Having problems with your Cars & Trucks ?

2002 jeep liberty 3.7l starts but dies when you let off the gas. They told me to replace the fuel pressure regulator when i went to buy it they said to change it if the pressure is too high mine is too low its at 30 psi check engine light is on we went to scan it it says to turn ignition switch on it was on now i'm confused please help

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2002 jeep liberty 3.7l starts but dies when you let off the gas. They told me to replace the fuel pressure regulator when i went to buy it they said to change it if the pressure is too high mine is too low its at 30 psi check engine light is on we went to scan it it says to turn ignition switch on it was on now i'm confused please help


... Cars & Trucks

2002 1.9 sohc mp efi missing badly on #1 cylinder. new plug .wires,fuel filter.compression good.check engine light been on for several months showing egr fault. cleaned no help.installed another no help,change injectors around still missing on #1..check fuel pressure at idle 48 psi clamped off return fuel line pressure went up to 55 psi miss went away.keep trying different things and found that when i disconnected the map sensor in the top of intake manifold it also made the miss go away but the


SOUND LIKE A BAD OR DIRTY FUEL INJECTOR. ... 2002 Saturn S-Series

I just had an oil change and my air filter changed out 3 days ago. Tires rotated and pressure checked 4 days ago and when they checked pressure during oil change said they said it was way too high and let out air. Don't know if they were right anyway after that. Filled up with gas last night and went to work this morning, everything fine. Go to go to lunch and my engine light came on, cruise light blinking (tried reset in case I did hit it. Didn't work), and my vehicle dynamics control "off" lig


... 2006 Subaru B9 Tribeca

Need toyota expert please.I completely rebuilt the engine on my 1998 toyota camry. I drove it for 11 months with no problem. then the oil light came on. The oil level was fine . I checked the oil pressure with a manuel oil pressure guage and got 5-8 psi. I checked the oil pump and relief valve . I replaced the oil pump and had the same problem.I took off the valve cover and I do have oil on the top end of the motor. When I started the car the oil went up on the windshield of the car. I blew air


That does not happen only on Toyota.If you already replaced oil pump, and newly installed pump is working, there is no oil leak and you already checked oil lines to exclude blockage, that can be due to a cracked or incorrectly installed head ga ... Toyota Camry

Had oil changed 3 days ago...oil pressure had been fine until today. I drove about 3 miles and pressure became erratic and pegged high and then pegged low. It did this several times and then went to zero and stayed there. I checked the oil level and it is fine and there is no sign of oil in the coolant and the engine is running fine. Any idea what the problem is?? Is it just a pressure sending device or could it be the oil pump itself?? Thanks!!


Your,e oil pressure switch is located close to your,e oil filter,it problemy disconnected the wires going to the switch.reconnect them. ... 2001 Pontiac Bonneville

Check engine light came on, then noticed the oil pressure was too high (80 psi). drove @ 8 miles - no noise from engine? Any suggestions as to what the problem is?


... 2006 GMC Envoy

Car dies out and gages dont seem to work when it finally startes got a check engine light and theft checked fule at injector rail got good pressure and fule pump works fine. Disconected batery for a half hour and hooked back up started back up idled high went arround the block a few times and it died out. stared up after sixed time but gages were not redgestering, also had service ligt and the theft ran but felt like it was been weighed down and when in park it would idle for a few minutes and t


Check for wire touching ground check sensors its normal for the car to run high when you disconnect it because you cleared the computers memory and it had to get new information as to how the car is running again it takes about 15 mins for it to rest ... 1998 Oldsmobile Intrigue

2000 F350 Super Duty V10 Power problem, Truck starts up ok, but has a problem on acceleration, I changed the fuel and air filter with no difference. I checked my fuel pressures and they seem low to me....With key on and engine off Ihave 13psi, engine started and idling I have 30 psi turn off engine and the pressure drops 2psi and then came up to 32psi with engine off and holds there at 32 psi. Also I want to make sure that i checked at the correct spot.....On the right side of engine (as seen fr


Your choises are...bad fuel pump, restricted fuel filter (new?) bad fuel pressure regulator...out of gas....can you pinch off the return fuel line to the tank? some are rubber and some are hard plastic...dont pinch the plastic. This will give you the ... 2000 Ford F350 Super Duty Super Cab

Start motor , no oil pressure showing on guage , check engine light on, when first noticsd checked oil ok, started motor 2-3 times no pressure on guage, 4 th time got good pressure reading light went out, drove 30 miles no problems, started up next day no pressure reading check engine on again, stays on and no presure raeding since thanks


I would find and replace the oil pressure sending unit although oil pressure is ok the computer needs to know or else it will shut down engine and it seems like your oil pres. sending unit is starting to stick. ... 2005 Chevrolet Silverado

1996 gmc jimmy wont start seems like advanced timing issue backfiring out throttlebody, replaced timing pick up, distribitor cap, crank sensor, ICM, when ignition conrol module replace the engine ran fine for about 4 seconds and went to backfiring out throttlebody, then replaced injectors inside intake manifold, still backfiring. it has 65 psi fuel pressure. this whole problem started after wife drove car it quit and had to tow home. distribitor is tight. i have not checked with a timing light.


You said the problem happened right after the engine was replaced correct? If so bring number cylinder to top dead center on the compression stroke. Remove the distributor cap and see if the rotor is lined up with the number one spark plug wire. It's ... 1996 GMC Jimmy

2001 discovery automatic td5. problem is engine cut out and would not restart checked cranksensor fuel pressure removed ecu and checked for oil leaking into same ok removed top cover checked injector wireing ok. plugged in launch x 431 no engine fault checked relays tried to restart after a while it started i noticed 2 green lights in dsah for auto box flashing after a few restarts lights went out. drove about 70 miles no problems. went to start 2 auto lights in dash were flashing gearbox in lim


It takes 3 amps to run your ecm, you need to check your power wire to the ecm and ground wire however I do expect you to find the power wire bad or corroded, and that will give you all your faults,I have had this problem before ... 2000 Land Rover Discovery

Oil pressure guage not working. check engine light not illuminated, engine not overheating,oil up high on dipstick with engine running. drove 5 miles after guage quit working! I suspect oil pressure guage or sending unit,however I do not know where sending unit is located on engine or how to trouble it. Is my diagnosis correct and how do I check? please help


Sending unit should be in this location. This is a cheap part that likes to fail. ... 2002 Ford Mustang

Went to advance auto parts store and had some codes pulled for my check engine light. Theses codes came up P0113 IAT Sensor 1 Circuit High Input, and P0103 MAF or VAF A Circuit High input. My car stalls when I come to a stop and when I start it up it stalls right away unless I rev the engine and then when I get it going again I can't get past 45 miles per hour and the rpm guage races up to 4. The next day I started it up and it started idling high for a minute or 2 then slowly went down and


Both fault codes are refer at air intake system; check this information to solve it...P0103 - Mass Air Flow (MAF) Circuit High InputBasically this means that there is a problem with the Mass Air Flow High (MAF) sensor o ... Hyundai Sonata

1987 Chevrolet S-10 Pickup1987 chevy s10 2.5l tbi will not start. changed bad fuel pump works well now strong pressure to throttle body. change fuel pressure switch, oil pressure switch, o2 sensor, map sensor, distrib cap, rotor, electric part on dustrib, check for 12v to fuel injector good, check ground good, fuses good, ecm swapped changed fuel injector engine runs now but runs high idle and will not wind down. when i step on gas engine bogs down


Check the trottle body postioning sensor... ... 1987 Chevrolet S-10 Pickup

99 grand cherokee 4.7 v-8 engine missfires at rpm's under 2000 ran compression check [good] coolant system check [good] obd only one code p0500 vehicle speed sensor changed plugs,checked spark at coils [good] plugs carbon up after or 15 minutes black inside throttle body drained fuel, added clean fuel , gas dryer, and injector cleaner suspect high pressure in fuel rail, but have'nt tested yet try to relieve fuel pressure by disabling fuel pump after disabling pump, engine runs much b


It is most likely the fuel pressure regulator,it will have a vacuum line going to it,make sure it is getting vacuum,and the hose going to it is in good shape.Ether the regulator is bad,or the return line going from the fuel rail,to the fuel tank is r ... 1999 Jeep Grand Cherokee

I have a 2000 Pontiac Firebird with 90,000 miles on it. I put in Gunk engine cleaner and ran it for 5 minutes as directed then drained the oil. I then did an oil change (Quaker State 10-30) and put in Lucas oil stabilzer (heavy duty). The oil pressure at idle is 90 psi and when driving it could go as high as 110 psi. I removed the oil pressure sensor and blew it out with compressed air and there was no change. If the sensor is faulty would it show high pressure? Do I have oil blockage or is the


The sensor can show high pressure when that is not the case, they fail high not low, take the sender out and plug in a mechanical guage to verify this, that is the only way to be 100% sure. ... Pontiac Firebird

2003 jeep grand cherokee 6cyl. Oil pressure drops as engine warms up.replaced sending unit, same. Checked with mechanic's pressure gauge and found out gauge on cluster is correct. Pressure drops below 5 when the engine is warm.Removed oil pan and found pickup screen was clogged by sludge.Replaced oil pump and screen, cleaned oil pan. Now pressure stays at 10 psi at idle when warm. However, it can not create pressure after start up, light stays on until you rev engine up and bring pressure close


The reason it differs from cold to hot is because your oil is thicker when cold, as the engine heats the oil thins a bit causing the drop. Good news is, you do not need but about 7psi at idle to keep the engine properly oiled. (to bring oil to the t ... 2002 Jeep Liberty

Hi my problem is with a 2000 buick regal 3.8 super charged engine code 1. when the ignition is first turned on the PCM energizes the fuel pump relay and pressure is 50 psi.,when engine starts fuel pressure drops off and engine stalls,after the engine stalls fuel pressure builds back up to 50psi.there was a truble code P0230.I have checked pins and connectors at PCM ane relay's for damaged or broken terminals.Continuity test on grn.wire at pin 39 blue connector of the PCM to the connector at the


Hello! Are you using a "digital" volt meter? if not you'll need one...Connect the + probe of a volt meter to the Dark Green/White wire and the - probe to ground...turn the key to start and see if the + 12 volts from the ECM to the relay winding stays ... Buick Regal

Compressor will not engage, 80 PSI on high and low side. Fuse under dash good, fuse under hood don't know how to check. Does high pressure switch break circuit on high pressure or break circuit on too low of pressure. Where is low pressure switch?


The switch shuts off compressor when its low on freon..try adding some ... 2001 Hyundai Santa Fe

86 SS Monte Carlo losses oil pressure at high rpm's, I've checked the gauge and its accurate and put a larger oil pan on it and and a pick-up tube that came with the pan and changed oil pumps and at wide open throttle the oil pressure goes from 70 psi to 25psi and as soon as you let off the throttle it goes back to 60 to 70 psi and the motor has a pretty fresh rebuilt with about 10,000 miles on it, any suggestions on what to check next?


I have to be honest, it sounds like a cheap oil filter. ... 1986 Chevrolet Monte Carlo

2005 chev express 1500 cargo. 4.3 liter V6 100k miles Problem: engine rev's stay high as it moves thru the AT gears (used to smooth out and not have the high rev sound) Feels a little more sluggish than prior to issue, just started 4-4-11. Background: 'check engine' light was on from 4-2 to 4-3 then went off. the only thing i did was check the gas cap and fill the tank. vehicle start/stop cycles since issue = about 4 and counting. thanks for any idea's you have.


... 2005 Chevrolet Express

I have a code PO102 when I ahd my engine checked. What is the usual problem that casues this. Is it the hose? the MAF? or the Mas absolute pressure sensor? Peg The check the engine light went on so we checked the engine and this was the code that came up P0102.


COULD BE A FEW THINGS, WIRING SHORT TO EARTH,MASS AIR FLOW SENSOR,VOLUME AIR FLOW SENSOR OR ENGINE CONTROL MODULE, BUT CHECK AIR INTAKE HOSE FOR LEAKS/ SPLITS FIRST ... 2002 Buick LeSabre

OK GUYS really need some help here!! 2004 mitsubushi endeavor has oil pressure idiot light no pressure gauge. problem: very noisey valve lifters and oil light on check engine light came on about two days ago, did oil change about two weeks ago about 87k on v6 otherwise engine runs great smooth, has all power but sounds like a diesel engine (it's a gas motor) engine ran fine after oil change and had no issues,one strange thing Iput quart of STP in and loose load lifter sound went away, then I dro


I'd find a garage mechanic that has a mechanical oil pressure gauge, or buy one and install it first to confirm what is really there for oil pressure, then go from there, once that is confirmed. ... 2004 Mitsubishi Endeavor

Fuel Problems I just purchased an 89 Ford F150 with a 302 and it will not start without ether or gas but once it starts it runs on its on and at idle is running rich (black smoke out of exhaust). I've replaced high pressure pump, fuel filter, pressure regulator, and cooling temp. sensor. With key on engine off it has 40 pounds fuel pressure. The check engine light stays on constantly and the fuel pump runs constantly and when I try to get self test codes the light never blinks..it just stays on.


Check for air inlet at carburettor leaks. ... 1989 Ford F 150

We changed the High pressure oil pump on a 2002 7.3L DIT engine for a F250 in Australia but we have been unable to start the engine since. We checked the oil pressure at the rail and got 50psi. The engine winds over but just will not fire. Any suggestions??????


... 2002 Ford F250 Super Duty SuperCab
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.1422 seconds