then from top to bottom grab the tire and then try to move it up and down like your trying to pull it off if it moves alot its bad.no it doesnt take any special tools but it is difficult t ... 1989 Jeep Cherokee

Hey fellas, i have an 02 liberty with automatic trans, the front drive shaft went out last year when the differential seal went. when i had the seal repaired i didn't have the money to replace the driveshaft, so i had the dealer just remove it. now i want to put it on and cannot afford to pay the dealer.. is there any thing i need to align when i replace it? pllease help.. thanks robb.


No there is nothing that needs to be aligned, you can simply put the new one in, just make sure you tighten the shaft bolt down as tight as it will go. ... Jeep Liberty

How do i repair the gasket behind the crank shaft seal?I have a major oil leak and i was told my gasket behind the crank shaft in the front needs to be changed. I have nearly no experience on vehicles so if anyone knows how to do this please tell me in detail. thanks sooo much.


Front crank seal. First you have to have room to work, so this may require you remove the radiator and some plastics. Remove the serpentine belt,remove the bolt in the center of the crank pully. The pully should slide off with some resistance but ... 1994 Dodge Caravan

I have a 2001 chevy silverado 4 wheel drive truck. I need to change the front hubs and half shafts. Can the half shafts be removed and replaced without removing ball joints? I appreciate any advice you can give. Thanks.


... Chevrolet C1500

2001 Dodge Dakota Sport 4x4. The Front seal of the rear axle appears to be leaking as the case is covered with oil. Can the Drive shaft be dropped and pull the shaft out of the axle to replace the bearing/ and or gasket without opening up the axle cover?


... 2001 Dodge Dakota

I need to change a water pump on a 1996 Hyundai Lantra and I was wondering if I can do it without taking the engine out. While I'm doing the water pump I might as well replace the timing belt as well but would need to know how to align the timing and if there are any other replacement recommendations (seals etc) while I'm doing the job.


Hi Steve-e-t-t,The water pump is located directly behind the pulleys near the center\015\012of the timing covers. You'll need to remove the timing belt to get the\015\012water pump out. Once you've got the timing belt and pulleys ... Hyundai Elantra

Is it bad to replace the cam and crank seals, while doing the timing belt, without removing the shafts i.e. cutting and prying them out)?


Haynes manuals get their information from factory service manuals, so I believe you could do as described in the Haynes book. Just be careful not to scratch up the seal surface on the shafts. ... 1995 Toyota Tacoma

Are the front axle shaft seals on a 2500 Ram 4wd unit owner replaceable or do you need specialized dealer equipment. If owner replaceable what is procedure.


... 1999 Dodge Ram 2500 4WD

I need a parts discription with an exploded view of the front differential ,for a 4x4 2003 , 1500 series z-71 extended cab. I replaced the passanger side axle output shaft roller bearing and seal. Im not sure if i have the engaging gear flipped correctly when I slid the shift fork around it. I don't want go any farther until i am confident it is assembled correctly thank you sooo much .Note I do have a Hayes paper back but only the procedure is covered there are no illisration shown. Thanks Rich


... 2003 Chevrolet Silverado 1500

THE TOYOTA GARAGE SAY THAT I NEED TWO OIL SEALS IN THE FRONT OF MY CRANK FOR A TOYOTA LAND CRUISER 2001 4.2 D. I HAVE GOT A OIL LEAK ON THE BACK OF THE CRANK PULLEY. 2 . WHAT CAN HAPPEN IF YOU DRIVE THE CRUISER WITHOUT A DAMPERPULLEY


The damper pulley, on the end of the crank is what drives the belts for pretty much everything else. the engine will overheat, the alternator wont charge, the power steering wont work, the air con wont work, \015\012the back of the pulley has a ... 2001 Toyota Land Cruiser
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.7886 seconds