Having problems with your Chevrolet TrailBlazer ?

How to replace ball joints on 2003 trailblazer

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Chevrolet TrailBlazer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 2005 Trailblazer. I have had the stalilizer bar replaced, new ball joints, greesed the fittings on the ball joints. New calipers, rotos and branke pade. HOWEVER, I still have a clunking sound which seems to eminate from under the drivers side floor board.The technician told me that the suspension is great and can figure it our.. Any ideas?


If the changed the sway bar did they change the front sway bar end links? These clunk really bad but because the pressure the sway bar puts on it, it feels tight until you remove them. I have changed several. Works every time front and rear clunking. ... 2002 Chevrolet TrailBlazer

Need to replace the lower ball joints in my 2002 Dodge Durango SXT. Receiving conflicting advise. Some say that I have to replace the whole control arm with new ball joint. Others say that I can press the old ones out of the control arm and press new ball joints with grease fittings up into it... the existing ball joints are factory and do not have grease fittings. I can't be sure, but it looks like the top of control arm that houses the ball joint is solid cast. It doesn't appear to be a "hole"


It looks like if you buy the joint from Chrysler then it comes complete with the arm however there are aftermarket companies that make just the ball joint which can be pressed in and out. It's fairly common for a manufacturer to offer the joint only ... 2002 Dodge Durango

3.3 2001 Dodge Caravan ball joint. Have clunk noise on bumps. Pretty sure its a ball joint but have not put it in the air to unload suspension. My question is it a press fit ball joint? Also, will I need a separator and a Ball joint kit? Any other tools that may be required for replacement? Any suggestions or steps for easier replacement?


Just checking, have you looked at the sway bar links. Its a common problem on these cars, has similar symptons, and is a cheap fix. $30 for parts for both sides and about 30 mins to replace. ... 2001 Dodge Caravan

What is the process of replacing the upper ball joint of 72 chevy nova. Do you have to press the upper ball joint in, like the bottom ball joint. What tools do you need in replacing the upper ball joint. Thanks


If you are replacing with new....you have to grind off the old if it is rivited in...to install...it's new hardware and it is BOLTED in. No special tools. ... Chevrolet Nova

Power steering makes noise while turning left & right even after replacing ball joints, CV joints & entire steering box without power pump. what could be the remidial measures? though I have replaced the steering box for making the suspension more stable. Before replacing the steering box the power pump sound was there but not so prominent.after replacing steering box, ball joints & CV joints & after driving for several days the steering become easier & power pum noise became less hearing. But n


... 1997 Toyota Corolla

Step by step how to replace ball joints on a 04 chev trailblazer 4x4


... 2002 Chevrolet TrailBlazer

How do i replace the upper ball joint on a 2002 trailblazer


... 2002 Chevrolet TrailBlazer

What tools do you need to replace ball joints in a Trailblazer.


... 2003 Chevrolet Trailblazer Ext

How do i replace the lower ball joint on a 2006 polaris trailblazer


... Cars & Trucks

How to replace ball joints on 2003 trailblazer


... Chevrolet TrailBlazer

How to replace ball joints in 2006 trailblazer


... 2003 Chevrolet Trailblazer Ext

How to replace an upper ball joint on a 2003 trailblazer


... Ford Cars & Trucks

How to replace upper ball joint on 06 trailblazer


... 2003 Chevrolet Trailblazer Ext

My Tahoe has some play in the steering. I took it into an independent garage and was told the pitman and idler arms needed replacing. Knowing I could do the work myself, I drove the beast home and crawled under it to take a look. Everything but the ball joint on the pitman arm looked fine. Some grease is coming out of the ball joint, so I am sure it will need replacing. The ball joint, is not causing the play in the steering. When I move the steering from one side to the next, to check play,


Hi Jeff,Play in steering is compounded by each weakness, no matter how slight, that exists in the entire steering linkage. I admire your technique in troubleshooting. You definitely make valid points with your observations. ... 1997 Chevrolet Tahoe

How do I replace the upper Control arms on My 1979 chevy 1/2 ton pickup. I saw a replacement control arm that has the bushings and ball joints already installed. I'm trying to save the high labor cost that this involves. I can replace the ball joints myself but I know that you need special tools to replace the bushings. Would I still need to try to get this tool since the new upper control arms have them installed already?


Since the new arm comes with the bushings, there is no reason to get the tool to install them. Upper arms are relatively easy to install...just a bolt out, bolt in operation as the springs aren't involved. Support the suspension under the lower contr ... 1978 Chevrolet C1500

Continuation of 1998 Plymouth Breeze Stiff Steering Issue Well, we ended up replacing basically all of the front end of this 1998 Plymouth Breeze because it was totally worn out. We replaced the front motor mount, the rear motor mount, upper ball joints, front struts, both CV axles, both control arms (lower ball joints), the Rack & Pinion and Tie Rod ends We even replaced the water pump and timing belt because the water pump was leaking and since we had it open, we replaced the timing


First, the mechanic has no idea what that switch is most likely. I have several Rack and Pinions for dodge and Plymouth vehicles and none have any electrical on them however I have seen some that do and having looked at these I'm pretty sure it is a ... 1998 Plymouth Breeze

Do Can you just replace ball joint or the upper arm assem?how to replace rear upper ball joint on 1996 Accord


... 1996 Honda Accord

When replacing the ball joints in the front of a '96 Volvo 850 GLT can you just replace the ball joints or do you have to replace control arm or strut???


It comes as one whole piece and i just searched around for a control arm that might have removable ball joints, couldn't find one its one solid piece. Makes it cheaper for you but in all reality, you get a lot better of a product and it does keep the ... 1996 Volvo 850

Upper right ball joint replaced only 2 weeks ago along with u-joints. Garage says now upper right ball joint is riding up and cannot be seated properly. The car is now unsafe to drive with this issue? Can this be fixed without replacing the whole front end? Thanks, Dan


... 1995 Jeep Grand Cherokee

I have a 2007 dodge ram 3500 and when i turn hard right and then hard left the steering binds in the middle and then turns. replaced gear box and power steering and ball joints have been replaced. the ball joints have been replaced 3 times in the last 2 months due to difective parts.


... 2008 Dodge Ram Pickup 3500

How do I replace a ball joint that's going bad on the lower front right control arm. The car is a 2006 Nissan altima 4 cyl. Front wheel drive. Is it possible to replace the ball joint instead of the whole lower control arm itself? If not, how do I replace the lower control arm on a altima. Is it different from front wheel than rear wheel drive? Thanks.


To replace a ball joint with the lower control arm, use bolt breaker spray (PB blast) Remove the cotter pin and loosen hub lock nut and wheel nuts (use long breaker bar) Jack up car and remove wheels. Remove outer tie rod cotter pin and crown bolt, p ... Nissan Altima

Need to replace lower front ball joints on a 99 Acura TL. My personal mechanic wants me to get the ball joints from the Acura dealer--who wants $205 each and includes some kind of arm with the ball joint. I prefer a $40 or less ball joint only from other parts sources. Which should I use?


The ones from the dealer is a ball joint and the control arm which come together with the ball joint already press in one whole piece meaning less work to do. just a simple swap in swap out. The $40 from parts stores or parts source is just a ball jo ... 1999 Acura TL

2000 lincoln ls bad ball joints! should i replace whole knuckle or just ball joints


Yes you can buy just the ball joints ... 2001 Lincoln LS

What is the process to replace the ball joints in my 2002 acura tl type s? what steps are involved? will i need to replace anything more than the ball joints?


The upper ball joint is an integral part of the upper control arm and the lower ball joint is an integral part of the spindle. ... 1999 Acura TL

2004 Pontiac Montana, can you replace the end fitting on the shift cable or do you have to replace the entire cable? The end fitting that clips onto the ball joint on the transmission shift selector has broken and comes off of the ball joint. Is there an easy repair?


You have to replace the entire cable. ... 2004 Pontiac Montana
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.2418 seconds