Having problems with your Ford Thunderbird ?

How do I remove the drivers side axle from a 92 Tbird?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Cv axle correct
Repair Help & Product Troubleshooting for Ford Thunderbird

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I remove the drivers side axle from a 92 Tbird?


Cv axle correct ... Ford Thunderbird

Hi, i have a 1995 toyota camry that i am trying to remove the driver side axle from the transmission. i hve tried wedging out with a crow bar, screw driver, my hands, and even tried tapping it with a hammer but it will not move. is there a way to remove the axle or a device that i can get to take out the axle?..


The strut needs to be removed/disconnected from the lower control arm. If this is not done you will not get the shaft out. The only way to get the cup to disengage from the differential in the gearbox is by brute force. It locates in the differential ... Toyota Camry

Wayne again with the front axle leak i removed the diff cover drained the oil, cleaned reinstalled and added 85 140 gear oil no leaks out of the diff. and no leaks out of the driver side for like two weeks, now it sprays all over the driver side wheel well and drips out of the tube that the axle slides into


There is a seal in the carrier .At the parts store ask for the carrier seals for the front differential.You will have to remove the axles,out of the differential,and the ring gear chunk,along with the carrier bearings,and install the seals from the i ... Dodge Ram 1500

How do you remove rear axle shaft to remove rear side axle seal on a2005 ford escape rear driver side what has to let go.


... 2005 Ford Escape

How do i remove the left (drivers side) cv axle on a 2001 volvo v70 xc. I have everything off. The axle is hanging out ready to be removed


This axle is held into the transmission by a circular round internal retaining clip called a "CIR" clip, they can be very difficult to remove and I answer this question often. \015\012Here is how you get the axle out, u must pull stra ... 2001 Volvo V70

How do you remove the axles from a 1996 integra? how do you pull them out? when i was taking of the left (drivers side axle) there seemed to a some type of mount with 2 bolts holding in the drive shaft, does that have to be removed too?


That sounds like the carrier bearing that goes to the axle. And yes it does need to be taken loose. \015\012\015\012Good Luck. ... 1996 Acura Integra GS-R

Tri-pot joint housing stuck on driver side of 2000 chrysler 300 m while removing cv joint axle shaft , outer and shaft removed iner tri pod joint stuck to axle shaft on trans. tried prying hammering heat , can not get inner clip to release housing for tripod joint


I have had this problem many times. I have always had to take the clamp off the drive axle boot near the transmission and take it apart there. I have never been able to get one off that did not pop off easy even after I had the transmission out. You ... 2000 Chrysler 300M

How to remove driver side axle off a 2006 passat transmission


... 2006 Volkswagen Passat

My CV axle is broke. I have everything removed but the axle wont pull out of the motor. The point where the axle enters the motor is set into a 2-3" recess and i cant get a bar / screw driver / or any other tool behind it to pry it out. I even built a tool that would reach in and hook the back side but still cant get axle to pull out. so far everyone keeps saying use a bar behind it to pop it out. as i said before that is impossible as it is recessed into the motor several inches. please help, i


Try wrappin a cable or chain around it where possible an get another to help yank it out if possible ... 1990 Geo Prizm

I'm replacing half shafts on 94 mazda 626 w/auto trans. Front end is off ground and supported. After removing drivers side axle shaft, I replaced it with a new one and while installing it turned it a little (enough to move wheel on passenger side). Am I in trouble because I might have moved differential side gear out of place? How do I know if I did? Manual says to use special tool so that diff side gear does move out of place, unfortunately I forgot this part while doing install.


Your okey\015\012You have to turn the new axle\015\012after you install it to check it out\015\012\015\012The other side is going to turn,\015\012if it didn't ,you wouldn't have the \015\012replacement axle even in ... 1994 Mazda 626

I have a 2006 Hyundai Azera and want to replace the front rotors. I cannot remove the front driver side. The two screws on the rotor would not even come out with an impact screw drive so i had to machine them flush with the back of the rotor. I hit the rotor to break them loose and it wouldn,t move. I tried a heavy duty puller and hit it with a hammer and still would not budge at all. I was wondering if i could remove the axle nut and remove the hub and place it on a hyd. arbor press to remove t


... 2009 Hyundai Azera

How do i remove the drivers side drive axle on AWD 98' Mountaineer


... 1998 Mercury Mountaineer

How to remove front driver side axle on 98 isuzu rodeo


... 1998 Isuzu Rodeo

CV axle removal & installation - driver side


... 2000 Chrysler Sebring

Removing front axle, driver side on Saturn 98 SL1 manual trasmision


... Saturn SL

2008 trailblazer driver side front axle removal is it come out like passenger side


... 2008 Chevrolet Trailblazer

I need to remove the outend of the drive axle and am having troubles getting the axle out of the hub. Every other place has indicated that it just slides nicely out with little or no force. However on this vehicle that is not the case. Could there be something that I missed or is this just stubborn. It is on a 2001 Kia Rio driver side axle with a standard transmission.


Put the axle nut back on backwards (flat side out, so flat is even with the axle end...give it a sharp blow with a decent sized hammer and it will break loose. ... 2001 Kia Rio

I am changing the drivers side carrier housing! I pulled the wheel, and c.v. axle, I removed all of the bolts holding the Housing to the engine, and removed the driveshaft. It will not fit through the hole above the frame, and I can't squeeze it through the bottem past the engine!! How do I remove this part???


You will need to remove the steering rack,frame crossmembers,and motor mount stud nuts.then CAREFULLY lift the engine up by the oil pan with a jack.The jack must be positioned on the passenger side of the oil pan.Or you can remove the oil pan. ... 2003 Chevrolet TrailBlazer

Front axle 1984 ranger 4x4, drivers side front axle broken. i have the everything removed to axle, but it will not come out. is there a clip further towards the front differential? also ,where can yo


... 1983 Ford Ranger

Front drivers side axle removal


There's not any special tools. You need a socket to fit the nut on the end of the axle and a wrench to take the nut and bolt off the bottom ball joint that slides through the control arm. Take a bar, pry down on lower control arm, pulling ball join ... 2003 Dodge Neon

I need to remove the front axle out of the differential on a 2003 Dodge Ram 1500? What is the best way to pull it out. I already have the half shaft taken off I just cant get the solid axle out of the differential. Its on the driver side.


When removing the front axle i believe that you must open the front differential cover and inside the dana you will see a small 8mm bolt located on the spider gear center it holds the pin bar in place and the pin bar holds both the upper and lower ge ... 2004 Dodge Ram 1500

I removed knuckle/hub assembley and axle from driver side of 97 Honda Accord. The drive shaft will not disengage from the hub and rotor,even with the assembly in a table vise. I've tried spraying BP blaster into the spline of the shaft on the outer cv joint.This shaft is stuck and not moving. I need to remove the old hub barring to install a new hub barring.


You will need to shock the shaft to break the internal rust that is holding the two peices together\015\012Since you have a vise do this\015\012have the shaft tightly secured into the vise, and not the cv joint\015\012have a large p ... Honda Accord

I have a 2004 ford expedition and i need to remove the front driver side axle what is are star looking nuts and what do i need to remove them


12 point wrench/socket ... Ford Expedition

The driver side axle does not want to come out of the transmission I have taken the right side out allready and it will not come out, I have tools to remove the thing, but it will not come out...


Just be pacient with it and make sure all the splines are lined up and double check to make sure there is not that one stray component holding it in ... 1998 Ford Escort

What is the procedure to replace the drivers side axle (CV joints)on a 1999 Chevy Cavalier. I have the new axle just need the remove and replace procedure


You don't need the special tools that they use in this procedure, you can use a hammer and a block of wood to get the axle out of the hub and you can use a pry bar to get the axle out of the transmisson.Notice ... 1998 Chevrolet Cavalier
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.8866 seconds