Having problems with your BMW Cars & Trucks ?

How do i replace the distributor cap and rotor on a 1987 bmw l7

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for BMW Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

P1345, won't start, sputters and snorts when cranking starter. on a 2000 chevrolet astro awd. prior to present problem, replaced timing chain, spark plugs, distributor cap and rotor. it started and ran fine but ses light remained on. kicked out a p0340. pulled the distributor cap and rotor, checked the screws holding the camshaft positioning sensor, and returned the cap and rotor. it wouldn't restart. replaced the camshaft positioning sensor and reset the pcm trouble code memory. then it


P1345 code problem:------\015\012\015\012This\015\012code is set when either the CAM\015\012sensor is not in it's correct position, or when the crank and cam sensor don't\015\012agree on position of ... 2000 Chevrolet Astro

I have a 1998 Chevy blazer I replaced the distributor and now it is running rough before I replaced the distributor it ran fine the only reason I replaced the distributor was a screw was broke so the cap wouldn't hold tight. I have tried to replace the cap and rotor but nothing helps.


I suggest check the right order, according with this diagram for 1998 Chevrolet Blazer 4.3 liter V-6 VIN "W"...Are you ... 1998 Chevrolet Blazer

My 1984 bmw 528e won't start sometimes? Come back later and it starts. plugs, wires, distributor cap, and rotor are good. coil ohms are correct. all plugs have a spark. It has been doing this since i bought it. my fuel pressure regulator was leaking so i replaced that. has anyone had this problem. last night i tried to start it and no go. went back 30 min later and started right up, i then cycled on/off 6 times with no problems? any help


SOUND LIKE WEAK FUEL PRESSURE.REPLACE FUEL FILTER AND CHECK FUEL PRESSURE IT SHOULD BE 33 - 38 PSI. IF FLUID PRESSURE OKAY.YOU COULD HAVE STOPPED UP DIRTY FUEL INJECTORS. ... BMW 528

1988 jaguar xjs v12. driving one day on freeway, loss power, would not restart. found dist cap and rotor shattered. replaced rotor and cap. noticed the distributor wobbles. replaced with another unit still wobbles. is there a certain way to install this distributor (lucas) or something else might cause this problem. is this a common problem on this type of car. please advise


Welcome to Fixya\015\012\015\012If this is the distributor cap that you purchased then all you need to ... Jaguar XJS

How do i replace the distributor cap and rotor on a 1987 bmw l7


... BMW Cars & Trucks

1995 Chevrolet K1500 Z71 350 4x4. I have a check engine code 43 and have replaced: fuel filter, fuel pump and screen inside the tank, egr valve, plugs, wires, distributor cap+rotor, pick up coil that's on the distributor shaft, the esc module that's under the distributor cap, and still have code 43. there is but 3 things left to replace that i haven't yet. the coil, the MAF, and another electronic module next to the MAF module. I got the feeling that I could replace the whole engine and sti


As much money as you have spent, you could have fixed it and had a lot of beer money left. First thing to check is the KNOCK SENSOR. should be located near the starter. ... 1995 Chevrolet K1500

I have a 96 Nissan 200SXE 1.6 liter eng. I recently replaced my distributor cap. I coiled spring fell out of the bottom of the distributor from a hole that holds a leg on the inside of the distr. cap with a metal contact. I lost the spring. The car is running okay without it, but it's not top notch as I would expect with a full tune-up, that included a new distr. cap, new rotor button, new NGK plugs, new premium plug wire set. What is the name of the spring and will I have to get a replace


You are not going to find individual parts for that distributor. The dealer is not going to have them either. The distributor is serviced only as a complete assembly, less the cap and rotor. You can try a salvage yard for a used distributor and pu ... Nissan 200SX

I have a 1998 GMC 1500 4WD pickup where I was just going to replace the distributor cap, rotor, spark plugs, and wires but notice that the distributor cap base (the shaft that goes down into the oil pump) one of the ''ears'' that are threaded for the distributor cap was broke and I had to fix that. So I then had to remove the distributor from the intake manifold. When I put it all back together the truck runs but ''spits and sputters'' when under load (in drive or reverse) but is driveable. Unde


I'm leaning toward timing 180 out too, but the easy way is to switch around plug wires on to of the cap. It's a faster way to determine if it it's the problem. Switch # 1 with 6, 7 with 4, 3 with 2 and 5 with 8. That will change where the spark goe ... 1998 GMC Sierra

Wont Start 1988 Mazda B2200 wont start after replacing,plugs, wires,rotor,cap and coil. What happenned? Cant figure what possibly could have gone wrong. Have done my own tune-ups before with no problem. Just finished putting plugs and wires on my 97Buick Regal. Pulled my Mazda truck in the garage today and replaced the plugs ,wires, coil, rotor,distributor cap and coil. The ignition system doesn't have points and condenser. My repair manual says its electronic. Have had this truck for about


Have another look at your plug wires, and make sure that you have them in the right order. As you probably know, if the firing order is wrong, you can have problems. That is somewhere for you to start, anyway. ... 1988 Mazda B2200

Wont Start 1988 Mazda B2200 wont start after replacing,plugs, wires,rotor,cap and coil. What happenned? Cant figure what possibly could have gone wrong. Have done my own tune-ups before with no problem. Just finished putting plugs and wires on my 97Buick Regal. Pulled my Mazda truck in the garage today and replaced the plugs ,wires, coil, rotor,distributor cap and coil. The ignition system doesn't have points and condenser. My repair manual says its electronic. Have had this tru


Sounds to me that you might have damaged the cap(dist cover) when you removed the coil btw you don't need to remove the coils on these trucks they last forever, so replace the dist cap with one from a junk yard with a coil in it and I bet you will ru ... 1988 Mazda B2200

I replaced the distributor cap and rotor cap,and plug wires.Now my truck will not start.When I turn it over,it turns very hard,and backfires.Could the timing have gotten off when I changed the distributor and rotor?


No. Not unless you loosened the distributor at the base of it. I bet that you got the plug wires on wrong. Crank the motor over to where the timing mark is on Top Dead Center. If you don't know what I am talking about comment back and I will further ... Chevrolet Silverado 1500

The motor is turning over but not firing up. I removed a spark plug wire to see if it was getting spark, nothing. I then replaced the wire n removed the wire running to the coil, then i got sparks. I removed the spark plugs n noticed they were full of gas (drenched). I let them dry, but think im going to replace them. I then removed the distributor cap. rotor looks worn n burned but my question is... If im getting sparks at the distributor cap why isnt it sending it to the spark plugs? co


Replace rotor button ... Chevrolet Astro

My truck idles up and down i have replaced everything on it all sencors etc. I have checked for vacum leaks and have replaced all of the lines replaced the gasket under the tbi the only thing i havent replaced is the pick up coil in the distributor. Fuel pressure is 10lbs i need help its driving me crazy i have replaced the o2 sencor new wires plugs and distributor cap and rotor what could it be replaced egr iac tps and everything


Hi i see you have changed allot of sensors, but i notice you have not mentioned the Idle Control Valve? iCV have you changed this? as that what it sounds like it will be, also have you checked your timing? that would also do it....hope this helps ... 1988 Chevrolet C/K 3500

I bought a 2000 civic with 67000 miles on it and it ran ok and was getting 38mpg notknowing about the car i bought plugs wires and distributor cap ingition rotor it had autolite plugs in it so someone had put plugs in it anyway i bought the good stuff 115.00 worth for 4 cyl and replaced all cap and rotor showed signs of being oringinal anyway i LOST 4mpg and it won't come back any ideas, i did put old plugs and wires back on made no diff .MY question is can a cap and rotor make 4 mpg diff or sho


The only thought that comes to mind is to re-check your spark plug gap, the reason is that if the gap is slightly larger, plug efficiency will drop, thus fuel economy and power, please confirm that some platinum plugs the gap is not adjustable, (.044 ... 2000 Honda Civic

The vehicle has fire out of the coil to the cap but nothing out of the cap to the wires. I have fuel. Replaced the timing belt and the timing marks are all on according to the manual. Car turns over with no problem will not fire. Car was being driven as it quit. Replaced cap and rotor also. Have not replaced pick up coil in the distributor. I was told that you can unplug the pick up and it should still run.


Hi\015\012Defective ignition wires will block the necessary voltage, which results in a cylinder misfire or no-fire condition. Several tests allow the vehicle owner to pinpoint the location and causes of faulty ignition w ... 2001 Volkswagen Cabrio

I'm having a problem with my wife's honda leaking oil from the distributor cap gasket. I took the dist cap off and the gasket was broken, badly, causing an oil leak. I've asked 2 others who wouldn't respond when I replied, so I'm asking you because you've helped me before. Am I ok to just replace the CAP gasket w/o having to take the whole distributor off or do I just need to take go ahead and mark the rotor for timing and dig deeper? Also, could the CAP gasket leak cause engine stuttering? Th


Hi, well first of all this is a very unusual thing to happen, leaking oil from a distributor, that sounds like it is a bad thing, normally you should not get any oil not one drop in there it should be dry and clean, this will ... Honda Accord

I have a 1994 Chevy Silverado, 5.0, and cannot figure out why the rotory cap keeps burning out? I replaced the distributor cap and rotor cap twice and still it burns out after a few days. I sand the black off the rotor cap and it will fire up. Why does it keep burning out?


... Chevrolet Silverado 1500

1996 Chevy S10 4.3 problem. Started surging at highway speeds and had code po300. Searched forums and found distributor has issues. Replaced distributor, module, cap, rotor and it seemed ok for a day.


... Cars & Trucks

My 1990 chevy pickup truck did not pass epa emissions test. I put in new plugs and wires, new distributor cap and rotor, and changed the oil. It ran alot better but still a little viberation, so I replace the ign. coil. Then there was no spark from the coil to the distributor cap, so thinking that the new coil was bad, i exchanged it for another. Still no spark coming from the coil to the distibutor cap. I checked the fuses and the wires for breaks, all that is ok. I am puzzled now. Can


Have you tried reversing the wire's on the coil ? ... 1990 Chevrolet K1500

I have a 1991 Honda accord lx. I recently had to change the distributor because it was leaking oil in the cap. I was able to get a distributor off a 1998 Honda civic ex. The 91 wiring harness was 2 plugs and the 98 was 1 plug. I was able to splice the 91 harness on the 98 distributor. I was told by a mechanic that would be ok but now I have a miss especially when the car is cold. After it warms up the miss almost completely goes away but it is still there. I also replaced the cap and rotor. Wha


... 1991 Honda Accord

My 1995 toyota tacoma is sputtering and backfiring going down the road but will idle fine the previous owner replaced the distributor cap and rotor spark plugs and wires and i replaced fuel pump and filter . recently i founf the condensor wire melted into in the distributor i replaced it and still not fixed what would u recomend


Check the ignition timing with a timing light. If that is good, check the pickup coil in the distributor and the ignition coil. I think the ignition coil can be replaced if it is faulty. But if the pickup coil is bad, the entire distributor may hav ... Toyota Tacoma

Weak spark at plug end. 1984 300zx was sitting for 7 years when I decided to put it back together. I emptied the fuel replaced the pump and filter and replaced plugs and air filter. Should be a go but failed to start. I troubleshot it by checking for sparks from the ignitors and #1 cylinder had a faint spark but other 5 nothing. I checked the spark from the coil to distributor cap and its very strong. Somehow it weakens as it goes through the distributor. Can I replace the rotor or is it


... 1984 Nissan 300ZX

Distributor on 97 Nissan Quest makes noise above 2000 rpm. Removed cap and everything looks ok. No play in dist shaft. Engine runs fine despite the noise. Car has 107K miles. Noise sounds like parts rattling about . If I need to replace the distributor is it still held in with a locking bolt? Do I just take note of the position of the rotor when taking it out and then put the rotor in the same position with the new distributor? Thanks in advance Phil Vourtsis


Ok can hardly make a noise that the dealer can be\012 is what you have run a little and listen to the dealer to hit a spark, \012if you get the dealer must mark the position in which you pull it out \012and put the new one in the same pos ... 1997 Nissan Quest

Engine misfiring. I have a 1996 GMC Suburban with a 454 ci engine and 235,000 miles. The misfiring started a month ago, I have replaced the plugs (ACDelco Set at 0.035), the Spark Plug Wires (2yrs old/15,000 miles on them) look to be in goog shape My next move is to replace the rotor and cap. Question: Am I correct on the gap for the plugs? What is the firing Order? Where is number one on the distributor cap? Should I replace the wires again?


... 1996 GMC Suburban
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.7350 seconds