Having problems with your Cars & Trucks ?

I have a 1992 wellcraft eclipse 186

\015 The boat when running stalls out when put into forward , but doesnt when put into reverse\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A P0300 OBD CODE I DID A COMPRESSION TEST TO ENGINE AND IT PASS THE TEST,I DID CHECK EGR VALVE,CHANGE SPARK PLUGS,IGNITION WIRES, CAP AND ROTOR, I DID CHECK TPS SENSOR MAF SENSOR,FUEL PRESSURE,AND OXIGEN SENSORSI I FOUND THAT ON BANK 1 BOTH SENSORS (UP STREAM & DOWN STREAM )WORKS NORMALY BUT ON BANK 2 THE SENSOR 1 CHANGE FROM 0 TO 600 MILIVOLTS BUT NO CHANGES FROM RICH TO LEAN &SENSOR 2 HAS 0 MILIVOLTS & NO CHANGES FROM RICH TO LEAN SO I SWICHT SENSOR TO TEST THEM FROM BANK 2 TO BANK 1 AN


... 1997 Nissan Pathfinder

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

Ford Focus engine diagram Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V


... 2001 Ford Focus

96 cirrus 2.5. No spark. distributor has 2 wire connectors , 1 has several wires , the other has only 1 wire. When I turn the key , the one that has only 1 wire gets 12 V , but it only lasts for a couple of seconds , then goes down to 0 v . My thinking is that this wire is to energize the coil , and should stay at 12 V to give the coil power to make spark for the Distributor. Can anyone tell me if that is suposed to be a continuos 12 v or not .


Ignition module ... 1996 Chrysler Cirrus

Diagram for 2000 mitsubishi eclipse 2.4l where is bank 1 sensor 1


... 2000 Mitsubishi Eclipse

Stage 1 camshaft on 420a eclipse 95? do i need new ecu?


... 1995 Mitsubishi Eclipse

Where is bank1 sensor 1 (O2 sensor) of 2003 Mitsubishi Eclipse


If its a 4 cylinder it will the 02 sensor closest or if not in the exhaust manifold ... 2000 Mitsubishi Eclipse

Code P0051 I asked earlier but here are more details. ITS a 2007 Eclipse Spyder GT V6, the sensor out is BANK 2 SENSOR 1. Is this in front of the engine or behind? I am getting different opinions. Any picture available anywhere that shows Bank 2 Sensor 1 in the car itself?


... 2007 Mitsubishi Eclipse

I have a 2000 toyota celica gt, has a misfire cylender 1 has 0 compression, cyleder 1, 130 on 2, 80, on 3, and 90 pn cylender 4, any solution for problem?


... 2000 Toyota Celica

Dodge Durango 2004, the volume on radio will not go further than 1 on the graph, and also no sound in speakers.... can adjust between 0 and 1 ?? Any idea what to do ?


... Dodge Durango

Using my OBD II on 2000 honda prelude trouble codes PO401 & (PO401 pd) all reads MIL on, monitors, 1 INC, EVAP, 7 ready, MISFIRE, FUEL, COMP, CATLYST, 02 sensor, 02 HTR, EGR. Will be cleaning out EGR, BUT do I need to replace my Solenoid? My prelude stalls and ideals out of first gear. (Autotranny). Is this stall caused by these trouble codes? Also with 1 pending code, what do you recomend? I ran car and used OBD II a 2nd time and only change was (0 inc) and 8 (ready).


... Cars & Trucks

Hello, I have a 2000 Mitsubishi Eclipse GT V6 3.0 that the service engine light soon has come on. A mechanic put his diagonistics machine on it and the error code P0135 - Heater circuit, bank 1 sensor 1. I got a new O2 sensor from a friend that works at Mitsubishi that used my VIN to ensure correct part. I changed the O2 sensor on the top of my exhaust manifold. There is also a lower one and one near the firewall more on the left side pf the engine as you stand in front of the car. For the code,


... Mitsubishi Eclipse

Propercrankpositionfor correctbelttiming is there a timing mark onthe crank pulley for refrence to line up with a notch on the engine ,besides the flyweel mark? i am puzzled because i have already bent some valves & dont want to repeat my mistake. i have put the #1 piston at TDC, flat with deck ''0'' deck is this right or should it be slightly below ''0'' deck hight and or should the key way be at 12:00 position. please help me P.S, this a 89 honda accord 2.0 carb.3V A20A1 engine


Send me your email address and I will send you the proper timing positions. I can copy them from mitchel and email it.... ... 1989 Honda Accord 4 Door

Im not getting a spark in my cylinder 1 on my nissan 300zx and now im getting a mis fire and its also idleing in the middle of 1 and 0 what could it be please help


... 1993 Nissan 300ZX

I pulled the #1 spark plug and put my finger over it and had someone turn the motor over until the pressure moved my finger. I then used a socket and moved it the rest of the way by hand until the mark on the pulley was lined up with tho 0. I put a straw inside the #1 cylinder to make sure the piston was at TDC and the piston was not near the top. I had someone hold the straw and turned the motor by hand and got the piston to the top and was pushing the straw out but now the mark on the pulley i


Yes it can be wrong is the crank in right it could be 180 degrees backwards i have seen it happen. but i dont know how much work was done before this problem email me some more info and i can help you further ... 1985 Chevrolet Chevy

On my girlfriends 1992 Honda Accord we've noticed it has a shuttering problem almost as if lack of gas? It only happens when the car comes to a complete stop. The R.P.M's drop to 0 then bounce from 1 to 0 repeatedly


Sounds like your Idle Air Control Valve may be bad/faulty. ... 1992 Honda Accord

Where in the Bank 1 Sensor 1 located on a GTS Eclipse


It's the first O2 sensor that's in front of the catalytic converter. If it's a V6 car, it will be the one that's on the same side as cylinder #1. ... 2003 Mitsubishi Eclipse Coupe

P171 code p171 lean to bank 1. 2003 Infiniti G35. Maf sensor seems to be within range. Only thing I noticed on my scanner is my long term fuel trim was 37.5% and 0 to 3%. Short term fuel trim was 99% and 0. I checked for vacuum leaks with no luck. I'm leaning towards bad O2 sensor or clogged/bad injector.


Yes i would say the same if you are sure there are no vacuum leaks ... Infiniti G35

My 2003 nissan sentra has trouble starting. It usually starts and dosen't die by the second or third try. The speedometer will jump from 0 to 1 or 0 to 2 when I am driving and then cut off. Or sometimes the speedometer will jump up and down as the car jerks. When I press on the gas my car makes a coughing sound. I am afraid my car is on the verge of breaking. What do I do?


Good day, try to check the coils spark plugs air filter i hope this tips will help you. ... 2003 Nissan Sentra

Radio my code is 0319 How do you enter the 0 when it initially comes up to 1000 and there is no 0 on the first button, it goes from 1-9?


Using the station buttons , left to right , 1st button is 1000's, 2nd \015\012button 100's, 3rd is 10's, and 4th button 1's, push each button until desired\015\012number from each button , once you have the number in the display it\015\012should unlo ... 1993 Volkswagen Cabriolet

I have a 1998 mitsubishi eclipse rs and the check engine code P0301 pd (misfire in cylinder 1). I've put in new spark plugs and wires and the fle injecter is working fine and its still misfiring. Could it be the ignition coil that's cousing only cylinder 1 to misfire?


YEP BAD COIL CLOGGED FUEL INJECTOR AND INTAKE LEAK TO CYLINDER 1.TRY CLEANING FUEL INJECTORS.IF STILL MISFIRE DO A COMPRESSION TEST TO THAT CYLINDER YOU COULD HAVE A MECHANICAL ISSUE. ... 1998 Mitsubishi Eclipse

Working on an 03 Mitsubishi Eclipse Spyder. Does anyone know where the Bank 1 Sensor 1 location is for the Oxygen sensor in this car?


... 2003 Mitsubishi Eclipse Spyder

I have a 1987 Plymouth reliant with an older a/c compressor. I've had the system evacuated and it holds pressure. I've also had it converted to 134 as well. When I add freon to the system, it registers high but when the compressor turns on, the pressure drops to 0. I also have to bypass the high pressure switch to get the compressor to engage. Before it would re-cycle every 1 minure or so. The parts to the a/c system are very old. Intially, the pressure was about 40 lps and now it shows in the 1


First the low side should read 30 and the high should read 230 PSI or up to 275% f. DEPENDING ON THE AIR TEMP. did you change oil for the R134a? if not you will have to empty the dryer and compressor and replace the oil and you will now have to repla ... 1987 Plymouth Reliant

98 buick lesabre oil pressure dropped to 0 and engine died. added 1 quart oil, waited 30 minutes, started and drove 5 miles then oil pressure dropped to 0 and engine died. does this sound like a bad oil pump? where is the oil pump and is it hard to change for a "handy" person? thank you.


My sister had the same problem. There are 2 sensors that can cause this when they go bad. One is the oil pressure switch, which is located near the oil filter. When the PCM reads this switch, and gets a low reading, it will automatically kill the eng ... 1998 Buick LeSabre

2003 mitsubishi eclipse bank 1 sensor 2 - Eclipse Spyder Mitsubishi Cars & Trucks


... Mitsubishi Eclipse Spyder
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4320 seconds