Having problems with your Cars & Trucks ?

Need timing marks on crankshaft and camshaft on 95 honda civic 1.5L engine

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need timing marks on crankshaft and camshaft on 95 honda civic 1.5L engine


... Cars & Trucks

I have a 1989 dodge colt with a 4g15 engine this is a 1.5 litre, i just repair the engine because the timing belt fails, but i need to know the timing marks to sinchronize the crankshaft with the camshaft, the cam pulley has a mark but i dont know the aligning mark that sinchronizes with the cam pulley i need a diagram or something please help me


... 1991 Dodge Colt

Need to verify the timing marks on my honda civic engine i've lined them up like it shows but the engine still turns over like it has no compression after timing the belt the cam gear has the 3 lines on it to line up the middle line with the pointer and the outside 2 line with the valve cover surface of the head. i suspect possible valve damage but was told this engine would not suffer that fate if the engine jumped timing?


This engine is an interference will bent valve's, if the timing belt broke you have bent valve's as far as how you set the camshaft gear you did it right, the cylinder head will have to be remove to repair and replace bent valve's. ... 1996 Honda Civic

I need to know how to set the timing marks on the camshaft and crankshaft on a 1995 toyota camry 5sfe engine, also if the camshaft pulley has to be removed


... 1995 Toyota Camry

I took off the timing chain and didn't line up the marks on the chain to keep the crankshaft and the camshafts in the right position to stay in time. I was installing a new oil pump on a 2001 Chrysler Sebring Sedan 2.7 engine. I have turn the crankshaft to TDC, but can I turn the camshaft sprockets to where the picture in my book shows what they should look like. The mark on the sproket at 90 degrees from the cylinder head and there are 12 chain pins between the timing marks. Or am I going to h


... Chrysler Sebring

Well,Im very leary in taking off the belt at this time because my camgears are not lining UP. I put it on TDC from crankshaft o #1 piston up and I installed the rotors so I could see if it was pointing to #1 cylinder and it wasnt the were both pointing to the camshaft timing marks on engine the rotor wasnt pointing to the #1 cylinder. Do you think that the rotor should point to the number #1 cylinder instead of the timing mark on the engine for the camshaft?


Set the crankshaft pulley mark to the "0"...make sure the marks on your camshaft pulley line up..click on this link and it shows you exactly how to do this with detailed pictures:\015\012\015\012 ... 1990 Lexus LS 400

Need the rite timing marks for a 1990 honda civic 1.5 engine


On the cam shaft gear there are two "-" marks on either side of the gear along with the word "Up" stamped on the gear. Turn the crankshaft so that the word "up" is on top and line the "-" marks up with the cylender head. On the pulley of the drive sh ... 1990 Honda Civic

I am in the middle of replacing the timing belt on a 05 honda odyssey touring, before removing the old belt, the manual is saying to turn the crankshaft pulley to its white mark [which i can see] lines up with the pointer [B] on the engine block [ which i can also see], the manual also says to set the No. 1 piston at top dead center TDC by aligning the pointer on the front cover with the No.1 piston on the front camshaft pulley, the problem is as of now with the old belt still in place, when i t


Remember that for every rotation of the cam there two rotations of the crank. Rotate the crank a further 360 and bring the piston to TDC and the white mark should now align on the cam. ... 2005 Honda Odyssey

1986 honda civic hatchback timingbelt replacement need to know the marks for the timing shaft and crankshaft ... top dead center doesnt help


The red mark is where the timing is supposed to be after u have bypassed the electronic advance.the first white line on the left is tdc. ... 1986 Honda Civic

I have a 1996 Honda Accord and I have replaced the timing belt...I need to know if anyone can help me with the camshaft and crankshaft markings.


There should be markings on the gears or pulleys for both parts. It would be a diamond or dot. The top part should be your cam and the mark would go on the bottom directly over the mark on the crank. The crank mark should be at high noon. They sh ... 1998 Honda Accord

I need to know the timing marks for a 2002 honda civic 1.7 litre engine


There are 4 marks on the crank pulley. When standing on the driver side of the car looking down on the pulley, the mark farthest to the right is the mark for TDC (Top Dead Center). The three marks on the left are for the spark timing. Of ... 2002 Honda Civic

Crankshaft and camshaft timing marks - 1990 Honda Civic


Hope this helps? ... 1990 Honda Civic

I need the timing marks to set the crankshaft to top dead center for a timing belt replacement. I just need a diagram to show me where the timing marks are located, where should the camshaft pulley mark be pointed to ?


1986 Dodge Truck RAM 50 4WD 2.6L 2BL 4cylFig. Timing belt and components-2.0L engineFig. Location ... 1986 Dodge Ram 50

I'm receiving conflicting information about the 2004 Honda Civic Hybrid w/the 1.3 L engine. I need to know whether this particular model's engine has a timing belt or chain. No one, including a local Honda dealer, seems to know for sure. This is very frustrating when a mechanic can't say for sure.... belt or chain. Anyone out there know for SURE, or do I need to post more info regarding the model or engine specs/numbers?


It has a chain. ... 2004 Honda Civic

Okay. I got the old timing belt out and found that all the teeth were gone where it goes around the crankshaft gear. I put a new timing belt on and lined up the marks, but when I rotate the engine several times the timing marks on the belt move over a few teeth off the camshaft gear marks and no longer line up. I'm using a Haynes manual for this, but am I missing something that they don't say in the book?


The marks on the belt itself will not line up with gear marks after rotating engine as long as engine marks line up you are fine however these are know to bend valves ... 1991 Nissan Pathfinder

I replace the oil pump gasket. need to redo timing of the engine cause it wont start, it has a distributor. which timing mark ( has about 6 marks)on the crankshaft pulley and does it align with the pointer that is attached on the block when the # 1 piston is at TDC.also whats the torque on the crankshaft bolt.


Didnt i answer this one ,but you never stated a distributor ,easy take no1 plug out ,bring up to to TDC no1 and rotor points at no1 plug point on the distributor cap.if it doesnt start then you could be 180? out which is why its better to remove rock ... 1998 Nissan Frontier

I replaced the head on my 1988 D-50, 2.6L engine. Now I cannot seem to get the camshaft and timing set up properly. I have the little hole aligning up with the top right side of head, and the crankshaft mark centered on the pulley mark. But it is coming up as top dead center on cylinder # 4. If I get the crankshaft to line up with the # 1 cylnder at top dead center, then the hole on the camshaft gear is aligned up with the left side of the head. I have a Chilton manual, which practically worthle


Is the following what you see? Fig. 10: Timing marks ? 2.0L and 2.6L engines ... 1988 Dodge Ram 50

1993 Geo Tracker 1.6L was running rough. Removed and replaced timing belt after found worn and had jumped one tooth. aligned crankshaft and camshaft with alignment marks,and rotor button to #1. Would not start. Removed again and i have now moved the crankshaft,camshaft and the rotor button separately. Now i am confused ! How do i get this engine back in time?


You will need to have a service manual. Basically what you need to do is make sure the number one cylinder is at top dead center on the compression stroke and the valves for the number one cylinder are both closed. You will need to have the tim ... 1993 Geo Tracker

1992 Volvo 960 Broken timing belt - need to locate alignment marks for crankshaft and camshaft and associated reference marks for TDC or other position. Car was cranked AFTER belt broke - Crankshaft Is therefore likely not aligned with camshaft pulley position.


IF U BROKE THIS BELT WHILE DRIVING U HAVE BENT THE VALVES IN THE ENGINE, THIS IS WHAT IS CALLED AN INTERFERENCE DESIGN ENGINE, THAT MEANS WHEN THE TIMING BELT BREAKS THE PISTONS HIT THE ENGINES VALVES ... 1992 Volvo 960

Hello i wanted to know the ignition timing advance specifications for my Honda Civic LX1.5 (philippines) with a D15B3 engine (carb). I wanted to know what is the specificition for the initial advance and the total advance (with vacuum hose disconnected). also i normally just use a timing light to check on the timing and with vacuum hose connected i set it where the timing marks (the three notches on the crank pulley) is centered on the timing mark pointer on the lower timing belt cover. These


... Cars & Trucks

I have a 1995 1/2 Isuzu Rodeo with a 3.2L V6 SOHC engine. It has 57,000 miles on it so I am changing the timing belt. The manual (Haynes) that I have says and shows the alignment of the timing marks on the sprockets, belt etc. It says that the grove on the crankshaft sprocket should align with the cast in mark on the left side, front of the oil pump. At the same time the camshaft sprockets should align with the dots on the timing belt back covers as well as the solid lines on the belt. I hav


Hi!!\015\012\015\012Click on the following link http://www.autozone.com/autozone/repairinfo/ ... 1995 Isuzu Rodeo

Chrysler Sebring 04 2.7 l. I need to have the diagram for the timing chain with the timing marks. I have replaced the water pump, but failed to check alignments. I aligned the crankshaft mark with the arrow mark accordingly, but the marks on the right and left camshafts,how does it have to be aligned?I see a dot on the right cam which is 25 degrees below a straight line towards the left and an arrow on the left one is also about 25 degrees below a straight line towards the left and the same is


Rotate the crankshaft until the Top Dead Center (TDC) mark on the oil pump housing aligns with the TDC mark on the crankshaft sprocket.\015\012\015\012\015\012\015\012Install an Allen wrench into the tensioner. Rotate t ... Chrysler Sebring

My timing belt broke on my 1996 Ranger. It's a 2.3 5 spd - Replaced the timing belt, aligned the crankshaft at TDC before teardown and also made tick mark to align it without having to replace timing cover. The camshaft and oil pump marks line up perfectly. I rotate the crank twice to verify that everything lines up (it does) then start the engine. It dogs when I step on it, telling me that the timing is off. When I line it TDC afterward, everything lines up. I checked the deflection on the belt


Is it possible that when the belt broke you may have damaged the engine (bent valve). Try advancing or retarding the camshaft sprocket by one tooth and see if that makes a difference. ... 1996 Ford Ranger SuperCab

My 1986 honda civic 1.5 jumped timing. I need to now what parts I might need to fix it and where the timing marks are. I think i need a new tensioner and replace any gaskets that i encounter. please help


Best thing to do if it's a overhead cam is get a professional to look at it and make sure it's done right because if you get it wrong and start it, it will cause alot of damage. if it's not just get the #1 piston to top dead center, and make sure the ... 1986 Honda Civic

I replaced head set #1 piston at tdc aligned colored links on timing with crankshaft and camshafts camshaft marks aligned with marks on camshaft bearing caps something prevent the engine from making a complete revolution


The pistons are hitting the valves. The Cams are out of time somehow ... 2002 Toyota RAV4
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.4992 seconds