Having problems with your Chevrolet Cars & Trucks ?

03 silverado 6.0 oil sending unit replacement

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Chevrolet Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where can I find or download a pdf Service Manual for a 2006 Chevrolet Silverado 2500HD, 8100 Gasoline Motor with Allison transmission? The oil pressure gauge stopped working and I am fairly certain it is the oil sending unit that needs to be replaced but on the 8100 motor it's not a typical sending unit, or so I am told. Is it loacted next to the distributor, screwed into the head just below the manifold on the drivers side of the block?


Those are sold on ebay in book for and on CD. ... 2006 Chevrolet Silverado 2500HD 2WD

2005 chevy silverado 1500 4x4 5.3L low oil pressure comes on and there's a ticking noise. I changed my oil, oil filter and added rislone to help change the oil. I replaced the oil sending unit and my truck still saying low oil pressure and the noise is getting louder. What should I do next. Change my oil pump??


... 2005 Chevrolet Silverado 1500 2WD

I replaced a oil sending unit on my 89 vw fox,because the old one was leaking. the new one setts the dash low oil lite on. i put the old one back in and the lite goes off. i went back to autozone for a replacement &it also makes the lite come on. there are only two types of sending units for this yr. the other one has too big of threads to fit my fox! my sending unit screws in right on top of my oil filter!HELP


The ones you bought probably were the versions that screw in the cylinder head. Get something like the third one from herehttp://www.partstrain.com/ShopByDepartment/Oil_Pressure_Switch/VOLKSWAGEN/FOX ... 1989 Volkswagen Fox 4 Door

1990 chevy 1500 4/4 half ton wipers don't work? I burnt up wiring on my 90 chevy silverado with carb back fire. Replaced wiring with 1989 chevy same model all plugs matched up except oil pressur switch has 2 prongs 90 chevy has 3 prongs, took sending oil unit off 89 and put it on my 90. Only one more difference was gray wire on 90 by computer plug 89 did not have this and 89 had a red and white wire that does't do any thing on the 90 but 89 had it. My problem is when i turn on the wiper motor th


Your best bet here is to go to the dealer or a reputable tune up shop and see if they will provide you with wiring diagrams for both years. If you explain your predicament, they will most likely give them to you.They don't like to tackle these kinds ... Chevrolet Silverado 1500

On my 2003 Silverado 3500 diesel the oil pressure guage reads zero. I've replaced he sending unit on engine and it still reads zero. I think I may need to replace the whole instrument cluster. if so, where could I purchase one?


Try replacing the stepper unit. the cluster pulls out in minutes. desolder the old stepper unit and solder in the new unit ... 2003 Chevrolet Silverado 3500

Oil Sending Unit 1996 mustang 4.6 sohc replacement oil sending unit to replace 0rg. to a varuiable ohms unit and remove resistor and jumper it and the oil gage will now vary to the pressaue of eng.


... Cars & Trucks

I was told I need to replace the oil sending unit on my 1994 Jeep Cherokee Country. I bought a Haynes Repair Manual, but I have not been able to find where the oil sending unit is located, or how to replace it. Do I need a special tool to replace the unit?


The switch is near the oil filter. It can be done with a pair of channel locks or pliers or a deep well socket if you have the correct size. If using pliers make sure you latch on to the metal part near the base. ... Jeep Cherokee

How to replace oil sending unit on 2003 chevy silverado


... 2003 Chevrolet Silverado 1500

03 silverado 6.0 oil sending unit replacement


... Chevrolet Cars & Trucks

How to replace oil sending unit on 2003 chevy silverado 1500


... 2003 Chevrolet Silverado 1500

2001 Mercury Mountaineer oil sending unit replaced twice, oil gauge replaced and gauge still does not work. where should i look next


For oil not working check the help link shown below:-----Oil Gauge\012and Temp Gauge Not Working?\012\012 \012\012 ... 2001 Mercury Mountaineer

I keep getting a stop engine low oil pressure warning on my 1996 Cadillac Sedan Deville . I just changed the oil and filter.Do I need to replace the oil sending unit and where is the oil sending unit located .


Just wondering if you put in the correct amount of oil and tightened everything back up properly... ... 1996 Cadillac DeVille

I have an 1994 Plymouth Voyager with the 2.5 an i went to put a oil presser gauge in an i did but after a some time the car running the car died will not start the key comes on an turns over but no spark an it dont sound like fule pump is working i no for a fact that the coil ant gitting no power . i think because of the oil sending unit being out somthing told the computer that there ant no oil presser so it kicked off but im not sure .i replaced the sending unit (oil) u think im going to try t


The oil pressure sensor can't shut it down on this model. Have you checked the timing belt? ... 1994 Plymouth Voyager

I have a 98 dodge ram 1500 5.2L. The oil sending unit only worked intermittanly so I replaced the sending unit. It is a real bear to get to and I could not get the connector off before unscrewing the sending unit. After I unscrewed the unit I disconnected the connector and then connected it to the new sending unit. I could not reuse the little red connector lock. But it shouldn't need it because it still has the regular connector latch. Anyway now the guage in the truck is maxed out when the tru


Could be a bad sending unit. I had that happen to mine and I had to put 3 in it. ... Dodge Ram 1500

Oil leak between oil sensor sending unit and oil filter hold on location. is there a gasket to replace or does the whole unit need to be replaced


... 1996 Volkswagen Jetta

I have a 99 Jeep Grand Cherokee 4.7 oil pressure reads 40 at idle and drops to 0 when given rpms. Pull pan screen was clean. Noticed oil sending unit was leaking, I replaced it. I still have the same problem. Help! Could it be the oil soaked sending unit plug?


I just had the same problem with a malfunctioning gauge with a very oily sending unit. I went to Oreilly's auto and got a replacement sending unit for $38 and put it in and got the same results you did. I would have 40 psi at idle and it would drop t ... 1999 Jeep Grand Cherokee

2004 Ram V-6 3.7 Liter. Start truck oil pressure gauge stays at zero. Shut it off and re-start and gauge works perfect. It only acts up at first start up. I purchased an oil pressure sending unit for the problem and went to replace it but then the plot thickens. Next to the oil filter is a sending unit that looks like what I bought from Dodge dealer how ever I wasn't able to get the connector off yet but there is a purple wire that goes into the end of the connector and it is cut off and wire is


To diagnose this properly and get all the information on locations your best bet is to go to mitchell1diy online and pay the 12 bucks for the info. I doubt this is a sensor issue. Its most likely a instrument cluster or computer problem. ... Dodge Pickup

1995 GMC YUKON V-8 5.7 TBI I HAD THE OIL SENDING UNIT CHANGE OUT AND KNOW WHEN ON THE HIGHWAY I HIT THE GAS AND THERE NO POWER IT LIKE THE OVERDRIVE GEAR IS DISCONNETED THE SO CALL MANCHIC AT VIP AUTO TOOK THE WIRE OFF I DONT KNOW IF HE PUT THEM BACK ON RIGHT OR IS MY OVER DRIVE UNIT GONE HAD POWER BEFORE I HAD THE OIL SENDING UNIT REPLACED ANY HELP PLEASE I NEED TO US THE TRUCK ON THE HIGHWAY AND I CANT BECUSE I CANT GET ANY POWER OR SPEED OUT OF HER .......


... 1995 GMC Yukon

I have a '99 Ford Taurus with 178K miles. The oil light came on while I was driving the vehicle. There was oil in the vehicle. I have replaced the oil sending unit and the oil pump strainer has been cleaned. The engine is not tapping. I have been told two different solutions: replaced the oil pump and replace the engine.


No! If the engine is running fine and sounds normal the light might be coming on for some other reason. If you remove the wire from the sending unit does the light go out? That wire if it contacts ground anywhere it'll turn the light on. Melted to ... 1999 Ford Taurus

How difficult is it to replace the oil sending unit?


Not hard located at top rear of engine by firewall small black cylinder ... 2003 Chevrolet Silverado 1500

Location of oil pressure sending unit on 3 8 engine, on an 1986 Oldsmobile brougham? Also I am replacing the radiator which had a disconnected, what looked like a cooling sending unit located on the side of the radiator? Is this where the cooling unit sending unit is located? My cooling fan does not appear to be working properly, so I would like to know, if I can straight wire the fan motor with a toggle switch, by bypassing the relay? I am attempting to install a set of gauges mounting insi


... 1986 Oldsmobile Regency

Where is the oil sending unit located on my 1998 Ford Expedition 5.4 Litre? The dash oil sensor keeps going on and off and my best guess is that I need to replace the sending unit.


... 1998 Ford Expedition

Alrighty. I've asked this a few times before, I have more info now. CHEVY 350 K1500. 1993. Replaced intake gaskets, (bad oil leak) dropped a small amount of coolant in with oil while doing so. Changed oil before starting truck. Since then the pressure will read fine while cold, but as the truck warms up, the pressure drops, eventually all the way to zero, and will stall the truck at idle. I've replaced Sending Unit, Oil Pump, Oil Screen, Cam Bearings, Mains/Rods Bearings. and about 5 oil change


How did you clean the gasket off of the head? if you used a sanding disc the grit will eat up the bearings. are you reading pressure with a mechanical gauge? you have replaced all bearings??\015\012\015\0126 psi @ 1000 RPM18 psi @ 2 ... 1993 Chevrolet K1500

2006 Xterra. Low oil pressure gauge at idle to normal when driving. Manual testing indicates all is fine. Oil sending unit replaced. Digital instrument panel replaced. Oil level fine. This car is babied! I'm $1K in for parts/labor so far. Could this indicate a replacement of the timing chain case cover seal that I've read about? Any suggestions on what else this could be?


... 2005 Nissan Xterra

Oil pressure I have good oil pressure but once it warms up the gauge clicks clicks clicks fluctuating, then it bottoms out. Engine still sounds strong, with maybe a little tapping when oil pressure is bottomed out. replaced sending unit, hooked external gauge and it is showing low to no oil pressure, had it in 2 shops, one couldnt figure it out other just wants to replace with a new engine at a cost of 6000.00 plus. two shade trees told me to change oil pump, a third says to check the pan for a


The oil pump pickup could have come off the oil pump, but u could fell it inside the pan through the drain plug, that is possible, but not very likely, try installing an aftermarket high volume oil pump, most ar ... 2003 Ford Ranger Regular Cab
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.8451 seconds