Having problems with your Cars & Trucks ?

1974 harley davidson shovelhead throwout bearing

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1974 harley davidson shovelhead throwout bearing


... Cars & Trucks

I have a 2002 ford mustang gt.. Replaced the clutch bout 3 months ago.. New flywheel throwout bearing.. The whole works. Even purchased a clutch adjuster kit with firewall adjuster.. Car rides good and shifts good just a few minor problems or questions rather.. If i tighten the clutch i get a squeeking noise from the throwout bearing? why? and also when i turn the air conditioner on the throwout bearing rattles? is this ordinary or whats the deal? the car drives fine and everything is brand new


... Cars & Trucks

Hi, i have an 04 Mitsubishi lancer oz rally edition, when i purchased my car my throwout bearing was bad but i continued to drive my car. after a few months it got to the point where my clutch went. i knew this would happen if i did not replace the bearing. i purchased a FX100 stage one clutch for my car and replaced the clutch, pressure plate, and throwout bearing. after this was fixed my car was making a very strange winding sound starting off, i thought it might have just been the newness we


... Mitsubishi Lancer

2002 Mazda has a bad throwout bearing, and will not start. I replaced clutch and throwout bearing a year ago already


... 2002 Mazda Protege

There is a rattling noise in my engine compartment that increases with RPMs. It only goes away completely when I have the clutch fully pressed down and I'm at a complete stop. Therefore I thought it was a clutch-related problem. I had my mechanic take a look at it, and he told me that the throwout bearing was bad. So, by his advice, I had him replace the clutch and throwout bearing, but that doesn't seem to have been what was causing the rattling noise, as it is still happening. Is it a just a l


Sounds like a transmission noise... have you checked the trans fluid?\015\012try doing a flush and replace it with a product called Syncromesh FM from the gm dealership. what motor? stock? it did wonders for my 95 civic ex ... 1995 Honda Civic

Wiring diagram 1979 harley davidson fxs - Harley Davidson Cars & Trucks


... Harley Davidson Cars & Trucks

Troubleshooting 2004 Ford Mustang 3.9 L, transmission. Vehicle whent into garage to have a new clutch pressure plate throwout bearing replaced. Pick car up at garage and the car developed a new loud clicking sound, whenever you were in neutral and let the clutch out, push the clutch in the sound would go away. Took the car back to have this problem fixed, and they diagnosed that it was the new throwout bearing and and they had also found that the input shaft was loose and wobbling also, so it al


... Cars & Trucks

2009 harley davidson sportster 1200 recalls - Harley Davidson Cars & Trucks


Hi Anonymous, call, take a ride or trailer your bike over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary/possible and offer professional advice and assistance con ... Harley Davidson Cars & Trucks

I heard a rattling noise in my truck when i was driving it. This noise occured in every gear except 4th. My truck is also a manual. So we tore the transmission off thinking it was the throwout bearing but once we got everything off the throwout bearing was fine so we did some more investigating...there is a gear that was in my transmission that is missing teeth. 8 teeth to be exact i'm not sure if i will have to replace my transmission or not what do you think? Where do i go from here?


... 1999 Chevrolet Silverado 1500

Throwout bearing i cant find anywhere on how to put a throwout bearing in and am looking for how to put it in... some places say one thing and others say something else and i am just looking for the simple answer on how to put it in please help me


This procedure is covered in a Haynes manual or a Chilton's Manual for your car. The throwout bearing is located between the engine and transmission, you have to remove, usually the transmission, to replace it. if you do not have one of these manuals ... 1990 Geo Prizm

Replaced a throwout bearing in a 1995 Eagle Talon esi and its still making the same noise. I checked the old Bearing and it was definitely bad. There was no clip or spring for the bearing and im wondering if there is suppose to be one. When I took the old one out there was no spring or clip in it either. To me it seems like there should be some type of clip or spring but every illustration I see don't show any. What could be causing this noise. When I start the car it makes a noise and if i enga


... Eagle Talon

Replaced clutch and throwout bearing now will not go into gear


These can be a pain to bleed is it is the slave is new. Keep bleeding it, try a vacuum leeder or try reverse bleeding with a hand oil pump. ... 1989 Ford F 150

Clutch issue after throwout bearing instal


Once you have bled out all the air ,if the pedal still engages right down then suspect the fingers on the release plate are worn.Never replace a part of the clutch, allways change all 3 components,it save all the hastle of taking it to bits again and ... 2003 Nissan 350Z

1990 geo tracker has a clutch problem.clutch got real hard to push and had trouble disingageing.i replaced the cable it was streached it worked for a while.it would have lots of free travel but just wouldnt move the clutch arm maybe a 1/4 of inch.so i replaced the clutch assy and still have the problem.i took the trans back out and looked at the throwout bearing arm and sleave that the bearing slides on it is worn and binding is this a common problem.thanks


Not necessarily, but if they weren't adjusted regularly, and the clutch gets sloppy, it works harder to apply the clutch lever. After a while it will pull heavily on one side, (usually opposite side of cable) and instead of pulling the l ... 1990 Geo Tracker

Starlet 98, final assembly of left hand side cv joint, original replaced with ADA drive shaft, cirtified by IS09002/QS9000/VDA 6.1. bearing locking wheel nut needs to pull up another 2/3ml to allow locking cap and pin to fit. can see from the back it needs to go that little extra. wheel spins freely, bearings seated with 0 wheel wobble or clearence, any, have you heard anything simular or have an explanation to my situation, something is preventing it from drawing up the full distance. regards


... 1984 Toyota Starlet

I need help replacing a clutch, pressure plate, and throwout bearing or clutch release bearing on a 2004 hyundai santa fe 2.4 l


It is a fairly easy job for any person to tackle providing they can handle tools, (some people can't turn a screwdriver), First you have to get the car up in the air with room to move under there, put it on jack stands if you can, but definitely on ... 2004 Hyundai Santa Fe

98 frontier 2wd making intermittent noise similar to the sound that is made when your tire rides over the safety grooves on the freeway. the sound seems to resonate through the body on the passenger side of the truck. Its not in the engine-its only while riding - ujoints are tight--carrier bearing appears ok--stepped on the clutch when the sound happens to see if it might be the throwout bearing and its not that---will appear at any speed


... Nissan Frontier

Throwout bearing The car makes high pitched noises and the steering wheel shakes at high speeds. Both front wheel bearings have been replaced.


... 2006 Mitsubishi Endeavor

I have a 1992 jeep cherokee the steering wheel qnd the front tires wobble i hqve q 4inch lift and 35x12.50 tires i put new ball joints and wheel bearings in and aligned the front end to 0 to 0


Have you checked your steering dampener? If not, unbolt one side of it and push on it like a shock. If it's easy to push all the way in, it's bad. ... Cars & Trucks

We have an '01 Mazda Tribute, 132,00 mi., 4cyl. manual, 2wd. we recently replaced the clutch, pressure plate, throwout bearing, pilot bearing and the slave cyl. because the clutch was slipping after the engine warmed up. Now a week after the repairs the clutch has started slipping again. I am stumped. I can't figure out why the new assy is slipping. There were no leaks that effected the clutch we removed. It was actually in fair shape. we resurfaced the flywheel. Any help would be appreciated.


When it starts to slip again open up the bleeder screw on the clutch slave cylinder. If the slipping stops then the problem is with the clutch master cylinder. The fluid is not able to return to the reservoir as it expands with heat and is keeping pr ... Mazda Tribute

I need instructions on replacing the clutch in a '94 Chevy Blazer 4x4, 350 engine. Specifically the pilot bearing, throwout bearing.


The poilt bearing just goes into flywheel center, you can remove the flywheel and tap it out from the rear. then install flywheel and tap new one in, remove the trany driveshaft, disconnect the battery terminal, drain oil from transfer case and trany ... Chevrolet Blazer

I have a 1990 jeep wrangler, the throwout bearing in the clutch has gone out for the second time. Is there a way of using the linkage from a new model to eliminate the doughnut hydraulic throwout?


Try using a bearing that is in a metal casiing and not a plastic piece of junk that comes in the clutch kit nowdays ,they always end up going wrong where bearing melts the holder ,unless you can fit a thin telecamit tube and a grease nipple so clutch ... 1990 Jeep Wrangler

RATTLING BEARING SEEMS TO BE FROM TRANSFER-CASE 97 F150 HAVE CHANGED CLUTCH THROWOUT BEARING STILL MAKES NOISE MORE UNDER LOAD SUCH AS TOWING


... 2004 Ford F150

I have replaced my clutch pressure plate throwout bearring pilot bearing. I still have a grinding noise when i let off the clutch in neutral. could it be that my transmission is bad or could it just need fluid


... 1995 Chevrolet C1500

I have 2005 Scion CT, with 5 speed manual transmission. The car has 75,000 miles on it. The problem I started encountering nearly two months ago is that when shifung into 5th gear overdrive, the transmission grinds. I have changed out transmission fluid to Redline Oil 75W90 when I had approximately 50,000 miles on it. So far I have not replaced any of clutch assembly or associated parts. Such as throwout bearing and pilot bearing. My clutch does not slip and my free travel/play is still within t


I had the same problem.. About a year of that problem i lost 5th gear and i had to replace my transmission. ... 2005 Scion tC
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3030 seconds