Having problems with your Ford F-350 Super Duty ?

Weel seal rear F 350 2006

\015 How to replace the weel seal rear\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

You have to pull the rear axle, open the rear end and pull the clips or bolt for that axle ane pull the axle out then take a screw driver and pop the wheel seal out, just tap the new weal seal in with a hammer carefull not to bend it and then put the axle back in and the bolt or clips
Repair Help & Product Troubleshooting for Ford F-350 Super Duty

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can you replace a 2 piece rear main seal crankshaft with a 1 piece rear main seal cranshaft


I doubt it. The one piece uses a different lip, and it would be tough to get the one piece in the groove in the block while holding the crank too. ... Cars & Trucks

1. Need to know how to disassemble the 4X4 front hubs to replace rotors in a 1993 Toyota 4X4 small pickup truck. 2. I am also replacing clutch, pressure plate, throw-out bearing, and ffy-wheel. I need to know how to replace the rear engine crankshaft seal while I have the transmission out, because I have a rear seal leaking oil...


... 1993 Toyota Pickup

2005 town and country rear ac line removal behind rear wheel . I have a leak at the fittings under the van behind the right rear wheel. I suspect a seal but cannot remove the lines. there is 1 nut which holds a plastic retainer on a center bolt that has a torx head. Is there a special tool or technique involved in removing the retainer?


... 2005 Chrysler Town & Country

I have a 1993 buick roadmaster with a rear main seal leak. I like to know if it a 1 piece seal or a 2 piece seal?


... Buick Roadmaster

Weel seal rear F 350 2006


You have to pull the rear axle, open the rear end and pull the clips or bolt for that axle ane pull the axle out then take a screw driver and pop the wheel seal out, just tap the new weal seal in with a hammer carefull not to bend it and then put the ... Ford F-350 Super Duty

Replace wheel seal on a2004 chevy 1 ton dually rear


... Chevrolet Cars & Trucks

I have a 1986 gm motorhome, with a P 3500 (1 ton) chassis, disc brakes all around. I have had issues with the back brakes "sticking" slightly on, resulting in a wicked metatl overheat smell and extreme heat on the rear brake components. The front brakes work and "ride" properly. I have had the whole back end done, (New axle seals, diff seals, calipers, rotors, and pads, done. The problem does not go away. It seems after about twenty minutes of driving, the brakes do not want to fully release on


Sometimes the rubber brake hoses will collapse internally and allow fluid to pass through to the caliper, but won't let the fuild return. The best way to check them is to crack open the hoses where they go into the caliper. If they squirt, then ther ... 1986 Chevrolet Camaro

My 1996 GMC Sierra with 330,000 miles on it is struggling going from 1 to 2nd gear. I am loosing fluid at the rear trnsmission seal. There is a slight whine. Do you think fixing the seal will eliminate the problem ?


That's a lot of miles on that transmission! The short answer is "no". Replacing the seal will stop the fluid leak, which should be done. However, the whine is an internal mechanical problem, quite possibly from the rear output carrier which commonly ... 2000 GMC New Sierra 1500

Is the rear main seal on a 1999 gmc yukon a 1 piece or 2 piece seal. Leaking oil real bad from back of motor.


Its a one piece. should be the metal one with the rubber inside seal. of corse you gatta pull the tranny but its a good time to change fluids and maybe slap a new torque converter in. changing the rear main is pretty easy after the tranny is out. ... 1995 GMC Suburban

Ihave whaat smells like rear end fluid coming out behind both rear wheels about 2 weeks ago it was only on 1 side (passanger side) so i replaced the wheel seal and now both side are leaking what could that be


... 2003 Chevrolet Silverado 2500HD

How do i know if i have a 1 pc rear main seal or a two pc seal on my 1991 mustang 302


You have a one pc rear main seal,You will have to remove trans,from the car to install the rearmain seal.Check freeze plugs,and cam plug for leaks also,while you have the trans out.Also make sure the crank shaft is not damaged with a roove cut in it ... 1991 Ford Mustang

Clicking sound coming from right rear area next to 3rd row seat whwn rear heat fan set to 0,1,2 or 3..


... 2004 Chevrolet TrailBlazer

1981 f100 2wd auto rear main oil seal is leaking. How do I get. To it once I back the transmission out is it a 1 piece. Or 2 piece seal


Remove transmission. seal is behind drive plate (what in manual trans vehicles is called a flywheel. You really need a $25 service manual when you do this kind of repair yourself...most likely a 2 piece seal in that truck...depends on motor ... 1981 Ford F 100

Rear breaks lock up at slow speeds. when traveling from 0 to 10 MPH if breaks are applied abruptly 1 or both of the rear wheels will lock up before the front breaks seem to engage, especially on wet road. This is vary dangerous and on wet road can cause loss of vehicle control. At higher speeds around 35 and up when breaks are applied abruptly the vehicle will swerve to the right just for a split second then straighten out. In both cases if the break pedal depressed one or more times prior to


`right one of two problems ,firstly remove the rear drums and check for a fluid leak as a slight smear of fluid will cause the exact problems you describe ,if the rear shoes are dry then push the cylinder each side to make sure its not seized ,second ... 2001 Mazda Tribute

I fitted a rear crank oil seal on to a VW CADDY, and was wondering if you had to set the magnetic ring for the crank sensor up in a certen way, because i hav changed 1 and put it back together and it wont fire when turning over.CADDY PN56GHV DIESEL.


The sensor needs to be set to the ring. There sholud be an extremely minimal gap between the sensor and the ring. ... 2001 Volkswagen new Passat

How to replace rear main seal on a 2006 Mitsubishi Galant 2.4 liter engine. Please give me any information you have on this I.E 1 or 2 gaskets, diagrams, pictures... Thank you.


... 2006 Mitsubishi Galant

Is the rear main seal a 1 or 2 piece? can u just drop the oilpan?


You must pull trans or engine.. should be one piece... ... 1990 Chevrolet S 10 4WD

What can be used to stop the rear main seal from leaking? it is leaking approx. 1 qt. every thousand miles


... 2002 Cadillac Deville

1999 Plymouth Neon 2.0 single overhead cam (Automatic)- A friend dropped my transmission to replace the rear main seal. It's all put back together and the gear selector only locks in park now. I took it out of park by hand and notice that it does not set into any other gears(R,D,2,1). Just park and neutral. It just has play when out of park. This tells me it's something internal. Could it be from the torque converter not in right or what? The gear selector on the transmission itself was not touc


Was the bolt tightened that holds cable to transmission have seen this overlooked have someone shift while you watch the cable ... 1999 Plymouth Neon

What fluid type waitise do i need for the rear and witch seal do i need 1 piece or 2 pice


The rear differential uses GL5, or 85W90 weight gear lube.\015\012 The gasket is a piece design.\015\012Good luck ... Chevrolet C1500

1995 f350 ford 2 weele drive dually rear drum removal.....do I gotta pull axle? Do I gotta replace seal?


Unfortunately you will have to remove the axles on that model of truck to access the brakes and it is necessary to replace the seals at this time because you will probably cut the old seals upon removal.I would recommend that if you are ... 1995 Ford F350

Replace rear crankshaft seal for 2002 nissan liberty problem turn up not changing gears drives only 1 gear


... Nissan Maxima

My cam shaft timming gear and my crank shaft timming gear dots line up and my harmonick balancer timming mark is on 0 which way should my rooter button face towards number 1 or towards rear of engine


The rotor should be pointing close to number 1, but keep in mind that the spark is actually supposed to happen before the piston gets to tdc so the rotor will be a little bit past the number 1 terminal when the crankshaft indicates that you're at tdc ... 1994 Chevrolet K1500

Dealer indicated the rear main seal is leaking. He quoted more than one day of work and $1,200. Is this reasonable? This seems very expensive and odd that he could so quickly diagnose the problem.


Yes This IS EXESSIVE It Calls for Transmission Removal BUT The PART is Only Around 10-30 $$ Labor Should be Around $600.00 ... 2002 Toyota Highlander

1 ton dually rear axle seal - Cars & Trucks


... Cars & Trucks
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.1825 seconds