Having problems with your 2008 Dodge Avenger ?

P2017 intake manifold runner positon sensor or switch circuit high bank 1

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2008 Dodge Avenger

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

P2017 intake manifold runner positon sensor or switch circuit high bank 1


... 2008 Dodge Avenger

Code p2017 intake manifold runner pos. sensor bank 1 circuit high how to fix this problems


... 2007 Chrysler Sebring 2.4

2008 Jeep Patriot. Check engine light on. Code p2017 Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1? What is that and how do I fix it?


... Cars & Trucks

Random/multiple cylinder misfire detected Bank 1 too lean Bank 2 too lean Differencial pressure feedback EGR circuit high input intake manifold runner control stuck open Spark plugs? Vacuum hose(s)? EGR cleaning? From what I've seen it's not a hard fix.


Hiit sounds like the EGR valve is either dirty or has failed, do you lose any power at all, if not then thats a good sign, remove the EGR and clean with carb clneaer only, leave to dry naturally and dont try to dry it or touch it yourself ... 2001 Ford Windstar

Pliz help after taking my car for engine wash they used water to wash the engine and engine Codes came up . 16502 P0118 Engine coolant temperature circuit-G62:high . 16497 P0113 Intake air temperature sensor 1 circuit-G42:high. 16486 P0102 Mass air flow circuit -G7 0:low input. 16622 P0238 Turbo super charger boost sensor (A) circuit : high. 16955 P0571 Brake switch sporadic (A) circuit : malfunction. 18000 P1592 Altitude sensor /boost pressure sensor :implausible ratio. 16706 Engine RPM sens


Not Good: The Expensive main computer brain sustained a short from either the heat of the solutions or leakage allowing fluids to enter the components. If after a drying period this still occurs; then the computer brain needs replacing. ... 2005 Volkswagen Touran 1.6

My 99 Volvo s80 t6 is reading a bunch of codes p0118, engine coolant temp sensor circuit high input.p0238, turbo/ super charger, boost sensor A circuit high.p0236, turbo/ supercharger boost sensor a circuit range performance.p0050 Ho2s heated, o2 sensor / control circuit bank 2 sensor 1. And p0114,(iat) intake air temp sensor circuit high temp. I hear that the transmission control module could be causing all these problems? I really dnt know thought any ideas please help!!!!


... Cars & Trucks

On 2007 chrysler sebring 2.4 L eng. where does intake manifold runner position sensor located & manifold flow valve ?


... Chrysler Cars & Trucks

What does intake manifold runner position sensor circuit high mean on a 2008 dodge advenger


... Cars & Trucks

Want to repair DTC code P1512 and P0031 P1512 is 2000 Mazda MPV van intake manifold runner control stuck closed and P0031-H02S heater control circuit low bank 1 sensor 1. If I can repair it myself, just need to know how and where the location in the engine compartment


... 2000 Mazda MPV

I had replaced my 4 o2 sensor on my suv after used OBD to reset the board to turn off my checke eng. light came back on. I replaced o2 sensor by universal type of o2 sensor.I got this message on the OBD: 1)p22392 o2 sensor positive current control circuit high bank 1 sensor 1. 2)p2242 o2 sensor positive current control circuit high bank 2 sensor 1. 3) p2252 o2 sensor negative current control circuit low bank 1 sensor 1. 4)p2255 o2 sensor negative current control circuit low bank 2 sensor 1


... 2003 Toyota 4Runner

I own a 1996 Jeep Grand Cherokee and I am having idle problems. The tach goes up and down and then dies when I come to a stop every other stop. I put it on a computer and it read the following P0108- manifold absolute pressure/barometric pressure, circuit high input and P0113- Intake air temp circuit High input. What should I fix, I'm thinking the MAP sensor or mabye something simple as a gasket, but I could be very wrong. I need a pro's help. Thank you in advance, Andrew


Hi, first check for a clogged PCV valve. This can cause your idle air control valve to act up. The pcv valve is shoved in to the valve cover with a hose on it that leads to the intake manifold. If the PCV flow is good, check for vacuum leaks on an ... 1996 Jeep Grand Cherokee

I own a 1996 Jeep Grand Cherokee and I am having idle problems. The tach goes up and down and then dies when I come to a stop every other stop. I put it on a computer and it read the following P0108- manifold absolute pressure/barometric pressure, circuit high input and P0113- Intake air temp circuit High input. What should I fix, I'm thinking the MAP sensor or mabye something simple as a gasket, but I could be very wrong. I need a pro's help. Thank you in advance, Andrew


Do you have the air filter in place? The removal of the air filter will cause this same issue. If it is not the filter, then the mass air flow sensor could be going out. ... 1996 Jeep Grand Cherokee

1996 4 runner had p0171 repair o2 sensor and exhaust leak rd test mil light came on p0325,p0330.knock sensor codes circuit codes banks 1,and 2.replace knock sensor harness under manifold sensor visual look ok.ohm harness to ecm no opens,or shorts to ground or power.was told after market wires could cause these codes?


What is the resistance of the wires between sensor and ecm connector, excess resistance from varying gauge wire and solder or solder-less connections can cause problems ... 1994 Toyota 4Runner

2003 Beetle turbo-13 trouble codes-PO300-multiple cyl misfire-PO171-system lean, bank one, PO301, PO303, PO302,PO 304-cyl one thru four misfire, P0012-intake cam position timing over-retarded-bank one, PO333-knock sensor curcuit high input-bank #2, PO328-knock sensor 1 bank one-curcuit high input, PO721-output speed sensor curcuit range/performance, PO731, PO734, PO 729 all trans incorrect gear ratio codes. Unit runs but exhausts back into the intake after 10-15 seconds after start up. All this


Low fuel pressure will cause many of those codes to set.Should have around 3.5bar pressure at idle and full throttle.Check to see if VW has a recall on the ignition coils. They are cheap to replace however.....you will need yo ... 2002 Volkswagen Beetle Turbo S

Error codes, P0127 Intake air temp too high and P0328 Knock sensor 1 Circuit high input bank 1? What do I need to change to fix these system problems?


Here you go John:\015\012\015\012http://www.nissanhelp.com/diy/obd_codes/p0127.htm\015\012\015\012 ... 2002 Nissan Xterra

Intake manifold runner position sensor


... 2008 Dodge Caliber

Where is this? intake manifold runner position sensor


... 2008 Dodge Caliber

Position sensor swith circuit high bank 1


... 2007 Toyota Camry

Intake manifold runner position sensor?!!


... 2005 Audi A4

I have a 2007 dodge sprinter van 3500 diseal says intake manifold runner sensor bank one


... 2007 Dodge Sprinter Van

What is the price for intake manifold runner position sensor , p2016 &p2017


... Cars & Trucks

P2008 Intake Manifold runner control circuit/open (Bank 1) Engine light comes on if you drive at 130km/h then it loses power and drives at maximum 100km/h until you switch off ignition and then its fine again. This is actually on a Toyota Hilux D 4D, 1KD engine.


Hi.P2008 means intake runner control circut/open bank 1. The intake mainfold running solenoid must be checked and eventually replaced. The solenoid is located off the vacuum hose and operates the intake runner shaft throught the mainfold. ... Toyota Tundra

Intake manifold runner position bank 1 circuit hight check engin light comes on


... 2007 Chrysler Sebring Sedan

2001 hyundai accent o2 sensor heater circuit problem bank 1 sensor 2 and the camshaft position sensor circuit high input bank 1 or siigle sensor. (PO141) and (PO343) will these stop the car from running or starting, and is the O2 sensor a upstream or downstream ????


Yes the cam shaft error code will stop the car from fireing as it does not know what position the camshaft/pistions are in. The O2 should not but may be a resulting code of the camshaft sensor code. The o2 sensor is downstream in the exhaust system. ... 2001 Hyundai Accent

I have a 1996 lexus es300 that failed emissions with the following codes: P0100: Mass or volume air flow circuit; P0110:intake air temperature circuit P0135 02 sensor heater circuit (bank 1 sensor1) P0330 knock sensor 2 circuit (bank 2) i need to know what exactly the part# to find on line... should i go to the dealer and then parts store?


What was the first code present. that one code will chain react the rest .clear them let them come back on and they will then compare the order ... 1996 Lexus ES 300
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.9038 seconds