Having problems with your Cars & Trucks ?

1996 GA15 head removal - idler sprocket?How to support it to lift head off.

\015 Need to unbolt it to lift head. Must keep lower chain engaged. How do I support it? Not much clearance. Do I need to loosen lower chain tensioner to get it off the shaft?\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1996 GA15 head removal - idler sprocket?How to support it to lift head off.


... Cars & Trucks

How do you install gas charged lift supports for a 2005 Dodge Grand Caravan hatch back. I have Strong Arm brand lifts and the bolt are in the lift. It looks like it should just screw into the hole left by the by removing the old support, but it will not match up. I can screw each one separtly but when you get one in the other will not match up, the second one will go in part of the way but not all of the way. Any advise you can give me will be appreciated.


... 2000 Jeep Grand Cherokee

I have a 2001 vw jetta vr6 glx wagon with a manual 5 speed, the water pump bearing has went bad causing the belt to come apart so I need to replace the pump. What literature I have found lists a 50+ step procedure of removing and relocating engine bay items and unbolting and lifting the engine and trans to the driver side to remove the pump. Other information says that the engine can be unbolted from a passenger side dog bone support and lowered enough to allow the removal of the pump because


The engine can be unbolted from a passenger side dog bone support and lowered enough to allow the removal of the pump because the frame blocks it in due to proximity. This is the best & correct procedure. Good Luck! ... 2001 Volkswagen Jetta TDI

Need to remove hatch lift support on the 97 Hyundai Excel


Most gas lifts have a small clip at the end of the shaft right next to the ball Pus it in will release the ball . I have un screwed the ball from the vehicle to get the struts off and when I have done that I can see how to remove them easier.Remember ... Cars & Trucks

How do you remove hatch lift support to replace


Lift supports are press on and pull off! If you look at each end of the lift supports you will see a small metal band that goes around the lift support, take a screw driver and get under neath that band and pry it off, this band holds the support ont ... 1994 Ford Probe

Dismantling daughters Suzuki Alto 1989 to fit new head gasket due blown between cyl 2&3. Success removing inlet manifold after long time on lower center bolt. Considering if it should have been a stud? Cannot get direct access to front pulley on c/shaft.How is pulley removed to allow cam belt dismantle? Lift the body a little to get access for socket onto c/shaft bolt? Fri 6 Aug today 5pm so monday & L8tr later soonest for parts, here in central north island New Zealand. Have no technical da


... 2005 Suzuki SX4

How do you remove the battery from a 1999 dodge caravan? I removed the terminals but it won't budge to lift out? There is no vivible support arm?


At the base of the battery, you should see a battery hold-down. It has one bolt going through it. Remove the bolt and the hold-down clamp and the battery should come right out.\015\012\015\012I hope this helps! :) ... 1999 Dodge Caravan

I am a old retired mechanic wanting to change spark plugs on my 2000 4 cly Tacoma trucck. When removing first wire it just lifted out with out any sign of being attached to plug. I got confused and put wire back into head cover and it seems to run ok what is going on here???/


In some cases the plug wire do coe off that easy. however this is most often not the case. ... Toyota Tacoma

How to remove the head on a GA15


... Cars & Trucks

Removal / replacement of tailgate lift supports


There will be either a bolt at each end or a spring slide, if it is the slide just push it along with a screwdriver and the support will just pull off. make sure to prop the tailgate or get someone to hold it up for you or it will fall on your head a ... Chrysler Pacifica

Trying to replace the idler pulley on 1999 Buick PA with supercharger. This is on the supercharger belt. The pulley i am trying to replace is directly behind the engine mount bracket. I have removed the engine bracket bolts, disconnected the engine bracket from the motor mount support, and removd the bolts holding the motor mount to the frame. i also loosened the right engine mount, and jacked up the passenger side of the car. I still cannot get the engine bracket off of the engine enough to get


... 1999 Buick Park Avenue

Window switch removal w/out breaking plastics: Do I squeeze with two flat head drivers and lift from middle or top of sw/block ?


Take of all panel and then you can remove the switch from bottom without damaging or scratching any plastic. ... Saab 9000

I have a 1999 ford f150 need to to remove the lower idler pully what kind of bolt is that looks like some kind of star headed bolt what is the size?


That would be a torx bolt,size go E6,E8,E10,E12 and so on,find correct one,dont know exactly what size it in ... 2000 Ford Focus

I need to replace the water pump on a 1995 Buick LeSabre. I understand that I need to remove the front motor mount to accomplish same. How do I safely lift the engine enough to do so? Where do I support the engine from below?


Into 3rd hour.\015\0122 lower Car Motor mount bolts just are not budging\015\012WD-40 is all I have to loosen the bolts, worked for the top 2, but I got to use the 1/2" drive on them, 3/8" driver is all that fits on the lower bolts (with the help of ... 1995 Buick LeSabre

How to remove hydraulic lift gate supports - 2000 Lincoln Navigator


... 2000 Lincoln Navigator

My 1995 oldsmobile aurora idler pulley need replacing. I cant get the bottom 13 mm bolt off the motor mount plate with a wrench because some body stripped the head. you cant fit a rathchet in there and the motor dosent drop or raise enough to get the bolt past the frame. do i have to remove the hole motor?


... Buick Park Avenue

Trying to remove the lift supports for a 2000 toyota celica


... 2004 Toyota Celica

Rear lift door motor does not work. motor does not appear to run. Left support cylinder appears stuck, whereas right works as as "shock" as expeceted. Where is fuse for motor? where is motor and how to remove?


I'm looking at wiring diagram that shows a circuit breaker behind center of dash for Your backdoor motor. There is also a 50 amp fusible link that's located in the Fuse and Fusible Link Box Left Rear of Engine Compartment near Battery. Also I will se ... 2004 Infiniti QX56

I am trying to remove the door panel for the rear door of a 1988 Olds 88. I think everything is off except something at the arm rest. I don't see any screw heads there. I'm guessing there must be a stud of some kind. Do I lift the panel, push it to one side or the other??


It will lift up if all retaining bottons on the side are removed ... 1988 Oldsmobile Delta 88

How do i remove existing hydraulic lifting support arms on the back hatch door


You will see spring clips at each end to pry out. them remove them ... 2003 Chevrolet Tahoe

Instruction on how to remove old rear hatch lift support on 1987 CRX Si


... Honda CRX

Trying to remove head to replace head gasket on 2.0 L non-turbo engine on '97 Mitsubishi Eclipse. My Haynes manual says to remove the intake manifold stays and the head can be removed without removing the intake manifold from the head. It does not mention the black plastic box that is mounted over these stays. I took off three nuts that seem to hold this box in place, but it does not come off. What is this box and how do I remove it to get access to the manifold stays?


Jack up the car support with jack stands remove cover shield to view the underside of the box/intake manifold, make sure to use a drop light to uliminated the underside of the assembly, this should allow you to see what is connected to the box or the ... Mitsubishi Eclipse

Oil leaks between head and block. Removed head. Can't find cause.


Where is oil pressure switch/sensor on 2001 nubira ... 1999 Daewoo Nubira

I have a 2003 gmc envoy SLT 4.2 L6, and need to remove the head and I dont know how to deal with the timing chain? a few of my exhaust bolts broke and I would like to remove the head! how do I remove timing chain and still keep the timing chain from falling into engine and how do I seperate the chain to remove the head. And what other surpises are in store for me?


Check this procedure.... Timing Chain & Sprockets-Removal & Installation for 4.2L Engine\015\012\015\012NOTE\015\012\015\012The following procedure requires the use of the Crankshaft Holding tool No. J-44221 and a suitable to ... 2003 GMC Envoy

I have a 1995 Suzuki sidekick 16 valve 1.6 engine, that I am going to replace head gasket. I have removed everything except the timing belt, distributor, and head. My question is why is it that in the Haynes Manual it states that on the 16 valve engines you have to remove the camshaft and intake rocker arms. Is this correct? and why does the distributor need to come off also? both of these parts are attached to the Engine Head. I would assume that just by removing the head bolts the whole


It is known that you may not have a head gasket leak if you are not over heating not loosing fluid but you find water in the oil they have hemi heads and in between the cam valve cover is a two piece gasket and i have seen them leak when ya go th ... 1995 Suzuki Sidekick
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.7765 seconds