Having problems with your Cars & Trucks ?

Witch terminal needs power to read obd2 codes on 2002 dodge ram 4x4

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Witch terminal needs power to read obd2 codes on 2002 dodge ram 4x4


... Cars & Trucks

How to power up obd11 connector under dash of 02 dodge ram 4x4 5.9 litre witch pin terminal can I power up so can get code info as scanner says no power to scanner so need to know what pin I can supply power too


Power pin for OBD II is pin 16. Just supply it with unswitched 12v and you are done. ... Cars & Trucks

I asked the question..."I have a 2003 dodge ram 1500 4x4 with the 4.7L engine. The check eng light is on. obd2 reads code P 0038 And says HO2S Heater Control Circuit High (Bank 1, Sensor 2). the heater is not working. How do I fix this?"... I apreciate the answer. But Does this have to do with the heater in the truck not geting hot? As in no hot air, only cold blows in cab. Its a 2003


P0038=HO2S Heater Control Circuit High Bank 1 Sensor 2,The oxygen sensors on your truck have an extra wire to them,they are a heated oxygen sensor,the computer sees a problem with the heated oxygen sensor on the drivers side,before conver ... 2008 Dodge Ram Pickup 1500

I asked the question...''I have a 2003 dodge ram 1500 4x4 with the 4.7L engine. The check eng light is on. obd2 reads code P 0038 And says HO2S Heater Control Circuit High (Bank 1, Sensor 2). the heater is not working. How do I fix this?''... I apreciate the answer. But Does this have to do with the heater in the truck not geting hot? As in no hot air, only cold blows in cab.


U need a vacuum chec-thats a common thing and it doesnt show on a scan-may also hav to inspec sensor--go to a parts place n get a repair manual-it explains how to perform chec ... Dodge Ram Pickup 1500

I have a 2003 dodge ram 1500 4x4 with the 4.7L engine. The check eng light is on. obd2 reads code P 0038 And says HO2S Heater Control Circuit High (Bank 1, Sensor 2). the heater is not working. How do I fix this?


Does fan run? just getting cold air? cut heater hoses near firewall, install a female garden hose bib on return and supply to heater core, first flush water thru return and then reverse direction a few times, my discharge air went from 65 to 140 ... 2008 Dodge Ram Pickup 1500

I'm having a issue with our 1998 dodge ram 1500 4x4 V6, it started when I disconnected the battery to put it in a jeep, I reconnected the same battery back into the dodge to find the alarm lights flashing with no sound and now the pickup won't start or even turn over.. is there a security code or feature I wasn't informed with? I read and read and read the owners Manuel to find out how to fix it, but it ain't got anything for replacing the battery and putting in a code afterward? Solution? Help!


Reset switch locater on pos cable link in black box located on firewall drivers side. most people remove these sometimes. sometimes they can be located in fuse box. if you have alarm remote try reseting it by removeing batter in remote then reinstall ... 1998 Dodge Ram 1500 4WD

I have a 2000 ford f250 super duty with the 6.8l v10, and its 4x4. my service engine light abs light came on and my overdrive off light started flashing while repeatedly chiming in and out every 2-3 minutes. I have a hypertech power programer and read the codes but all it came up with were 2 codes, p1000 which is an invalid code because it means obd2 has not finished analysys. and a p7a00. I can't find this code anywhere,and actually i found a forom stating it doesn't exsist or its a programer c


Try not using the programmer, and see if the issue\015\012resolves itself. Proccess of Elimination. Good luck. ... 2000 Ford F250 Super Duty Crew Cabs

I need a wiring diagram for a 1983 Dodge power ram 150 4x4. Can anyone help? Motor would crank and run only when the starter is engaged as soon as the key is switched back to the run position from start it looses power and cuts off. Some butcher has been under the dash and hood cutting and splicing, so I figure the best thing is to trace the wires and from one end to the other and fix the butcher's damage. Can anyone help or tell me where I can get a free diagram to solve this problem ? Thank yo


Its your balist resistor you will find it on the firewall,its useally made of white porcelin and has a 2 wire feed ... 1983 Dodge Pickup

TPS testing and adjustment 2004 Dodge Ram Hemi 4x4. Do you need to make an adjustment at sea level I bought the truck in colorado and live in cabo. And I replaced the TPS. Because it stoped running that's what code came. Still will not run. Getting same code


... 2004 Dodge Ram 1500

94 dodge ram 1500 4x4 having problems on cold start, runs rich and popping noise when underload and no power going uphill. Replaced throttle body, EGR valve, spark plugs and wires, distributor and rotor. Check engine light isn't on but when running codes get 12, 37, 55.


... Dodge Ram

Where is the ASD relay located on a 1990 Dodge Power Ram W250 4X4 with 5.2L V8? My truck shut off momentarily, but I was able to restart it right away. Has be running fine ever since. Code was "open circuit to Auto Shutdown Relay. Should I just replace the relay, or is there a more important problem I should address? Thanks, George


Replace the relay, it is an inexpensive part and is located in the power distribution box under the hood with a removable cover. ... 1990 Dodge Ram

What does obd2 engine code p1692 mean on 1998 Dodge Ram 1500 4x4


... 1998 Dodge Ram 1500 4WD

Dodge ram 1500 4.7 has no power to get reading off computer but the battery is good. The mechanic said I may need a new comuter brain.The truck started twice and within 2 seconds died then when I turned the noithing at all happened. Help! Mike Phoenix Arizona


... 2006 Dodge Ram 2500

Im getting a po303 code and I already replaced ign wires coil and checked plug 1998 dodge ram 1500 4x4 5.9 it starts jerking and it has plenty of power


... 1998 Dodge Ram 1500 4WD

Need color code for terminals on headlight switch 1997 dodge ram 1500 5.9


... Cars & Trucks

2004 Dodge Ram 1500 5.7 Hemi. EGR valve replaced, Did a #23 Fuse pull PCM reset. Engine slow to respond slight misfire. OBD2 reading at idle 620 rpm, MAP at 10.93 inHg, time at #1 is 11 deg and ATP is 14.12%. Is a fuse pull PCM ok or should I do a Battery Terminal pull reset? Also is 620 rpm a little low? And a MAP of 10.93 inHg a little high? Thanks, Rob


... 2004 Dodge Ram 1500

I have a 2001 dodge ram 1500 4x4 with a 360 motor. the rpms surge up and down when driving steady speeds(usually between 35-50mph). I had to tranny shop and they replaced the tcc/od solenoid 2 times cause it kept showing up on computer as code p1740. Need help figuring out. 600 dollars later the truck still drives the same


Since you have already replaced the TCC solenoid, this problem is then confined to one of the following, the wiring harness has a problem that gives a poor connection and set the code or the torque converter magnetic clutch ... Dodge Ram Pickup 1500

Battery died in a 85 Dodge power ram 4x4, got a new battery, now none of the lights work. Checked fuses, bulbs. Thinking it might be a short some where. Need diagram to trace wires.


YOU have either left a wire off the battery lug or a wire of the earth lug as the Red wires goes to starter motor and alternator,and elect like fues box etc and the BLACK wires goes to earth on the Engine bolt and on the body under the bonnet as the ... Dodge Ram 1500

I need a fuse diagram for the power distribution center for a 2001 dodge ram 1500 4x4 including relay switches I am not sure what relays are suppose to be in it.


... 2001 Dodge Ram 1500 Truck 2WD

I have a 2005 dodge ram 1500 4x4 4.7 liter with 81,000 miles my check engine light came on and i get codes P0404 and P0405 what component do i need to replace to fix the problem ? also it seems to be a little sluggish on acceleration until fully warmed up( 4 to 5 miles of driving)


Both of these codes point toward the EGR Valve being the problem. Purchase a can of carbon cleaner at any auto parts store. Remove the EGR Valve and clean all the carbon off. Look for holes in the valve that should not be there. If you see any ... Dodge Ram 1500

I have a 2005 dodge ram 1500 4x4 4.7 liter with 81,000 miles my check engine light came on and i get codes P0404 and P0405 what component do i need to replace to fix the problem ? also it seems to be a little sluggish on acceleration until fully warmed up( 4 to 5 miles of driving)


Do check to make sure the plenum of egr is not leaking, and do check to see if this is under warrant or recall. If egr valve is good, check the circuit for 25-30 ohms. If ohm is very low or too high, it may be a wiring or ECM Problem. If ohms are goo ... Dodge Ram 1500

2001 Dodge Ram 1500 4x4 engine light on and code reads P0455 could U please tell me what that means? thanks


Code po455 is a evaporative emission system leak.For example a loose gas cap.If your gas cap is good and tight and not loose.Check the gasket and make sure it is not deformed or torn.You need special tools for diagnosing the evap. system and a scan t ... 2001 Dodge Ram 1500 Truck 2WD

Need color code of speaker wire harns for 1995 Dodge Ram 1500 4x4


... Dodge Ram 3500

2003 dodge ram 1500 hemi 4x4, no power or throttle response!


I also have an '03 Ram 1500 with the Hemi, and I too noticed that the throttle system definitely sucks. The issue lies with Chrysler opting for speed density instead of mass air flow, which is what the Hemi should have. I landed an a chatroom that h ... 2004 Dodge Ram 1500

Need 2000 dodge ram engine code p 0505 code - 2000 Dodge Ram 3500


P0505------ idle control system\015\012 Have the idle air control valve checked, if that is ok, then further testing needs to be done to find the problem. ... 2000 Dodge Ram 3500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.5331 seconds