Having problems with your Ford Mustang ?

How to replace rear axle on 1998 ford mustang

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Ford Mustang

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cost for replacing rear axle 2001 mustang - 2001 Ford Mustang


... 2001 Ford Mustang

How to replace rear axle on 1998 ford mustang


... Ford Mustang

I will be replacing the rear wheel bearings for a Ford XA GT 9inch disc brake rear end. I would like to understand the configuration of the axle assembly and how to replace the rear wheel bearings.


... Ford GT

I am doing a brake rebuild on my 97 ford F-150 4.6, rear drumb system with ABS and I am looking for a ford diogram, I have a chiltons but it is generic. can you help ? also there is a hydraulic union mounted on rear axle housing, which marries front line to rear brake lines [ 3 way ] which needs to be replaced. how or where can Ifind this ? I have looked all over the web and have not found so far. [ brass ]


There really shouldn't be any issue with that rear union that a little brake parts cleaner couldn't take care of. All it is, is a "T". Is it really necessary to replace every component? Was it driven into a river? The only things you should have to r ... 1997 Ford F150 Regular Cab

How to replace the rear end fluid on a 03 Ford, Mustang?


... Cars & Trucks

How to change rear axle on 1998 Ford mustang - 1998 Ford Mustang


... 1998 Ford Mustang

I have a 1988 ford thunderbird standard coupe 5.0 liter engine with digital speedometer. I performed a cobra brake conversion on the car from ford motorpsort, and replaced original 2.73 rear end with a 3.33 traction lock axle. I replaced the original 215/70r14 tires with 245/45zr17 tires. the tire diameter for the 215's was 25.9inches, whereas the tire diameter for the 245's is 25.7inches. With this little bit of difference, i can't figure out why my speedometer is reading 15mph higher than


You're going to need to increase the tooth count on the driven gear on the speed sensor. probably with 3 additional teeth in the count. \015\012\015\012 ... 1988 Ford Thunderbird

I need to replace a rear axle seal on a 98 ford explorer. How do I remove the rear axle?


Unbolt it,bolts on end of housing ... 1998 Ford Explorer

Rear axle mount specs for 2000 Ford Mustang - 2000 Ford Mustang


... 2000 Ford Mustang

Replace left rear axle seal 1999 ford explorer


\015\012Axle Shaft \015\012\015\012Removal \015\012\015\012Raise and support the vehicle. For additional information, refer to Section 100-02 . \015\012\015\012Remove the wheel and t ... 1999 Isuzu Rodeo

How do you replace the rear axle bearing on a 1997 Ford Econoline Van?


... Ford Cars & Trucks

Replace rear axle seal on 1997 f250 super duty ford


... 1997 Ford F250 SuperCab

How to replace gears in rear axle assembly of 1999 ford explorer


... Cars & Trucks

How to replace rear axle seal on 1994 ford f150


... Ford F-150

How do you replace the rear axle bearing in a 2006 ford explorer


... 2006 Ford Explorer

Replacing rear axle seal and bearing for 97 ford explorer


Here is a guide on how to change the rear seal and bearings on a ford mustang http://fhmotorsports.blogspot.com/2013/07 ... 1997 Mercury Mountaineer

1999 mustang rear wheel bearing replacing - Mustang Ford Cars & Trucks


... Ford Mustang

Have 1994 ford ranger xl and need to replace right rear axle & backing plate. cant get small bolt out of 3rd member that holds in pin for spider gears so axle can be slid in and keeper removed, its now stripped, how do i get it out and is it left or right hand threads ?


IT IS RIGHT HAND THREAD, HARDENED, WITH LOCTITE FROM THE FACTORY. LOTS OF HEAT AND A VERY GOOD SET OF VICE GRIPS. GET IT RED HOT THEN CLAMP THE VICE GRIPS ON THEN TAP V/G WITH HAMMER TRYING TO BREAH THE LOCTITE FREE.ONCE YOU GET THAT LOCTITE BROKEN I ... 1994 Ford Ranger Supercab

Replace 2000 Mustang rear shocks - 2000 Ford Mustang


... 2000 Ford Mustang

Remove rear posi axle 1995 mustang - 1995 Ford Mustang GT


... 1995 Ford Mustang GT

Want to replace rear axle seal on 2000 ford expedition i have removed the 4 nuts and bolts that hold the back plate on but not sure how the axle comes out


I have problem with my car ford expedetion air suespention syestem some time it is not work \015\012 ... 2000 Ford Expedition

I have a Jeep Wrangler 1992. Replaced rear axle with a Ford 8.8 axel rear end and installed all new brake rotors, callipers, hoses, metal lines, forward brake discs, hoses. Have bled reapeatedly....pumping and numatic suction brake bleeders. Still no brakes. Will not build up pressure. Wondering about the prop. valve? Opened it and cleaned it...looks fine. I think brakes work fine...wife disagrees. Unable to get brakes to bleed could the prop. valve be to blame. Followed all instructions in Hane


The proportioning valve most definately can be the problem. Did you change it or is it the original? (A disc/drum system uses a 70%front/30%rear braking ratio, whereas an all-disc system is alot more even). I would first bleed the master cylinder. ... 1992 Jeep Wrangler

07 ford mustang gt MAKING a whining like tire but louder noise from the rear when crusing just had the rear differential gear replaced and housing


Do you know if the correct fluid (plus the required friction modifier) and fluid level were used? I'd take it back to where you had the work done and have them take a look at it and confirm the above if you don't know. If the above is correct, I'd ... Ford Mustang

95 ford explorer rear axle seal replacement - 1995 Ford Explorer 4.0


... 1995 Ford Explorer 4.0

My rear axle split in two on a 2001 Windstar. What is the proceedure for replacing it? I have tools, jacks, jackstands, etc. Do you know where to get a new replacement besides Ford?


... 2001 Ford Windstar
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.3137 seconds