Having problems with your 2008 GMC Envoy ?

P0449 and P0455 error code 2008 2wd gmc envoy 30,203 miles

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

P0449 - Evaporative Emission Control System Vent Valve/Solenoid Circuit Malfunction

P0455 - Evaporative Emission Control System Leak Detected (no purge flow or large leak)

Both are refer at EVAP system; other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0446 - P0453 - P0455 - P0456

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.
Causes: most likely means one or more of the following has happened:
A loose or improperly affixed gas cap
A non-conforming gas cap (i.e. not factory/original brand)
Other leak or damaged piece in EVAP system

Possible Solutions: the most common repair is to:
Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back.
Otherwise, replace the gas cap, and/or
Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary


Hope helps.
Http://www.obd-codes.com/p0455
Repair Help & Product Troubleshooting for 2008 GMC Envoy

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

P0449 and P0455 error code 2008 2wd gmc envoy 30,203 miles


P0449 - Evaporative Emission Control System Vent Valve/Solenoid Circuit MalfunctionP0455 - Evaporative Emission Control System Leak Detected (no purge flow or large leak)Both are refer at EVAP system; oth ... 2008 GMC Envoy

I Have a 2000 gmc safari van 2wd The fuel pump stopped working so I replaced it. now cylinder 1 and 3 and not firing. So I looked at the plugs and they look good. I changed the wires but still no 1 and 3 firing. I get and p0135 error code (No 1 Ox sens) but that should not stop the plugs from firing. Could a vaccumm leak cause this or what? Thank you, Steven


The P0135 is indicating an O2 heater problem which is separate from your miss-fire problem.\015\012I would ask the obvious, are the #1 and 3 injector harnesses connected to the injectors? Have you check for a pulse at the suspect i ... 2000 GMC Safari

I have a 2004 GMC Envoy 2WD 6 cylinder 4.2 liter engine The car has 150,000 miles and we were told that rear heater leaks and it will cost for the replacement part $1,240.00. Is there a way to repair this for much cheaper.The smell is like antifreeze so we have to do something.The dealer offered to reroute so that heat would come in the front only. There's got to be a better way.Thanks


If you are handy you may be able to take out the rear heater core and take it to a radiator shop to test and repair the leak,,,other than that you can probably find a used one for alot less ,last you can do what the dealer suggested,just block off th ... 2004 GMC Envoy

Getting a lean burn error code on banks 1 & 2. reset it and drove 250 miles before it came back on. Reset it again but the code came back within 10 miles. Checked for vacuum leaks, none found, replaced the MAF sensor but code came back within 10 miles.


Check for vacuum leaks.Air tube between air filter and intake manifold.If the motor has over 80,000 miles then the intake manifold gasket can **** in air and leaning out the air/fuel mixture.Give each air / vacuum ... 2001 Cadillac DeVille

I have a 2004 gmc envoy . I put the code reader on and it said code 301 . The car is running really heavy and stuttering . I changed the sprk plugs . But then I erased the code by accident . I changed my number 1 and 2 coil to see if the number 1 coil is bad . If it was would my check engine light or would the code come back up if it was bad ? Because I changed them and my check engine light didn't come back on


Keep an eye on the coil that was originally on your #1 plug. If it was bad you would get a code again, but I suspect it was a "contact" or connection issue & moving it made better contact on the cylinder you moved it to. ... 2004 GMC Envoy

My 1998 volvo V70 XC had two eng light codes: 1) P0442 evap leak small and 2) P0455 evap leak large. I replaced the fuel tank gas cap for a new one and reset the codes with OBDII. After I drove 100 miles a code P0455 evap leak large turned on. I'm not sure what to look first, charcoal canister, any fuel lines on top of gas tank. Please help. thanks


A 0.040 leak has been detected in the \015\012\011\011\011\011\011evaporative system. (A faulty gas cap may cause this code). \015\012\011\011\011\011\011Also see\015\012\011\011\011\011\011 ... 1998 Volvo V70

05 kia rio, just rebuilt, get 325 knock sensor error code and 301 #1 misfire code. Timing marks on cams and crank are aligned, new NGK plugs gapped at 0.04 in, new plug wires, appears with good spark, new knock sensor in. Runs great, good power, maybe just a little rough at idle. Does code 325 mean I have a knock problem or that there's a problem in the knock sensing system. Also there appears to be some dark residue on top of the pistons. There is 200 miles on rebuild at this point. Error light


P0301 Is a misfire on # one cylinder and P0325 is a knock sensor code . The knock sensor has a lot to do with spark advance . The so called knock is a spark knock from the plug fireing . If i were you at this point i would check the crankshaft pisiti ... Kia Rio

My 2003 gmc envoy has p0303 error code. I have since changed the plugs but the code is still there. What else should I look at before changing the expensive coil on cylinder 3?


To find out if it is the coil pack, swap #3 pack with another cylinder and see if the fault changes. If not, you should check the compression on cylinder #3. If that is OK, I would suspect a bad injector. ... 2003 GMC Envoy

I have a 1999 Ford Ranger 2.5L 2WD. The check engine light is on and displaying 5 codes when I scan it. P1506 (IAC overspeed error), P0135 (O2 bank 1 sensor 1), P1451 (Evap), P0141 (O2 bank 1 sensor


... 1999 Ford Ranger SuperCab

I have a 2002 toyota celica gts, and just recently the check engine light came on. I had my friend read the code, and it came up as 301, misfire in cylinder 1. To try and diagnose the problem, I switched coil #1, with coil #4 to see if the problem follows. About a week later, the light comes on again, the same error code 301. The next step I took was to replace the spark plugs, my car has 81k miles on it at this time. And yet again, a few days later the check engine light comes on again. N


Rotate the wires swap #1 with the "bad" one if you can, before you spend money on a new set of wires. This problem usually is caused by: either a broken sparkplug carbon wire coreor, a mis-alined reluctor. ... 2002 Toyota Celica

2007 GMC Envoy p2440 bank 1 code - 2009 GMC Envoy


... 2009 GMC Envoy

I have a 89 Chevy Suburban 2500HD 2wd, with a 350cid TBI, TH400 3spd trans. Everything is new or rebuilt (major overhaul six months ago) it has started displaying a check engine light after 2 miles or once it reaches temp (200F). Using a code reader to find out what the error is results in "no error code stored in computer memory". I've had GM dealerships try to read it as well with no luck. The ECM & Prom was replaced with a new unit to try and resolve this but I still have the same problem. An


Intermitten problem, as vehicle is running the computer is continuely recording, while the error is happening the code is registered. After the problem is not happening the computer records new information and does not maintain the old. Fix, find a ... 1989 Chevrolet Suburban

Gmc envoy error code 606 - 2004 GMC Envoy


... 2004 GMC Envoy

03 gmc envoy with 5.3 140000 miles. Oil pressure reading fluxuates between 0 and 40. When problem first started pressure read 80. When vehicle was new it stayed at midpoint (40) vehicle has plenty of oil. if you rev engine or increase rpms it goes to 0 and stayes there. let off and it jumps around like it did when started (0 to 40). No engine pecks while running. Display indicates low oil pressure and stop engine. orange light (check gages) comes on when at 0. any ideas. Service engine has not c


There may be a loose wire or the gauge or sending unit may be going bad. The first thing I would do is to hook up a temporary oil pressure gauge, not using the old one at all. With this watch gauge while driving and see what readings you get. If the ... 2003 GMC Envoy Xl

Gmc envoy check engine codes 0440, 0455, 0442 cleared codes after gas cap replaced, lite came back on after about 300 miles


... 2003 GMC Envoy

2008 6.2L gmc yukon error code p0449 - Yukon Denali GMC Cars & Trucks


... GMC Yukon Denali

2006 gmc envoy denali 5.3, no oil leaks, 61000 miles, steady vacuum gauge reading at 16, runs and starts very good. Takes 1 quart of oil per 1300 to 1500 miles, no exhaust smoking. Why so much oil ?


Google search GM 5.3 oil consumption. This is a known and common issue. ... 2006 GMC Envoy Denali

2006 gmc envoy denali 5.3, no oil leaks, 61000 miles, steady vacuum gauge reading at 16, runs and starts very good. Takes 1 quart of oil per 1300 to 1500 miles, no exhaust smoking. Why so much oil ?


... GMC Yukon Denali

Error Code reading bank 1 sensor 1 keeps coming on. I had the oxygen sensor replaced but the light keeps coming on. My vehicle is a 2006 Chrysler Pacifica with 99,500 miles on it.


... 2006 Chrysler Pacifica

I bought a 2005 GMC envoy xl. It has 160000 miles on it. Runs great but about a week after buying it my oil pressure gauge started fluctuating from 40 to 0. It did it this one day multiple times and stopped. I brought it to the shop and the replaced the sensor. It didn't do it again and then after driving 90 miles mostly highway in 80degree weather, it started doing it again. This time it smelt like burning oil. It has not done it again and the oil level is fine. I'm bringing it back to the shop


Yes it is possible you bought a lemon. The problem could be the gauge on the dash, the wiring to the sensor, or an actual problem with the oil pressure. A mechanic will have a difficult time troubleshooting the problem if you can not duplicate it o ... Cars & Trucks

1995 3.0 2WD 4runner SR5 Long Explanation Before problem description: New short block was installed and engine was run (less than 50 miles) when knock sensor code was set and due to illness was parked and never touched/run for about 3 years. Knock sensor code was only issue in the beginning after it sat for 3 years several thing had to be done: replaced fuel pump,strainer ,filter,cleaned and flushed tank and lines, replaced knock sensor (and all necessary parts), replaced 1 injector(cracked plas


Did you do a compression test? and did you do a Vac. text at the Port hole to see if you had a steady needle? ... 1995 Toyota 4Runner

Hello, I have a 2002 GMC Envoy and my check engine light is on. The code populated is P0014, I've read different solutions to this code, however I am still unsure as to which route to go. Would the replacing the Camshaft sensor resolve my issue? Also, when my AC is on the timing appears to go up and down (from 0-2), as if my truck wants to shut off, and then Pressure Oil Low // Stop engine displays. Thank you for any assistance you can provide.


DTC P0014 - "B" Camshaft Position - Timing Over-Advanced or System \015\012Performance \015\012 (Bank 1) = to see Trouble Code P0011DTC P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)What ... 2002 GMC Envoy

How do you fix a 2008 gmc with an error code of p0455


... 2008 GMC Sierra 1500

Sat, sometime in January cel appeared Sun Engine steaming, upper hose clamp on engin was loose at engine connection cyl 1,3 side tightened clamp, washed away antifreze Mon read codes, engine misfire cyl 1,3 assumed something to do with antifreeze leak, cleared codes. 60 miles cel, same codes, replaced sparkplugs, swapped cyl 1,2 wires, cleared codes. 60 miles cel, replaced coil pack, air filter, ysed can of injector cleaner, cleared codes, 160 miles cel, used another can of injector cleaner. 160


I am sorry to tell you this but sure sounds like a head gasket getting weak. By year a model I am figuring you have a EJ-25 2.5 boxer motor. Not easy to really do plug test but are your plugs coming out with moisture on them? Check oil for water also ... 1998 Subaru Forester

1st error: p0136 oxygen sensor circuit bank 1 sensor 2 2nd error: is p0325 knock sensor 1 circuit (bank 1) my check engine light came on with and I went to advance auto parts store and they checked the code for me with their code scanner the 2 error codes were read. how much will it cost to get them fixed at the dealer? I don't have the mechanical skills for this problem.


Around 300.00 -400.00 est. at dealer garage maybe little cheaper not much more ... 1997 Nissan Maxima
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.0761 seconds