Having problems with your Cars & Trucks ?

Rattling noise tappet may have come out of place need to find out how to do this please

\015 Need instructions on how to get to the tappets please\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rattling noise tappet may have come out of place need to find out how to do this please


... Cars & Trucks

Engine noise there is a noise coming from the overhead cam. sounds like a loose tappet. the valve clearance may be a little tight rather than losse.( inlet 20) (outlet25) the noise only appers when the engine starts to warm up.4A FE engine. could you please help


Hi there , it can be lose . i think you better to check your cam shaft .\015\012there is one things your have to think about them \015\012- oiling system ( oil pump , pressure valve , oil type ) focus in these ... 2007 Toyota Corolla

I have a 2003 corolla. The windshield fluid does not spray. Actually there is no noise coming from the fluid motor at all. I think it may be a fuse problem but I can't find the fuse that controls the motor. Please help


Check in the engine compartment on the driverside. There is a black fuse/relay box.\012Also the washer tank pump could be broken. ... 2003 Toyota Corolla

Where could i find a vacuum diagram for a 1990 chevy caprice ..4.3 engine ...this car will buck jump then a bad loss of power and will die...wait a minute then then start and runs ok.....no service engine light comes on and computer test show nothing....some of the natural gas equipment is still in place and i was told it is a vacuum problem and needs to be put back the way it came out....please anyone with info on a vacuum diagram i would greatly appreciate it...thanks david


There could be a vaccum diagram in the engine under the hood. IF not I would go to Alldata,com. The get the information from them. The dealer might be able to provide a copy of it, ... 1990 Chevrolet Caprice

Fuel Problems To whom it may concern: I have recently developed a problem with my fuel system. I purchased some fuel from a common place and come to find out that the fuel filter had obtained the water. I then replaced the filter and now it died again and would not start could it be that it might either be the electrical grounding out or could it be i need to drain the fuel tank and start with a new one and replace the filter again? any help with this situation would be much appreciated.


I think the tank has water and you will probably have to drain it. There are water removal fuel additives on the market, but I do not know if they work or not. you can buy them at any autoparts store. ... 2004 Ford Focus

Passenger rear wheel bearng needs to be replaced.does this require special tools? I've just had a complete brake job ,new pads new rotors new drums and I have a recurring grinding noise coming from the rear wheels.upon further inspection from the brake installer he placed the tip of a screw driver to the wheel bearing spot and placed his ear on the handle of the screw driver and manually turned the hub and could hear this grinding noise.When I'm alone in the car there is no noise,but withtwo or


You can do this job your self with common tools. Auto zone carries the wheel bearing you need and can give you the step by step instructions to replacing the bearing. Here is a tip, to try to break the old wheel bearing from the axle. Just loosen the ... 2001 Toyota Corolla

2000 lincoln town car Clicking Noise Coming From Under The dash board sound like when you have your signal lights on but it is faster. use to go away when the car heats up. it is coming from the place where you plug your computer reader. the noise will stop when you thought the brake. Can any one help please?


This clicking is the Antilock brake system doing a self test. It's mentioned in the owners manual. Nothing to worry about but it should only take a minute and its best to let it fully cycle. Ned ... 2000 Lincoln Town Car

How to replace cabin air filter nissan sentra 2002? i don't found the location Do you have a solution to this problem? Share your knowledge with the FixYa Community today! Post Solution Please type the numbers below to complete your post: Can't read it? Try a different one. Type the numbers here: OK Popular Solutions for 2002 Nissan Sentra 2002 Nissan Sentra i need to find out how to get the ready... i need to find out how to get the ready codes for my 2002 sentra. The emissions place... 2 Solut


LOOK BEHIND THE GLOVE COMPARTMENT. Compartmet is probabily plastic and all you have to do is push in real hard to get them past dash board. ... 2002 Nissan Sentra

Noise engine noise with oil warning lamp on, This noise sounds like tappet noise, I got the cylinder head cleaned and changed the engine oil.after this we checked the entire oil line cleanes , the oil pressure meter is showing low pressure however the oil pump is ok.still the noise is there, we have cleaned all the oli line in the cylinder head , cam, and casings, I HAVE OPEL CORSA 1.4 2003 MODEL,I AM UNABLE TO FIND THE PRODUCT CATAGORY IN THE LIST BELOW , GIVING FALSE CHEVIRLET ENTRY , PLEASE E


This sounds like bad main and connecting rod bearing they are worn and when they become worn they make noise. Because of excessive clearance between bearing oil pressure drops therefore starving the essential parts of the engine of oil. ... 1998 Chevrolet K1500

1997 mercury mountaineer: There is a loud crunching noise coming from behind the drivers side front tire only when making right turns or going straight. the faster the speed the louder the noise. left turns make no noise. sounds like metal crunching and clanking on metal and you can feel the noise rumble in the car under your feet and in the steering wheel. I am not very mechanically inclined, but I am not mechanically stupid either, so any answer needs to be thorough please...


Check the axles and the axle that go from the tran to the front wheel drive box,had the same problem, removed the axle from the trans to the front gear box an noise stoped. ... 1997 Mercury Mountaineer

Need to change rear brake pads on mercedes benz vito van. Have managed to remove everything i need to. Putting it back together and they now brake does not work. Think I may need to change the cables but not sure how difficult it will be - any help will be much appreciated PLEASE NOTE ITS NOT THE E CLASS AS STATED HAD TO PICK SOMETHING BEFORE IT WOULD LET ME POST AND COULD NOT FIND THE VITO VAN BUT IT IS A 2003 VAN


I take youve changed the hand brake shoes in the disc as you say the cable, have you adjusted the shoes through the wheel stud hole. ... 2003 Mercedes-Benz E-Class

The ABS and Brake lights on my 2000 Silverado Z71 come on periodically. While I know there is no relationship with the fuel system and the braking system, these lights come on every time I have a rough start. I recently had the fuel pump changed and am still having some difficulty starting. Dealer said I may need to replace some fuel pressure regulator for an additional gazillion (dealer charges) dollars. I just find it odd that these lights only come on when there is a starting problem with t


One thing to check and is a common problem with these vehicle is, the side post batteries and corrosion building up in between the connections usually on the positive side. I would remove both sides and make sure that they are in fact clean and use a ... Chevrolet Silverado

I have a 05 Elantra 2.0 DOHC....At idle the engine valvetrain makes a loud rattling noise....If I rev the engine to around 1500 rpms the noise goes away, but as soon as it returns to idle the noise comes back....No other problems...No check engine light, and runs good otherwise...I have had the oil changed twice thinking it may be something to do with that, but no change....I read that it has valve lash adjusters, and no adjustment is needed..I thought low oil pressure, but no light at idle...Pl


May be your oil strainer is stock up or your oil pump is damage.i recommend use the f2020 powerlube to minimize the noise.search to www.f2020technology.com ... 2005 Hyundai Elantra

I Still have valve train noise in my '99 Chrysler Concorde 3.2 after replacing the timing belt, water pump, and hydraulic tensioner piston. Could it be the idler? The noise is Not coming from any other belt-driven device as they have all been disconnected to test various systems. The idler may well need be replaced as it has about .020'' play but rolls smoothly with no load on it. The clattering noise happens about 600 to 1200 RPM. HELP!


Probably the idler, i change it when i install timing belts..could be a vavle tappet...carefull use a broom handle as a stetho to listen at the valve covers and the timing gear cover ... 1999 Chrysler Concorde

I have a transmission leak & need to know what the part is called by describing it. It may be some sort of shifting sensor, its a small box in the front posibly with wires coming out of it, I have a gasket leak & need to know the name of this part & find out if I can just get the gasket or if I need the whole kit but dont know what this part is called.


If it leaking you need to check for cracks and holes. If you can't find them and its leaking around the seals you need a new gasket. Hope this helps!?\012\012\012Please rate solution - Thanks. ... 2000 Dodge Stratus

2004 Hyundai XG350 I drive aprrox. 60 miles a day to work in Phoenix, AZ. Stop/Tail Light Failure Warning light comes on when I step on the brakes. Had new front brake pads installed July 2009. brakes seem ok - no squealing noise but may need new pads? Not sure how often they need to be changed out . Can you advise on this? Also, how often do struts need to be replaced? Had front struts installed July 2009 . Also how often should anti-freeze be added? Last time was a year ago when i


... Hyundai XG350

Owners manual.... Where do I find a 1988 Beretta GT owner's manual? When I bought the car it didn't come with one. Been looking all over the place online, but can't find anything to print one off for free.If anyone knows a site that I could print off a manual for my car that would be great!!! PLease let me know. Thanks!! Collette


Ebay motors is the best source around for used owners manuals. I got one for my 84 corvette that way, 1st try. ... 1988 Chevrolet Beretta

Driver side heated seats keep coming on when they want to, on my 2005 Chevy Suburban Z71. They get really hot. I have found that if you leave the base of the seat on the low seating then the back or lumbar will not come on for a while. I need help in finding a solution. It is a driving hazard. Almost 2 years ago I had them change out the switch so I don't feel that is the problem. Please help me. Blood Boiling


The problem could be the drivers seat module.It is under the seat and controls the drivers seat functions.There is a service bulletin for seats that will only work for a few minutes and then shut off by themselves.The fix for this is having the drive ... 2005 Chevrolet Suburban

I've got a 2003 Hyundai Accent and I've been having problems with the front end. There's a lot of wobbling mainly coming from the passeneger side front tire. There's no noise associated with it. It's causing a bit of vibration and results in not a very smooth ride. I've taken it in to a couple of places. First place (dealership) said I needed new tie rods and to get my wheels balanced. Did that and the problem went away for a couple weeks. When it came back I took in to another garage and they s


Check the CV shafts. To do that turn the steering wheel all the way and slowly take off, radio off, and listen for a "clunking" type sound. The turn the wheel the other way, all the way and do the same.\015\012Kinda' sounds as if the CV shafts ... Hyundai Accent

Suzuki XL7 - Diesel sounding engine very loud noise. Initially started as a "tick-tick" noise. Currently at a Suzuki dealership (over a week long) and I am told that the problem is a inferior oil filter was used and it broke up. The pieces went into the engine and they need to clean it out. Then I was called back and said that some parts in the cylinder may have come apart and are foating in the engine when it going stopping the oil from getting to all of the engine. Have you ever heard of this


As a mechanic point of view,i have never heard that before,to be truthful and logic it is false,they are trying for an excuse. ... 2007 Suzuki XL-7

Low coolant My car is a saab 900 s and in the info says coolant low. what do i need to fix to stop this from coming up on the info. i took to a saab dealer but they didnt tell me what is the name of the part that i need. please help me find out. THANK YOU


Beleive or not if your coolant level is corect its probably whats called " low coolent sensor " which is usually mounted on side of coolant resevior hope this helps ... 1998 Saab 900

Hi. I have a 1997 carina e cd auto, one of the aircon pipes was leaking which I had repaired.I now find that the air con i not very cold.A friend suggested it may be a fuse for the A/C motor.I have tried to find a fuse but cannot locate one in the car.Also.I have recently noticed that when travelling between 60-70 there doesnt seem to be much pedal left and I have to wait for ages If I need to accellerate as my foot is right down to the floor. Can anyone please help with problems? Harry


One problem that occurs when dealing with a major leak is that most repairs dont take care of the lost oil during the leak i dont know if it was done but it is very necessary to reprenish the oil lost it has a very important and it affects cooling al ... 1987 Toyota Corolla 2 Door

My o6 Corvette's crank pulley has moved forward. I was told the pin may have come loose or the bolt may be broken. A lot of Vette's have had this problem can I drive the car until it's fixed there is no noise and the only reason I noticed it was because the belts were riding forward on the tensioner pulley. Can I just have it tightened or will I need to get a new bolt and pulley.


The balance is bad it's self, no pin no broken bolt. I wouldn't drive on it. The belts will have lots of extra wear and may brake. This is not a job that can be done in your drive way. The craddle needs to come down to move the steering rack to b ... 2006 Chevrolet Corvette

Air Conditioner 1999 Buick LaSabre. There is cool air coming out of the vents be the windshield but does not cool the rest of the car off. The vents on the driver and passenger side do not work at all. I took it to a auto place and they said $110 for putting freeon in and charging it. Then they said the vents were a electrical problem and would cost me a ton more. I know that I need to put more freeon in it and if there is a leak get it fixed then I need to find out it the vents are being blocke


To answer your question , yes that what needs to be done. Sounds like the vents aren't blocked, just that the control motors aren't opening them.  It may be a bad switch, lose wire.  So to get it working as you were told you would need that ... 1999 Buick LeSabre

My 1999 pontiac montana has a loud almost airplane sounding noise coming from the engine while driving. It is at its worst when steering straight or to the left. It doesn't make noise when steering to the right. Please help on what the problem may be. thank you


You need to replace the wheel bearings ... 1999 Pontiac Montana
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.7758 seconds