Having problems with your 2007 Subaru Impreza WRX STI Limited Sedan ?

Just got the motor replaced and im not getting any spark

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Check crankshaft sensor
Repair Help & Product Troubleshooting for 2007 Subaru Impreza WRX STI Limited Sedan

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The motor is turning over but not firing up. I removed a spark plug wire to see if it was getting spark, nothing. I then replaced the wire n removed the wire running to the coil, then i got sparks. I removed the spark plugs n noticed they were full of gas (drenched). I let them dry, but think im going to replace them. I then removed the distributor cap. rotor looks worn n burned but my question is... If im getting sparks at the distributor cap why isnt it sending it to the spark plugs? co


Replace rotor button ... Chevrolet Astro

No spark EB '93 Ford Fairmont. The motor was idling and it stopped. I've replaced the coil, checked the fuses, replaced the relay and checked for spark. I was going to try direct power with a fuse in the line to the coil, but I don't really want that to happen. I'm still getting no power going through the coil. It has been suggested to replace the distributor. To me that seems rediculous because you've got to have power going through the coil first don't you? What else could it be? Maybe it coul


Your distributor sends trigger signal for coil, based on cam and crank position sensors test distributor output and sensors you can get info on troubleshooting from repair manual (purchase from parts store) under troubleshooting section in manual. Yo ... Ford Fairmont

Driveing and truck stoped running,,replaced fuelpump and filter,,got a bad pump and replaced it again,,truck would still not start so I checked spark,,,had a bad cap due to ear on desterbitor broken,,replaced desterbitor,cap,rotor and mod. anlong with plugs and wires.. Truck is still not getting spark all the time... 98 GMC Sonoma 4x4 4.3 (w) motor... ran out of things I can think of that could be wrong... any suggestions on what to check ?


Check to see if you're getting spark from coil into distrubitor. if you replaced al those, the only thing i can think is it's the coil. ... 1998 GMC Sonoma

Got the car in pieces and was told the timing belt was replaced and all that was needed was to have all the accesories reinstalled. Reinstalled the pieces that were with the car and got a no start characteristic. The vehicle is getting fuel and i have good spark from the coil. Sounded to be an accelerated crank and didnt want to even try to turn over. I tore the motor back down and reset the timing myself however with aligning the timing while the marks were lined up on the camshafts and the cra


You mentioned having No. 1 cylinder on TDC; you may just have the distributor off at 180 deg. Simple error to make, No. 1 cylinder may be on top of exhaust stroke verses compression stroke. I'd check this first. Also look at your compression, if you ... 1995 Dodge Spirit

Replace the 4.7 engine with a4.7 of a2003 dodge durango and now i can]t get it to start i already replaced all the original sensors along with everyting from the old engine and i know the motor is good iheard it run in the durango it acts the timing .its got gas and a good spark but it wont start


Make sure timing belt aint broke ... 2001 Jeep Grand Cherokee

Got the car in pieces and was told the timing belt was replaced and all that was needed was to have all the accesories reinstalled. reinstalled the pieces that were with the car and got a no start characteristic. the vehicle is getting fuel and i have good spark from the coil. sounded to be an accelerated crank and didnt want to even try to turn over. I tore the motor back down and reset the timing myself however with aligning the timing while the marks were lined up on the camshafts and the cra


With the nimber one cylinder @ tdc on compression stroke and all timing marks lined up dist. installed with rotor button pointing towards #1 you should be okay this is not an interference engine meaning if timing is not lined up properly the pistons ... 1995 Dodge Spirit

Got a 98 eagle talon 2.0 non getting no spark just replaced it used motor tho any help ??????


... Cars & Trucks

Just got the motor replaced and im not getting any spark


Check crankshaft sensor ... 2007 Subaru Impreza WRX STI Limited Sedan

I have a 2001 ford escort I was having some problems with being able to pick up speed and sometime when the car was hot and I came to a complete stop with will die and not start for a while. we started with a tune up replace all spark plugs and spark plug wires. I went to get on the freeway two days after and after getting to about 40 mph it started to hesitate agian and by the time i got to the side of freeway would not start so we replace the coil and the spark plugs just in case they went bad


You are running out of possibilities....check all vacuum lines....then check fuel pressure. Fuel pump efficiency may be low. \012After that, a diagnostics check....maybe computer failure.\012Good luck, Paul ... Ford Escort

I have a 1996 Ford Taurus with a 98 DOHC 24 valve engine as a replacement for the original. The other day my friend borrowed it and drove to his house, got out, his wife got in. Put it in reverse backed out and it died on him. I am getting fuel and air. I am getting no spark. I have changed the coil pack and the Crank Position Sensor and still no spark. I am not getting any to the coil pack either. We have checked all fuses and relays. Any suggestions?


Check in your trunk on left ( drivers side) see if emergancy shut down has been triped. it is a red button just push it in If this was helpful please leave good feed back ... 1997 Ford Taurus

I have a 1991 Acura Integra and it turns over but it will not start. Usually when this happens its because its either not getting spark, or not getting fuel. I'm pretty sure I got spark so I replaced the fuel pressure regulator because its easy. I got a start and idle out of it, but wouldn't start again after that. Possibly a relay? Possibly the fuel pump? If it is the pump, do I have to drop the entire tank to get to that? Any more simple things I could check before going into that? I don't kno


Go to the nearest parts house and get you the main efi relay and the problem will go away.It's under the driver side dash .It's kinda hard to get to but trust me when you turn the key on that relay is not cutting the fuel pump on .Be good as new hope ... 1991 Acura Integra Hatchback

I am trying to start my 1980 gm 350 in my boat. engine will turn and have new fuel and filters. Pulled off coil wire and got spark, grounded a spark plug to the manifold and got spark. What could it be? Firing order is correct, motor just rebuilt. Carburator is a 4 barrel Q-jet. Seems like it may be getting too much fuel. Can dump gas down intake and get it to sputter. Timing is done correctly as i double checked that. 12.78 volts at the coil to an electronic dist. Tuns over plenty fast enough.


Definitely a fuel issue. be sure to check that the distributor isnt 180 degrees off. you say it'll start when you pour some fuel into the carb, it sounds like you arent getting enough fuel then. try adjusting the float level higher so that more fuel ... 1983 Chevrolet K1500

I just got done changing a 460 motor out of 1992 F-250. The old motor still ran when i took it out. But can't get the new motor to start. It seems like its not getting a strong enough spark but it is getting one and it has fuel.. I can't figure it out so any help would be appeciated. I think it might be something to do with the TFI-IV ignition system. But everything is off of the old motor and it all work fine before. Need help diagnosing the problem


Is the timing correct. go back to basic number 1 cly TDC check rotor button position add some fuel or starting fluid to prove it is electrical ... Cars & Trucks

95 goe tracker not getting fuel to motor i got the relay for fuel pump they say its under the dash on drivers side its round cant find any under the dash there all square where does it go?The motor got water but drained every thing it has spark but doesnt get gas any other sugestions?


The relay is most likely located in the engine compartment fuse box, check on both sides of vehicle in engine compartment when you find it take cover off flip over there should be a diagram, locate relay and replace. Hope this helps. ... 1995 Geo Tracker

Started fine warmed up and put in gear went reverse when shifted into drive went a few feet very few and motor stalled out and would not start again turns over fine but will not fire - problems with cap and rotor before so replaced it--no luck - replaced spark plugs because they needed it anyway-- motor is getting spark and can hear fuel pump humming-- any ideas


Spray just a little starter fluid in the intake, if it fires and then stalles you have low fuel pressure ... 2001 GMC Jimmy

I've got a micro bus with a 1800 jetta mark 2 motor convertion .My problem is that i do not get any spark to my distibutor .When i start my micro bus all it does is swing but does not start .I've put in a new coil and new modulater (tp900b).I've got power on my coil and my modulater works because i had it plugged into a other micro bus .Is there any advise on how to get the spark at the distributor because it started before.


Um u would have to change the ECU. if the tone wheels for the cam or crank pulse width are not programmed to the PCM it will not deliver spark. See if you can get what is called a PCM intersepter and have a tune shop program it for u. It seem more ... 1995 Audi S6

I just did a motor swap on my 2000 v10 excursion. I have no spark. I have replaced the crank and cam position sensor. All 10 spark plugs and tried swapping some of the coil packs from my old motor . The old motor ran but had a knock. Still not getting any spark ? Any thoughts ??


Hi, you need to check if the gap between the sensor and the crank and cam. If the gap is to big you car will not have spark. ... Cars & Trucks

Been having a problem starting my 1991 mercury capri, not getting spark out of coil, have replaced a couple time the complete distrib, which has the ignition control module on it replaced the computer, replaced the coil 3 times, when i put on the last distributor, i got it started it lasted about oh 5 minutes, couldn't get it started again, Until i took off the battery cable the car sat for oh half hr, the started again, lasted three minutes or so replace the computer with the orginal the next


When you bought the distributor, did it come with a Stator or did you reuse the old one? Also, there is some special Heat Sink compound that has to go on the flat-side of the Module before you attach it to the Distributor. ... 1991 Mercury Capri

2000 GMC Jimmy SLE 4D, 4WD - 2 problems: 1) Sunroof had been stuck ope - got it closed - dealer says that the relay in motor is shot - can i replace relay or need to replace whole motor? Where do I get these? 2) Water leaks in thru driver's window (no rain guards) - has corroded the mirror circuit board - need to replace it, but can't find one...ideas? We can do the repairs ourselves, as hubby is an ex-army mech and is awesome with fixing the vehicles - but cannot seem to find either of these...


... 1999 GMC Jimmy

I have 02 pontiac grand am and it wont start, it cranks over and getting spark and getting fuel, I replaced crank sensor, however i pulled spark plugs and didnt smell gas in the cylinders when someone else was cranking it with the key. not sure if fuel rail is bad or if the computer isnt letting the fuel into cylinders. the fuel rail is getting fuel cause i checked the release pressure valve like on a tire which is located on front side of motor. what is my problem?


Attempt to start the car by turning the key to the Start/Run Position. Observe that the vehicle fails to start and that the security light is illuminated. leave the key in the 'ON/Accessory' Position. (DO NOT turn key to the 'off' position.) ... 2002 Pontiac Grand Am

Pasenger side power window mechanism cables got stuck and jamed in power window motor spool. The cables are kinked and twisted and the spool is gouged up. The motor works OK. The window is fine. Who do I contact to get replacements for the 2 cables and the spool? Do i have to replace the entire motor?


1) any GM dealer can get the parts for you, they are not available after market.\015\0122) yes you have to change the whole works ... 1999 Chevrolet Silverado 1500

I rebuilt a Z24 motor and had a shop assemble the long block. I installed all brand new parts, oil pump, water pump, cap and rotor, spark plugs, wires, clutch, headers and a cam which was regrinded by Schneider, I'm having problems with the timing. I can't get the motor to idle. I used the stock carb and got it to idle but once you press the gas, the truck won't idle again. I drove it but only went 65mph. I changed the carb to a 32/36 and still can't get it to idle. Mind you this motor was opera


Since you put a different cam in it youll have to find the deg. that it times on ... 1984 Nissan Pickup

Just got tune up/major service on the 2001 expedition and was running great 2 days ago. Now it seems to be sputtering and the check engine light came on. It seems like it is having a fuel issue. I just got the EGR back press sensor replaced 2 days ago with the service. I also got new spark plugs, coil boots, fuel filter. I did not get the evap sensor replaced, could this be the problem. Please help. Thanks Joseph


5.4L or 4.6L engine?? Check your coils. Go to autozone or advance auto parts and have them scan the ECU for the check engine light!! Its recommended to replace all 8 COPs(ignition coil over plugs) upon replacing the sparkplugs. These typically go out ... 2001 Ford Expedition

I have a 1995 jetta that will not start. Engine turns over and cranks. It is not getting any spark at coil or plugs. Checked wires that connect to coil and it got voltage but doesn't get signal voltage to put out spark. I have already replaced coil, battery, plug wires, rotor cap, checked fuses and relays, all good.


This sounds like a bad crank position sensor. The crankshaft position sensor on the AAA engine is located on the "intake" side of the engine block, near the flywheel. Pull that sensor out and see if Auto Zone has a test procedure for it. There is ... 1995 Volkswagen Jetta

The heat in my 2006 grand prix will not get hot. We replaced the thermostat and got nothing. So I got the radiator flush and force filled again. Still nothing. Temp of the motor still gets to the middle, but no heat thru the vents. Any ideas?


Are the 2 tubes that go to the heater core getting hot? If so, then the blend door is not opening to allow heat to get to the cabin.\015\012\015\012Possible vacuum motor problem, either disconnected, or the controller for the blend door i ... 2006 Pontiac Grand Prix
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.8131 seconds