Having problems with your GMC Cars & Trucks ?

I have two codes on my 2008 gmc sierra sle 5.3 liter

\015 The codes are p0036 and p0054\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Both codes are for the O2 sensor bank 1 sensor 2 which is after the cat converter. Code 54 is for the heater in the sensor which could cause code 36 if the heater is not working.
There may be a problem with the sensor or the power source for the heater. The sensor is heated at start-up to quickly read the exhaust gases.
Repair Help & Product Troubleshooting for GMC Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have two codes on my 2008 gmc sierra sle 5.3 liter


Both codes are for the O2 sensor bank 1 sensor 2 which is after the cat converter. Code 54 is for the heater in the sensor which could cause code 36 if the heater is not working.There may be a problem with the sensor or the power source for th ... GMC Cars & Trucks

I have 2006 GMC Sierra SLE 4WD 5.3 liter and my engine light comes on giving me the code PO449 Evaporative Emission Control System Vent Valve/ Solenoid Circuit Malfuction. What could cause this code to come on?


There is a solenoid that open and closes with 12 volts, usually located close to the fuel filler tube area. This open to allow you to fill your tank, then closes after some inputs for the computer are satisfied, and then a pressure sensor verifies th ... 2006 GMC Sierra 1500 2WD

I have a 2002 GMC Sierra 1500. 4.3 liter engine. I brought it to autozone and they put the gauge on it and got two codes P0140 and P0300. I had my distributor cap replaced, ignition rotor, plugs ,wires, and fuel filter. What now?


Clean mass air flow sensor with a nonchlronated brake cleaner,install new air filter and check all vacuum lines for leaks then check for vacuum leak around or at intake manifold.Code P0140 is for mass air flow sensor code P0300 is a multiple misfire ... 2002 GMC Sierra 1500

Have a 2001 GMC sierra 1500 SLE PO449 code


... Cars & Trucks

I have a 2006 GMC Sierra 5.3liter/automatic that is giving the p306 code. I have replace the ignition coil on the passenger side that is third from the front of the truck (#6), and the problem persist. The code is not persistent and will cut off on its on. It mainly occurs when the outside temperature is very hot and the truck becomes sluggish and the motor begins to miss severely. On two occasions the engine light has flashed. I have not noticed and rotten egg smell, but I have heard that ther


Pull # 5 plug and have a look at it .. because they fire so close to each other it can confuse the pcm about wich cylinder in having a problem. I have seen this between #7 and #8 on a few occasions. As you see the firing order has those two close tog ... 2006 GMC Sierra 1500 2WD

P0300 code on scanner showing random misfires on my 1996 GMC sierra, 5.7 liter motor, gas line pressure at 55 psi at idle. Replaced fuel pump and filter, MAF sensor, both post O2 sensors, EGR valve, crankshaft position sensor, timing gears and chain. Sometimes switches from P0300 code to P0305. The manifold gasket is showing a leak. Any ideas?


... 1996 GMC Sierra

2008 gmc sierra 1500 crewcab. the Service traction control,, service Stabilitrak,, engine power reduced and sometimes it adds Oil Pressure low-stop engine. i have bought the truck in one dealer changed the fuel pump the codes came back.. another said it was the sensor in the fuel tank, another changed a electric module. the code always come back. i have been fighting this problem now for about 7 months now. 5.3 liter engine flex. thanks..


Hi,\015\012 \015\012A vehicle may be brought into the dealer for a reduced power message, and DTCs P0120, P0220, P1516, P2101, or P2135.The Throttle Actuator Control ( ... GMC Sierra 1500

I changed the plugs and plug wires on my 96 GMC Sierra SLE 5.7L yesterday. Now my OBD scanner shows catalyst and EGR test as not completed or failed. No actual codes. When I first ran the scanner a couple of weeks ago, it showed no failures, no codes. Did I screw something up?


It can be possible that catalyst converter and egr were going weak and got faulty.But this does not necessarily mean the Catalytic Converter is bad!. Either Converter operating below efficency or Converter operating b ... 1996 GMC Sierra

Transmission Identification I see so many different GM trannys out there, but which one is right for a 1994 GMC Sierra SLE 4WD automatic extended cab short-bed gas 5.7 liter engine. The guys at work (Toolmaker) tell me that any 700R4L60E transmission will work


If it's a 1500 then yes the 4l60E tranny is for you. If it's a 2500-3500 you'll need a 4l80E. The 80's are only used in trucks with a gvw or 7200 and greater. ... 1994 GMC Sierra

I have a 1995 GMC Sierra very low on power I have did the checklist I think plugs plug wires fist cap rotor button checked codes only 1 idle speed sensor vacuum leak was problem checked fuel pressure 14 pounds continuous changed fuel filter pressurized fuel lines with seafo cleaner then changed out TBI TO A 5.7 liter TBI THIS DID HELP BUT NO EHERE NEAR RIGJT checked Egr cvp valve catalytic converter thinking it was stopped up sinse it has 140,000 miles on a G&M crate motor but conveyor had been


I think that you have started on the wrong foot and things have gone down hill from there. I suspect that the fuel manifold pressure is too low as it should be over 20psi for the injectors to work properly. The cat converters are not there to provid ... Cars & Trucks

2008 gmc sierra sle trouble code P1133


... 2008 GMC Sierra 1500 2WD

Color Coded, Electrical Wiring Diagram for a 1992 GMC Sierra SLE K3500


... GMC K3500

I have two DTC Codes PO 449 PO 455 - 2008 GMC Sierra 1500


... 2008 GMC Sierra 1500

1993 Repair manual for GMC Sierra 2500 SLE 2WD Pickup, 350 cid, 5.7 Liter


... GMC Sierra 2500

I have a GMC Sierra SLE K1500 5.7 liter Long Bed. It has several bolt on performance parts and a 3 inch body lift. (Recently Installed) The back up lights, turn signals and hazards do not work. First a friend told me that while i was backing up i had no lights on, as i was driving away from the shop i noticed my turn signal didnt work so i decided to attmept the hazards. When i pushed the hazard button it flickered once. I replaced the 30 amp fuse for the STOP/HAZ spot but there is still no


If you replaced the 30a fuse and it went out after it flickered once you have a short somewhere. You can use an inductance type of circuit tester to diagnose the location of the short to a general area of the vehicle to help pin point it much easier. ... 1995 GMC Sierra

P0305 Misfire code. This is on a 2001 gmc sierra 2500HD 8.1 liter V-8. So far I have changed out all the spark plugs and wires. Also put in new cam and crank position sensors as well as the #5 cylinder fuel injector. Checked the injector harness with a noid light and it seemed fine. I swapped coil packs to see if the fault went to a different cylinder and it did not. This misfire only throws a fault under heavy acceleration. The vehicle hesitates and can be felt jerking while under a load at aro


Check fuel pressure regulator for fuel in the vacuum line. ... 2001 GMC Sierra 2500HD

I need to know how much a total engine overhaul will cost, I want a brand new engine with 0 miles. I own a GMC Sierra 1500 SLE yr/2000


If you want a brand new engine with 0 miles, than you should buy a brand new one from General Motors thru your local G.M. dealer, what you spend there would be about as much as it would cost to have yours rebuilt. Also summit racing equipment sells n ... 1999 Chevrolet K1500

1998 GMC Sierra. Blower motor works sometimes. No particular circumstances, just when it wants to. Checked all fuses, relays, even replaced the resistor, nothing. Followed the wire harness and found the two pigtails that others have mentioned. Took the wires off, black and purple, and turned ignition on. Getting around 11 volts on all sittings except for the highest setting, it reads 0 volts. The compressor turns on at the console, all the switches on the console work, just not the fan.


Could it be the blower motor it self? sometimes they have a "bad spot" when it is not working, can you hit it and make it run? pretty common on these trucks. the switch is also common. they often melt at the connector on the back making a bad connect ... 1998 GMC Sierra

I have a 96 gmc sierra 5.7 liter and i put a new alternator on it 3 days ago and it was running fine then today i was running about 30mph and the voltage hand dropped to 0 and i went on for about ten min. then jumped back up to 14 volts ... any help will be appreciated


... 1990 GMC Sierra

I have 1998 sierra 1500 vortec 5.0 liters,when engine is cold (below 35 degre f )engine turn but don t start,i have fire,fuel pump run and i have pressure on my main fuel line juste before injector pack but dont inject fuel,if i plug block heater engine can start when is warm,and last time i start engine is missing and smell gasoline at exhaust pipe and very low power and i run the truck for 1 mile and the catalaser come overheat(red),i have two code when engine running(p1345 and other is missfi


Camshaft To Crankshaft Position Correlation Fault is what p1345 means. if the problem isnt electrical I would imagine the timing chain could be stretched and the engine is out of time somehow ... 1998 GMC Sierra

Wont idle Already posted this once and got a solution of MAF sensor but i got a OBD2 diagnostic tool and there are no codes being tripped/shown. I have a 1997 GMC Sierra 1500 5.7 liter V8. It will start and then die after 3 seconds or even sooner. I have already replace the fuel filter and relay. I have a car starter installed so i can crawl underneath and hear the fuel pump turn on when it starts, so i dont think its the fuel pump. Any answers will be much appreciated!!! Thanks!


Try the brake booster hose it might be sucking air ... 1997 GMC Sierra

1994 gmc sierra 1500 5.7liter code 12,43,82


... 1994 GMC Sierra

Hi i have a 2002 gmc sierra 5.3 liter engine i


Which o2 sensor did you replace? P0157 is low voltage - o2 sensor, Bank 2, sensor 2. So it would be the post cat o2 sensor on the passenger side. If you replaced the drivers side the code would still be there. ... 2000 GMC Sierra

Help needed on gmc envoy!!!!!!!? hello my friends gmc envoy was not starting i went to diagnose trouble codes i saw the engine check light on when i attached the device i didnt read any codes from the ecu saying there is no trouble code i asked him to unplug the throttle position sensor wire as he unpluged the wire one mor engine check light appeared on the dashboard it was a bit digger in size than the normal engine check light with arrow facing downwards.why is there two engine check light wat


Arrows pointing down is low coolant. If you\012can't read the code because it displays, "communication error", you\012have a blown fuse. Your ALDL may be tied in with the auxiliary plug. Look for a\012blown fuse and replace it.\01 ... Cars & Trucks

Hi I Need Some Major Help We Have A 2001 GMC W4500 With The GM 350 In It We Have Been Having Engine Codes Coming Up At Randon And When They Do It Runs Like **** We Can Erase The Codes And Will Sometimes Go Two Days Before Ever Putting A Pending Code in P0122 Throttle Position Sensor (Curcuit Low) Is Usally The First Code To Come Up But Not Allways It Has Been Changed And It Still Does It And Everytime It Throws Codes It Throws Differant Codes Under TPS Code But It Does Not Always Trow TPS This M


I would change the map sensor and the throttle position sensor and check the wiring while you're at it. \015\012\015\012I know it can be frustrating, but try that first. ... 2001 GMC Sierra 1500HD
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.2334 seconds