Having problems with your 2007 Volkswagen Passat Sedan ?

I have problem truble code by vas 08518 : fuel injector group asupply voltage

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Try Google; you'll be suprised what you find.
Repair Help & Product Troubleshooting for 2007 Volkswagen Passat Sedan

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have problem truble code by vas 08518 : fuel injector group asupply voltage


Try Google; you'll be suprised what you find. ... 2007 Volkswagen Passat Sedan

2006 1 ton sprinter, problem is just quits running, not all the time, will restart and may be good for a week or more, Code says p2146 which is fuel injector group A voltage circuit open ..... what will fix this???


... Dodge Sprinter

2000 ford f150 160,000 miles. Had to replace fuel injector #2 cylinder 3 years ago. Recently, started getting rough idle and obvious misfire. Check engine light (cel) code 0302. Put in new plugs, wires and coil pack. CEL off and no misfire or rough idle. How do you know if this soved the problem or an injector is going bad. Too hard for a DIY to change fuel injector. #2 problem. Seat belt giving 27 code. Can't locate problem #3 problem! Odometer comes on and off at will. S


... Ford F-150

Code P2146 Fuel Injector Group A Supply Voltage Circuit / Open


... 2006 Dodge Ram 3500 Truck

My 91 chevy corvett fuel pump want come on untill the oil pressure turns it on.I checked the fuel pump relay and it checks ok Ireplaced it anyway. i just finished replacing all of the fuel injectors in it and then this problem shows u. The brain shows no problem codes stored in it either. the problem with the injectors turn out to be a shorted injector but as i said I replaced them all. the car only has 33k orignal miles on it.Thanks need help in alabama


... 1991 Chevrolet Corvette

Main Problem: code reader scanner unable to connect to vehical computer. Vehical is also not starting has some issue with fuel delivery I believe. Motor turns over, has spark, I do not hear fuel pump going on the key turn (installed new one also). Was told by cert. GM tech that the grounds for the ECM could cause code reading errors and fuel delivery problems as the fuel injectors will not fire with ground ecm problems. QUESTION: All ground locations for the ECM. I was told there is one on the


Well, I don't know about the "cert.GM tech", but the WIRING DIAGRAMS for your vehicle say that there are 4 ground circuits for your Powertrain Control Module (PCM) They are pins 16, 56, 57, and 60 in connector 1 at the PCM. They all have the same gr ... 1998 Oldsmobile Silhouette

2007 Ram 2500 with 6.7L Cummins 23K miles. Ran rough. Error code 205 and 307. After driving for a day the truck would run just fine and error codes would go away. If truck sits for a week same problem re-occures. Took it to the shop, they replace all the injectors. Truck ran fine for about three miles then rough running and error codes came back. Already Tried: Fuel additive, Replace all injector,New 2-micron fuel filter and FUel pump


PCM ... 2008 Dodge Ram 2500

I have got a 98 Cadillac deville Sts engine light on, T.S.C(trouble shooting Code)P0 202, P0203, P0205. P0208, P0202 P, P0203, P0205, P0(Open fuel Injector Circuit 202, 203, 205, 208) Brand New Fuel Injector(Brand New)Oxygen Sensor and still has these codes how do i solve the open injector fuel problem on these 4 cylinders please help !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! please email me at this address ([email protected])


... 1998 Cadillac DeVille

My 98 isuzu trooper check engine light is on. i got it checked and the code reader read that its the fuel injector. i took it to a shop and they went to change the bad fuel injector and when they went in they said that its not the injector causing the problem. they said that something was causing the injector to send off the signal. whatever it is it has my trooper sounding like a diesel truck. do anyone have a clue of what could be causing the problem?


... 1998 Isuzu Trooper

2001 subaru forester fuel delivery problem. Checked the codes with a snapon scantool and found a low cat code very common. Looked at O2 sensors and saw one reading barely out of range replaced it. Noticed old o2 sensor was white. Did not fix problem, look at spark plugs found cylinder 3 to have a white plug as well. Check injector seemed to have no flow issues. switch injector 1 and 3 to be sure. Still have same problem car stumbles from a stop and sometimes climbing hills.


White sparkplug indicates coolant in the combustion chamber, ... Cars & Trucks

I have a 1988 Porsche 911 3.2 which is not starting. I have narrowed down the problem to fuel. If I put some fuel in the inlet manifold the car starts. It appears the injectors are not working (no sound from injectors when cranking and voltage only 6v when it should be 10v, also no pulsing)....is this a problem with the DME ? Any ideas ?


Hi Protein,Your best course of action would be to have a scan carried out. I believe the problem is either to do with the crank or cam shaft sensors.Regards Johngee10 ... 1988 Porsche 911

Hello there, i have a 2000 impala 3.8 v6 series2 engine and the code p0300 keeps showing up on the code scanner...i replaced the plugs, wires, intake manifold and gasket for it, tubings/vacuum lines checked all sensorson the throttle body, replaced egr gasket, coil packs,fuel filter,fuel pump is still good,and the hose and pcv valve was also good wat else could be the problem?? i replaced the o-rings on injectors but not the injector wasnt checked.. i haven checked because i spent enough cash on


The error code Stands for: random/multiple cylinder misfire detected. sounds like you just forgot to reset the error code once you repaired the issue.... hmmm, A P0300 OBD code indicates a random or multiple misfire. If the last \015\012 ... Chevrolet Impala

1992 Chevy S10 blazer 4wd (4.3 TBI engine code Z). One of two injectors shuts down and the vehicle stalls (left injector while looking into the engine compartment from the front of the vehicle). I replaced the fuel filter to ensure there was not fuel restriction. I also replaced the injector and the vehicle ran for about 15 minutes before the problem returned. When the engine is cold and I first start it, sometimes both injectors will run, but within 30 seconds of starting the left injector will


Replace ECM ... 2002 Chevrolet S-10

Error codes P0301(cylinder #1 misfire) and P0304(cylinder #4 misfire). Originally thought there was a failed ignition coil that controls cylinders #1&4. After putting new coil in, problem still present. Tested further and found there was no fuel coming out of cylinder #1 fuel injector. Tested injector and found proper power at injector but it wasn't duty cycling on the ground side. Ohmed harness from injector to ECM and found within spec. Back probed connector for all four injectors and found n


The ECM is very possible.I assume cylinder 4 injector is providing gas?The connection for cylinder 1 is probably a connector with pins correct?If you can bypass the ECM,that would get you closer if not give the answer.I would try using a wire straigh ... 1998 Toyota RAV4

2004 Dodge 3500 Cummins, Truck was harder to start for the past week but ran fine. Went to work without a problem, when I went out to go home crank but no start. Not so much as a pop or sputter. Exhaust has no raw fuel smell, new fuel filter, 1/2 tank of fuel, cracked fuel lines at the injectors and had plenty of pressure and flow, checked lift pump for pressure output and was well within factory specs. No codes stored. Bled the lines again and it started. Drove home no problems, next morni


Well I'm leaning towards a battery problem,, try a battery from anoter vehicle and see if it still starts hard..The sensors have to be tested with a diagnostic tool,, eighter obd 1 or obd 2 tester.. Its connected to the cars computer and ... 2004 Dodge Ram 3500 Truck

I have 97 blazer with 4.3.had a deadshort to 5v reference wire that controls tps, air temp sensor circuit short was located a fuel level buffer module. relaced circuit board ....this resolved the low or no voltage issue. the problem now is that the car will crank, has spark and fuel but will not fire. i have replaced fuel pump, fuel pressure regulator and tested for voltage pulses at injectors.... any thoughts


Just a thought pull a coulpe of spark plugs see if there flooded also if you can scan the veh look at tps voltage now and look for cranking rpms should be around 240 rpms ... 1989 Chevrolet S-10 Blazer

2004 Dodge 3500 Cummins, Truck was harder to start for the past week but ran fine. Went to work without a problem, when I went out to go home crank but no start. Not so much as a pop or sputter. Exhaust has no raw fuel smell, new fuel filter, 1/2 tank of fuel, cracked fuel lines at the injectors and had plenty of pressure and flow, checked lift pump for pressure output and was well within factory specs. No codes stored. Bled the lines again and it started. Drove home no problems, next morni


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. First of all you’ll need to check battery voltage, recharge it\015\012if it is low or jump start w ... 2004 Dodge Ram 3500 Truck

Have fuel to injectors but injectors will not spray. It has 11.9 voltage going to injectors. The truck was running about a week ago. I went over some rail road tracks and it died. Since then I have replaced throttle body and it still has same problem. no fuel spray from injectors.


Fuel pump in gas tank. ... 1988 Chevrolet S-10

Idling problems 1992 honda accord / in park car idles back and forth from 1000 to almost 3000rpms constantly, in gear it does it only sometimes. wired across the E.C.U. unit under pass. side dash, it gave me a code for throttle position sensor, so i changed out the throttle body intake(because you cant just change the sensor alone). also changed fuel filter, injector resistor,fast idle thermo valve,and IAC valve, tried checking for a code again, now i get no code, but the problem continues, i am


... 1992 Honda Accord

2002 5.3 L long cranking to start after warmed up. replaced fuel pump w/ same problem Code reader showed PO307 fuel misfire but only showed once then O-Codes. Injectors all sound funtioning. Could bad O-ring cause fuel pressure loss ?


Yes bad o-ring seal in the fuel pressure regulator could be the problem causing the loss of fuel pressure.\015\012Also bad o-rings on injectors can also cause loss of fuel pressure.Also check the FPR itself.If fuel ... 2000 GMC New Sierra 1500

Hi my problem is with a 2000 buick regal 3.8 super charged engine code 1. when the ignition is first turned on the PCM energizes the fuel pump relay and pressure is 50 psi.,when engine starts fuel pressure drops off and engine stalls,after the engine stalls fuel pressure builds back up to 50psi.there was a truble code P0230.I have checked pins and connectors at PCM ane relay's for damaged or broken terminals.Continuity test on grn.wire at pin 39 blue connector of the PCM to the connector at the


Hello! Are you using a "digital" volt meter? if not you'll need one...Connect the + probe of a volt meter to the Dark Green/White wire and the - probe to ground...turn the key to start and see if the + 12 volts from the ECM to the relay winding stays ... Buick Regal

Knocking pinging Hello, I have a 4.3 ltr engine Silverado 02 and everytime I go uphill I hear a knocking or pinging noise. I have done a ll the major tune up and still the same. I read a book and it says check the fuel injection system. So right now I am guessing it might be the fuel injectors. The OBD is flashing a code 300 and sometimes cylinder 6 code would show up. I have changed all the wires and spark plugs too, new distributor, new fuel filter, new air filter and still same problem. So th


Get your timing light out and make sure that your timing is set at O degrees. This is very important on a Vortech engine. If you had a blown head gasket the engine would have a undeniable shake. As for the piston hitting the valve, not likely unless ... 2002 Chevrolet Silverado 1500

My Grand Marquis sometimes will not start after it has been driven for a while. During the drive all indications are normal. The engine will turn over, but it will not start like there is no fuel introduced into the injectors. I've checked the injectors when the car is running and they are getting fuel and the fuel pump is functioning properly. The dealership has run a diagnostic check and found nothing. Could the chip within the key be going bad or loosing a code and cause this problem causing


Yes the key could be a problem BUT your theft light would be flashing on the dash while you are trying to startsince you have fuel during the concern I am going to assume that you are missing spark?if no spark you could be dea ... 2000 Mercury Grand Marquis

Mazda Millenia 2001 S. Engine has been misfiring since 4 months now. Changed the air filter, air filter hose (which was broken), fuel filter and got fuel injectors cleaned twice. Runs fine after getting the fuel injectors cleaned for a day or two and then the same problem back again. Check engine light has been On & OFF since then but since last 12 days it has been ON consistently and starts flashing sometimes. Got codes checked 4 months ago and it said cyl 6 misfire and now it says cyl 3


The injectors are weak/faulty.All the injectors needs to be replaced.This will solve the problem.The misfire is caused by faulty injectors.\015\012front plugs (cylinders 2,4,6) and rear plugs (1,3,5) .Replace all the cylinders.\015\012 ... 2002 Mazda Millenia

98 concorde lxi runs great but when you turn it off when it is hot then try to start it 5-10 minutes later it wont start. Turns over but won't fire, sometimes it will sputter a little. 30-45 minutes later it starts right up. it is as if it needs to cool down. It acts like fuel is not getting to the injectors. Fuel pump was already replaced. when it is cooler (ambient temp) there is never a problem. No codes are present in the PCM and under hood temp seems very hot when problem arises. I am suspe


Ignition MODULE needs replacing on the distributor ... 1998 Chrysler Concorde
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 4.3590 seconds