Having problems with your Cars & Trucks ?

Tightening torque for Tata Xenon DICOR clutch pressure plate

\015 Clutch pressure plate retaining bolts - tightening torque\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Tightening torque for Tata Xenon DICOR clutch pressure plate


... Cars & Trucks

What are the torque settings for a Xh longreach ford falcon clutch plate and pressure plate


... Cars & Trucks

Clutch pressure plate torque setting


... Ford Laser

I have removed the gearbox from my 2000 MB 100 Van. I found the clutch plate has disintergrated. I noticed the Flywheel clutch pressure face looks like it will come off. Is there more to this clutch system than a flywheel, clutch plate and pressure plate system?


Flywheel bolted to engine, clutch disk and pressure plate, also has a throw out bearing that should be replaced at the same time.you don't need to replace the flywheel unless it is cracked though you should have it turned down at a machine shop. ... Mercedes-Benz Cars & Trucks

Torque spec for clutch pressure plate bolts


... 1991 Isuzu Stylus

Need torque settings for 2007 rodeo v6, for clutch pressure plate, bellhousing, rear driveshaft universal


Plate-59-78 nm bellhousing 8nm drive shaft front and rear 63nm ... 2004 Isuzu Rodeo

I need torque specifications for 1997 mustang, 3.8L,5spd (clutch pressure plate bolts)


Pressure plate to fly wheel bolts 20-28 ft lbs. ... Ford Mustang

What is the 2006 cobalt ss clutch flywheel and pressure plate torque specifications?


... 2006 Chevrolet Cobalt

Torque specs on hyundai accent gl clutch pressure plate


... 2005 Hyundai Accent 1.3

What is the torque for the pressure plate and the clutch and the transmission for a 2000 nissan altima?


... 2000 Nissan Altima

What is the clutch pressure plate torque - 2005 Kia Sportage


... 2005 Kia Sportage

I want to know how tight to tighten the bolts on the clutch pressure plate? Thankyou.


The bolts should be 12 mm. The manufactures don't usually give tightening tourques for the clutch cover but I think if you take them to 23nm you'll be fine. Make sure that you check them for stetch before fitting them and as its a rotating mass, make ... Mitsubishi Pickup

2003 toyota mr2 torque spec for clutch and pressure plate


... Toyota Cars & Trucks

Clutch pressure plate torque forester 1998 - Subaru Cars & Trucks


... Subaru Cars & Trucks

Looking for the torque specs for the pressure plate just replacing the clutch


15-25lbs there should be 6 bolts apply lock tite to bolts and then tighten them all down till they are seated. Pick a bolt(call that bolt #1) and torque it then in clockwise motion skip over the next bolt(bolt #2) to the third bolt(bolt #3). Torque b ... 1986 Ford Ranger 2WD

Daewoo 1999 1.6 clutch pressure plate torque setting


... Cars & Trucks

What is the torque setting for a clutch pressure plate on a 107 Peugeot?


... Cars & Trucks

I need the diagram, how much torque (if need) the bolts and nuts need in the clutch and pressure plate in 2004 rx8 manual transmission


... 2004 Mazda RX-8

Torque setting for clutch pressure plate to flywheel on 1995 toyota coaster 1hz motor 5 speed transmission


... Toyota Land Cruiser

1999 2.0L TD Suzuki vitara the clutch pedal was low and grumpy when pressed and hard to select 1st or reverse. plenty of movement in clutch slave arm and no fluid leaks to be seen.so i removed the gearbox to fit new clutch hoping its a pressure plate? but found the end or pilot bearing had collapsed with only 4 ball bearings found rolling about.Could the missing bearings be the problem as they could of worked them self into the pressure plate springs & so on thanks


Pilot bearing (pressed into flywheel) or release bearing (presses against clutch pressure plate)?\015\012Regardless, the repair is the same. Replace clutch disc, pressure plate, release bearing & pilot bearing. Most flywheels are available ... 1999 Suzuki Vitara

2002 Kia Sportage Car spongy clutch pedal Answer The clutch pedal is very spongy, and sometime has not pressure on the pedal at all when the vehicle... (More) The clutch pedal is very spongy, and sometime has not pressure on the pedal at all when the vehicle is running and I can't get it into gear. Also the clutch was slipping and very slow to get moving from a dead start, a short time later it began working a little better. Should I replace the clutch and pressure plate or is there an issue wit


The spoongy feeling is a defective clutch slave cylinder. Generally a cluthc will not slip because of a pressure issue with hydaulics. \015\012\015\012If the clutch is slipping with your foot off the pedal it defineately is time for a c ... 2002 Kia Sportage

1992 jetta, replaced gearbox,now clutch push rod will not move the pressure plate and pedal is on the floor, tried putting old trani back and the same thing happenned. Release bearing seems to be in the dissengaged position even though the clutch will not move. Checked out pressure plate with a new one at store and they are the same, i.e. no bent parts or springs etc.


Check for hydraulic resevoir iam almost certain it is fluid actuated and that would call for a piston in a slave cylinder ... 1996 Volkswagen Jetta

I recently changed my clutch and pressure plate and release bearing and found out later that the release bearing was spinning loosely on the pressure plate. I replaced the release bearing and now notice that the bearing is doing the same thing. When I press the clutch the noise stops. What can be the problem


I feel you need to back off on the adjustment rod for the clutch and make sure the return spring is pulling the arm back all the way ... Cars & Trucks

On my 2001 KIA Spectra the clutch won't fully release. It acts like the pressure plate is still partially engaged. The car wants to pull when the clutch pedal is fully depressed. Is this a failed pressure plate or a failed hydraulic slave cylinder?


Could just be low on cluch fluid or you may have to bleed the air out of the slave cylinder ... 2001 Kia Spectra

2001 Dodge 4x4 diesel 6-speed. Replaced clutch and pressure plate, now the starter won't turn the engine over.. Tried turning it over with the harmonic balancer, and the output shaft on the x-fer case. No luck, it is locked up tight. Flywheel, clutch and pressure plate all installed to spec. Tranny and engine mate tight. Why is the engine locked??


One problem pops into head when I think about your description of the problem. The bolts that hold the pressure plate to the flywheel may be too long, causing the engine block to interfere with the rotation of the flywheel. ... 2001 Dodge Ram 2500 Truck
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.2950 seconds