Having problems with your Cars & Trucks ?

Evinrude ficht ram 225 engine

\015 Excessive oil build up at the trottle body. Reed valvs are good.\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Evinrude ficht ram 225 engine


... Cars & Trucks

My 1999 dodge ram 1500 4 wheel drive 5.9 litre engine is showing that when i come to a stop the oil pressure gauge goes to 0 when i step on the gas moves to 40 psi. im thinking sending unit but may be wrong engine does not heat up or sound any different could it be a faulty gauge


Change sending unit first if aint that which is should be....it will need a new oil pump ... 1999 Dodge Ram

Engine light came on in 0 degree weather - 2006 Dodge Ram


... 2006 Dodge Ram

2004 ram 3500 4wd 5.9l DIESEL. Speedometer jumped between 10 and 50 mph several times then went to 0. Tach and engine hour meter ok . Everything else seems to be working fine


Change the sender unit on the differential ... 2004 Dodge Ram 3500 Truck

Are the oil sending units easy to change in a 2004 Dodge Ram 1500 4X4 Quad Cab 4.7 motor? oil sendig unit/possibly malfuntioning drops to 0 pressure at stop light when engine idleing at running temp, happened twice today for the first time since owning the truck for 4 years. Just had oil changed today hasnt dropped pressure yet, but I'm still wondering about the oil pressure sending unit?


They are real easy,here's a link on how to replace.Here's the ... 2004 Dodge Ram 1500

03 gmc envoy with 5.3 140000 miles. Oil pressure reading fluxuates between 0 and 40. When problem first started pressure read 80. When vehicle was new it stayed at midpoint (40) vehicle has plenty of oil. if you rev engine or increase rpms it goes to 0 and stayes there. let off and it jumps around like it did when started (0 to 40). No engine pecks while running. Display indicates low oil pressure and stop engine. orange light (check gages) comes on when at 0. any ideas. Service engine has not c


There may be a loose wire or the gauge or sending unit may be going bad. The first thing I would do is to hook up a temporary oil pressure gauge, not using the old one at all. With this watch gauge while driving and see what readings you get. If the ... 2003 GMC Envoy Xl

Ford Focus engine diagram Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V


... 2001 Ford Focus

Hyundai sonata 2000 gls. v6. HAs no EGR. Emission test, first try, HC(0) CO (0) nox 1033 mechanic said my engine seems hot (there was also heat out of vents blowing out. I cleaned my maf sensor and put on high octane gas and fuel cleaner drove for a week and retested. ssecond try HC(0) CO (0) nox 1250. failed agian. I changed my mass airflow from anotehr car and change my 3 front spark plugs myself not the three at back. Car seemed to be running better and engine definitely cooler no mor


... 2000 Hyundai Sonata

91 Corvette - Service Engine lights, Speedometer goes (usually) to 0, Average miles per gal goes to 5Y5, engine stops. Engine cranks but will not start. Wait a bit, remove key, insert key and it will usually start. only code is 12 which is normal. (Speedometer sometimes goes to 108 or 17 instead of 0 - while sitting and Idleing) Can sometimes get out of engine stopping by flooring it - must be driving to do this.


... 1991 Chevrolet Corvette

Ignition When I turn on the ignition I drive a few feet and when I stop the rpms goes down to 0 and the engine turns off, some times it turns on but the rpms go down to 0 without driving and the engine turns off. No check engine light is on.


Check your fuel filter and fuel pump. ... 2000 Mitsubishi Montero Sport

Propercrankpositionfor correctbelttiming is there a timing mark onthe crank pulley for refrence to line up with a notch on the engine ,besides the flyweel mark? i am puzzled because i have already bent some valves & dont want to repeat my mistake. i have put the #1 piston at TDC, flat with deck ''0'' deck is this right or should it be slightly below ''0'' deck hight and or should the key way be at 12:00 position. please help me P.S, this a 89 honda accord 2.0 carb.3V A20A1 engine


Send me your email address and I will send you the proper timing positions. I can copy them from mitchel and email it.... ... 1989 Honda Accord 4 Door

Is it possible to change the miles on a 1992 GMC Sierra (1500)? I just switched out the v6 with a new 305 and for personal preference I wouldn't mind setting the miles back to 0. Not selling the truck, I mean I could always write down it's current miles to know how many miles are on the engine but it would be nice to set to 0 since its a new engine.


No if you want one with 0 miles you will have to get a new one ... 1992 GMC Sierra

98 buick lesabre oil pressure dropped to 0 and engine died. added 1 quart oil, waited 30 minutes, started and drove 5 miles then oil pressure dropped to 0 and engine died. does this sound like a bad oil pump? where is the oil pump and is it hard to change for a "handy" person? thank you.


My sister had the same problem. There are 2 sensors that can cause this when they go bad. One is the oil pressure switch, which is located near the oil filter. When the PCM reads this switch, and gets a low reading, it will automatically kill the eng ... 1998 Buick LeSabre

I have a 2003 Dodge Ram 1500, with a 4.7 L engine, Does anyone know what all years and model engines will interchange? i have been told 03, and 04 Ram 1500 only, and then others have said that a 03 to 05 Durango, Dakota, or Grand cherokee will also interchange. Does anyone know for sure?


... 2004 Dodge Ram 1500

Overhaul of the top in of 2003 jeep 4.7. It had jumped time, broke a valve spring and bent a valve. After the overhaul oil pressure at idle drops to 0 after the engine warms up. No engine noise what so ever. pressure jumps up while driving, but at idle drops back to 0. Afraid to drive, what should I do?


First thing you need to do is put a mechanical gauge in place of oil sender and read actual oil pressure. If mechanical gauge shows same condition, take a look at the connecting rod bearing serving the cylinder where the valve bent. If the piston hit ... 2003 Jeep Grand Cherokee

1998 dodge ram 1500 oil pressure gage drops to 0 when warm. replaced sending unit to no avail


... 1998 Dodge Ram 1500 4WD

May have a vacuum line leaking, engine light comes and said it was gas cap, replaced that and it still comes on. how many vacuum hoses are on my ram? Dodge Ram 2001 club cab magnum engine.


Many vacuum lines, but if it indicated a bad cap it should just diagnose the fuel vapor system. Your unit is 8 years old. Check the filler tube to see if the hose clamps rusted off. Being a bearer of bad tidings it could also mean the tank is rust ... 2001 Dodge Ram Maxi

I have a 2001 Dodge Ram 1500 5.2L, 197000km/120000miles. The cat was plugged up with no engine power. It occasionally smoked upon ignition. It occasionally smoked out an oily soot from the exhaust. The cat was replaced with a new one. Idled roughly. Engine chugged at lower vehicle and engine speeds. Engine light came on solid. At 120km/hr, 70mph the engine light started flashing, also at high rpms low speed. Engine codes are P0300, P0303, P0306. Oil at air filter, replaced. Plugs were all change


The plenum problem should not affect compression tests. It allows oil to get sucked into the intake and will cause carbon buildup, plug fouling, and pinging. If you have zero compression on a cylinder, it is usually a valve problem. Even a burned pis ... 1999 Dodge Ram

Can anyone tell me what these engine fault codes refer to on a 1998 mercedes c180 auto,1.8 petrol. I suspect it may be releated to tempeture sensor. Total of 6 codes 065 (2,2,0,41) resistance too high 104 (2,2,0,68) resistance too low 122 (2,2,0,7a) resistance too low 126 (2,2,0,7e) resistance too low 129 (2,2,0,81) resistance too low thanks jim 161 (2,2,0,a1) resistance too high


Most common is o2 sensor ... 2002 Mercedes-Benz C-Class

RPM Oscillating I have a Dodge RAM 3500, year 2005, with Cummins Turbo Diesel Engine, 6 cylinder, 5.9L, 24V and automatic transmission. The problem is that when I accelerate the engine to 1800 rpm, the engine speed increase from 1800 to 2500 rpm and soon it begins to oscillate betwen 2300 and 2500 rpm. The engine doesn't present/display fault codes. Below 1800 rpm the engine is ok. If I disconnect the boost pressure sensor the fault it disappears and the engine runs correctly I replaced the TPS,


Have you had the vehicle speed control reprogrammed if not that could be your problem ... 2005 Dodge Ram 3500

I have been told that you can not put any engine in the 2004 Dodge Ram 1500, expect the stock engine. Is this true? The cost I was quoted to replace the engine was $5000.00, for a rebuilt engine to be put in. But I do not want the stock engine back because of the problems it has with the oil. any helpful post would be great.


You can replaced it with another enigne but stock. The 2005 Ram 1500 engine will fit right in. If you are trying to get a totally different manufacture engine then you will need to make sure that the mounting bolts, tranny and everything else lines u ... 2004 Dodge Ram 1500

1998 dodge ram pickup 318 eng. engine idle rough on warm-up engine idle rough after warm-up shutting off engine and starting back up engine also runs sluggish in over drive at a low idle. I have replaced , plug wires,coil,plugs,distributor cap,rotor,o2sensor, engine runs well over 1500 rpms.


If the engine seems to run fine over 1450 RPM maybe there is a vacuum hose leaking or EGR valve is slightly stuck open. Any help from the OBD II trouble codes? Or is there simply no MIL and no stored information in the OBD II computer read at the loc ... 1998 Dodge Ram 1500 4WD

Pliz help after taking my car for engine wash they used water to wash the engine and engine Codes came up . 16502 P0118 Engine coolant temperature circuit-G62:high . 16497 P0113 Intake air temperature sensor 1 circuit-G42:high. 16486 P0102 Mass air flow circuit -G7 0:low input. 16622 P0238 Turbo super charger boost sensor (A) circuit : high. 16955 P0571 Brake switch sporadic (A) circuit : malfunction. 18000 P1592 Altitude sensor /boost pressure sensor :implausible ratio. 16706 Engine RPM sens


Not Good: The Expensive main computer brain sustained a short from either the heat of the solutions or leakage allowing fluids to enter the components. If after a drying period this still occurs; then the computer brain needs replacing. ... 2005 Volkswagen Touran 1.6

06 dodge ram hemi engine knock at idle from bottom of engine


Sometimes a valve lifter will stick and cause a ticking it is possible that a valve lifter has lost its prime or it might be that the oil is too thin. Wthout more info my bet would be a lifter ... 2001 Dodge Ram 1500 Truck 2WD

My vehicle is a 2002 dodge ram 1500 with a 4.7 engine. I'm looking for a series of hoses (3) that connects from the coolant reservoir to two other hoses that stem from the engine. The hose stemming from the engine is the larger hose of the three that is connected by a plastic T connector which join the two smaller hoses that stem from the engine. I've contacted the dodge dealership and they mention that they dont make the part anymore and that the only way for me to get the part is via aft


You can use a three way tee that you can sometimes find with some of the nozzles a different size that you can get to work.or if you know someone that works with piping they may be able to make one up for you as long as you know the hose sizes. ... 2004 Dodge Ram 1500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.9666 seconds