Having problems with your Cars & Trucks ?

How to repair spider gear problem - Cars & Trucks

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for Cars & Trucks

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to repair spider gear problem - Cars & Trucks


... Cars & Trucks

I have a 99 bravada. the truck will randomly start right up then die after a few seconds. however, if i put a little car in the intake, it starts right up and runs fine. ive been told its spider injectors, but that doesnt seem right because wouldnt the car stop running once the gas burned off from the intake? im guessing its my passlock system but not sure. im a single mom and i dont wanna spend money on a repair and still have the problem. PLEASE HELP!!!!!


I would start by having your FUEL PRESSURE checked. I think your fuel pump is bad. ... 1996 Oldsmobile Achieva

We are looking at getting a used truck, but the major problem is that it will not move in reverse. It moves forward fine, but when it is shifted into reverse (shift sounds fine, sounds like reverse has been engaged) the truck does not move. The seller says that the problem is that the spider gears are shot?? I looked up spider gears on the net and it seems like they have nothing to do with this problem. Oh, and when 4X4 is engaged, the reverse apparently works?? I would greatly appreciate


This is an indication of a transfer case issue and should not be to much to repair. If it works in 4WD(to which I would want proof before purchase) then at least it is not a transmission issue. You are also correct in saying that spider gears do not ... Chevrolet 1500

Am having a problem with my car Honda1997/1998 mode V6 Audmatic.when l start the car it start moving on change to gear 2 it start firing it self for like 5sec, then after 5sec it change again and then cut again and change again for like 5sec, then l took it to my Expert for repair then he found that the TCM AIT gear position switch circuit is open and incorrect gear ratio, but the expert can not see were the TCM AIT gear circuit is. Pls could u help me point out were the problem met be or were t


Well if an expert told you and you trust and believe in him or her? I would go to part store and purchase that switch and then you would have a identity on it after all it is not like your going to need or use this switch.This method I suggested has ... 1997 Honda Accord

I had engine work done and a new clutch installed on my 2002 WRX. About a month after taking the car out of repair, my transmission got stuck in 2nd gear while I was driving. I heard a loud noise and it felt like the engine dropped off the car while I was moving; luckily I didn't get into an accident. The repair shop claims that the new clutch kit they installed has nothing to do with this problem of the transmission being stuck in gear and not budging. I have heard from others that improp


MORE IN FORMATION IS NEEDED TO DIAGNOSE THE PROBLEM . IF THE ENGINE IS SWITCHED OFF CAN THE GEAR SELECTOR LEVER BE MOVED INTO ANOTHER GEAR ? DOES THIS PROBLEM ONLY OCCUR WHILE THE ENGINE IS RUNNING ? I HAVE DON'T BELIEVE THE PROBLEM IS RELATED TO THE ... 2002 Subaru Impreza

Actually, this is not a car problem. I know from experience most 'car guys' know how to repair lawnmowers as well. Since you don't have a listing for lawnmower repair well, you get the rest.... I need to replace the back (drive) tires on a Toro Super Recycler Walk-Behind Mower model 20042. I have the correct rear wheel's but I need to find out how to remove the old gear and place it on the new tire. I've tried using a gear puller, but that doesn't work. I'm assuming I need to buy a new gea


Have you checked the Toro web site? I looked and found the rear wheel assembly and it looks like the tire, wheel and gear come as one assembly.\015\012Here is the web site you can look up the part and see the drawing. ... Chevrolet Camaro

I have a 1999 5-speed manual transmission Chevy Cavailar and I am having problems putting the car into gears. There is a grinding noice when i shift the car into all gears, especially reverse. There seems to be very little tension when I press on the clutch. Is this likely a problem with the clutch, traney, or shift cable? What would be a good est on the cost of repairs? Thanks


I am guessing from your explanation that your clutch is gone. Do not drive it if it is grinding as you say - this will destroy your gears and require a transmission as well as a clutch. Call your chevy dealer for an estimate - they have books with es ... Chevrolet Cavalier

Transmission temp high, periodically rpms rev high like not in gear. In drive prms rev up doesnt seem to get out of 2nd gear. In second gear the problems are mininal. In drive car keeps sounding like in neutral, then kicks in then back to no gear etc... doesnt make any"kick" noises when this happens, all you notice is the rmps rev high and car is truck rolling. I check fluid and appears to be good. Help!


... 2005 Cadillac Escalade Ext

Rebuilt top half of engine and rebuilt transmission. Car revs to about 3000 RPMS when accelerating. The car will then slip into gear and run smooth. Transmission guys claim it is a problem with the motor. The car never reved high after the engine repairs until the transmission was rebuilt. Is the problem in the engine or transmission?


Sounds like the trans is slipping. ... 2001 Dodge Intrepid

Cars & Trucks Logo * Print * Email Problem with Cars & Trucks 2004 pontiac sunfire 2.2 standard transmition, clutch wont release to permit shifting into gear, cause the shifter roll pin to brake, is there an easy way to remove the broken roll- pin without removing the clutch assembly


... Cars & Trucks

Transmission questions I boughta 1992 f150 with a 302. The guy put a c6 tranny in it but it was out of a floor shifter truck and mine is a column shifter ( automatic). The gears are backwards in the truck, park is low and low is park. I was wandering if there was a peice to fix this problem or will i have to tear into the tranny? If so, where can i find the partor what repairs do i need to make in order to get the problem fixed? Also, is there anyway you can tell me what type of tranny came out


The shift plate that attaches to the transmission just needs to be pulled off and rotated 180 degrees,So if it is currently facing up,just face it down and reattach the linkage. ... 1992 Ford F150 SuperCab

This is my dads car.. The battery was dead and the truck wouldn't start so we jumped it. After the extra help it started right up no problem, but once he tried to put it in gear the truck would just die. He's been also having reverse problems which i'm not sure if they are related at all. But there is no reverse what so ever. All fluids are up to spec. So why would the engine just die once there is load on the motor?


WHAT IS THE TRUCK ,YOU MIGHT WANT TO REMOVE ALTERNATOR AND HAVE IT TESTED.\015\012\015\012THE REVERSE PROBLEM ,DOES IT WORK AT ALL IN REVERSE IF NT IT COULD BE SUN SHELL GEAR STRIPPED ... Nissan Pathfinder

My MR2 Spider 2002 has a problem with Clutch cable which is in Clutch release Cylinder of the actuator, it is not working 100% which is not making a full Clutch activation, whenever I put the gear in S position the car RPM slow Down little bit and the car engine goes down when I release the stop petal, so far I fill a kick. Can anyone help me with this problem?


... 2002 Toyota MR2 Spyder

A few weeks ago, my 1998 Toyota Corolla (314,000 kilometres or about 196,000 miles) began jumping out of 5th gear, whie driving. It's almost as if the linkage need adjusting or some spring has gotten weaker through use. I am concerned that continuing to drive the car like this, could eventually lead to a more costly repair. There is also the safety issue, as it jumps out of gear while doing highway speeds. Someone please tell me it's a common problem and inexpensive to repair. All opinions


This is a problem inside the transmission and will not hurt performance but is a hassle. The problem is called a synchro. It is a brass ring inbetween gears that allows for smooth shifting and allows the gears to stay engaged. Take it to a trusted tr ... 1998 Toyota Tacoma

I tried to charge my car battery with a Chicago Electric charger model 66783. I followed the directions for charging the battery in the vehicle. After selecting the charge rate of 10 AMPs, the ammeter pulsed back and forth between zero and about 9 AMPs. The 'Charge Complete' light cycled on and off also. This is not consistant with what the directions describe is supposed to happen. Do I have a charger problem or a battery problem? I have not driven my vehicle (1954 Chevy truck) for about 6 mont


Relax, the charger is working fine. What it is doing is charging the battery to 15.5V. During this time, the "charge complete" LED is off, and the current meter shows the needle going to the right. When 15.5 volts is reached, the current is shut of ... Chevrolet Classic

Hi i really hope u guys can help i got a 1998 audi a4 2.4 auto i love the car to bits until my box went got it repaired has never been the same since, 1st problem when i drive the car loses power as if the atf oil is to low so the car revs really high and sometimes kicks really hard into gears up and down shift. 2nd when i start the car an emergency light pops up then disapears but sometimes the car wont start please any help will greatly appreciated been 4 months at mechanics.


Probably low atf and all of the dash lights and idiot lights should flash momentarily during startup ... 1998 Audi A4

Has anyone had a problem getting the gear shift out of park? Several people had difficulty getting the gear shift out of park to drive the car. They would have to jiggle the gear shift back and forth before they could get it into drive. This happened on more then one occassion. The gear shift had to be repaired after someone took the cap of the shifter and manually changed the shift to drive.


Make sure the brakes is depress fully ... 2005 Chevrolet Aveo

Starting from the stop sign tonight I gave the car gas and the tranmission didn't respond for a few seconds then kicked in. Noticed after that then when stopping the car when the car shifted into gear I felt alittle jolt.does the transmission need total repair or just a tune up? I checked the fluid and all is full. 1994 pontiac firebird 6 cyl.auto 119000 miles...just bought the car in feb this year, and didn't have the problem then..


... 1988 Pontiac Firebird

Clutch shudder I have a '97 Subaru Outback Legacy. 2 weeks after I bought it the head gasket blew. During that repair I had the mechanic replace the worn clutch as well. Ever since the car develops, no it is not there after every fix, a shudder in first AFTER the car warms up. About the third time I was going to take the car back again for the same problem, the clutch threw a spring and froze my clutch. I destroyed my 2nd gear getting of the highway. I then took the car back to the same me


Ask the mechanic if the clutches both came from the same source and if they were rebuilt units from the same re-manufacturer. The material used to resurface a clutch can cause this results. ... 1997 Subaru Legacy

Shifting problems on my 2000 Subaru Legacy Wagon. 4th Gear slips out, won't hold in at all. 3rd grinds when I shift it into gear, but slides in w/o the noise if I let the car slow down for a couple seconds. Shops are talking about opening the transmission and replacing the forks, bearings, gaskets for 3rd and 4th gear. The last mechanic, subaru-trained, said since it was also making noise in 1st gear, it would be worth it to get a used transmission - repairs would be too expensive; we'd open it


I would buy a used Trans and fix the other one over time. That way you can take it apart and it might not take a lot of money to fix it. Then you can sell it or save it. Also you may look at the different trans to put in yours. Maybe a Legacy GT 6 sp ... 2000 Subaru Legacy

My 1994 Ford Explorer has been having trouble going into gear. I have to give it gas and them it would kick into gear. Once in gear, there was no problem. I stopped on the way to work at an auto mechanic. He checked the fluid and told me it was most likely toast. I got he truck to go again (getting harder and hard to get going) and made it to work. When I went to go to lunch, the car backed up, but was not going into forward gear. The new mechanic says I need a new transmission. I guess I shoul


I would drain trany fluid and filter and put a quaurt of lucas trans slip lube and new fluid in it first and try that ... 1994 Ford Explorer Limited

My jeep grand cherokee is having problems shifting gears. it starts off fine then at some point it will **** will driving then the shifting problem beings. sometimes it happen if i have to make a sudden stop. Or if i am driving steady and hit a small dip in the road, or if i am trying to speed up. but if i cut the truck off and back on it starts off normal. I put in shop once they, repaired TCM wiring harness but the problem came back 6 months later. help me please.


If your hitting a bump and it is controlling the shifting , then the problem is in the wiring again. If you know what and where they did the repair. check this area. Most likely they didn't do a professional job that you paid for. Professional is sol ... 1999 Jeep Grand Cherokee

I RECENTLY STARTED HAVE PROBLEMS WITH MY 2000 SIERRA 1500 WITH A 4.3L V6 ?W? MOTOR CODE. THIS IS A CFI ENGINE WITH THE SPIDER INJECTOR SET UP. OK LET ME GET TO THE POINT. I HAVE A NO START CONDITION IF THE CAR SETS MORE THAN TWO DAYS. SOMETIMES AFTER 15 MINUTES THE TRUCK WILL START. BUT RECENTLY WENT ON VACATION AND THE TRUCK SAT FOR THREE DAYS! BUT RIGHT BEFORE I WENT ON VACATION I WAS DRIVING HOME TO DROP OFF MY TRUCK AND I LOST ALL GUAGES THEY ALL WENT DEAD. AS I WAS DRIVING THEY CAME BACK


Sounds like a bad ground. Check your battery cables, make sure they are on tight, and not corroded. Check the engine compartment, and everywire that is directly on the body or engine, take it off and wire brush it. Next, go in the cab, and do the sam ... Chevrolet Silverado 1500

2002 Dodge Carvan 3.3 liter was traveling 75 mph when car seemed to start coasting, no increase in speed with more RPM. Managed to get out of traffic but car will not move forward or reverse. Check engine codes show P0740 Torque Converter Clutch Solenoid, P0734 Gear 4 Incorrect ratio and P0700 Transmission Controll System MIL required. Car has 151,000 miles and I am questioning whether I can justify major transmission rerpair. Could this be a minor problem or a major repair require transmission


Having owned a trans shop in the 1990's,I would get ride of it\015\01280% of my work,was Caravans transaxles.\015\012Very unsafe vehicle,in the event of an accident,all van type vehicles are. ... 1998 Dodge Grand Caravan

Hi, i have a 1997 s-10 Blazer 2wd suv. I recently had the spider injectors changed and now the truck starts in 2nd gear and will not shift into 4th. Does any kn ow what this may be? All I am getting is runaround from the mechanis that installed the spider injectors. It did not have any shiifting problems until I picked it up and drive it about 10miles.


HELLO \015\012 When the truck start in second gear it is is in limp home mode, as to the cause of the truck going into "Limp Mode" the Powertrain Control Module (PCM for short) must be scanned to see what fault code comes up, since the shop tha ... Chevrolet S 10
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.2572 seconds