Having problems with your 2007 Hyundai Santa Fe Limited ?

How to replace a lower ball joint on a Santa fe 2007

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2007 Hyundai Santa Fe Limited

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace lower ball joint 2007 Santa FE - Santa Fe Hyundai Cars & Trucks


... Hyundai Santa Fe

How do I replace a ball joint that's going bad on the lower front right control arm. The car is a 2006 Nissan altima 4 cyl. Front wheel drive. Is it possible to replace the ball joint instead of the whole lower control arm itself? If not, how do I replace the lower control arm on a altima. Is it different from front wheel than rear wheel drive? Thanks.


To replace a ball joint with the lower control arm, use bolt breaker spray (PB blast) Remove the cotter pin and loosen hub lock nut and wheel nuts (use long breaker bar) Jack up car and remove wheels. Remove outer tie rod cotter pin and crown bolt, p ... Nissan Altima

Need to replace the lower ball joints in my 2002 Dodge Durango SXT. Receiving conflicting advise. Some say that I have to replace the whole control arm with new ball joint. Others say that I can press the old ones out of the control arm and press new ball joints with grease fittings up into it... the existing ball joints are factory and do not have grease fittings. I can't be sure, but it looks like the top of control arm that houses the ball joint is solid cast. It doesn't appear to be a "hole"


It looks like if you buy the joint from Chrysler then it comes complete with the arm however there are aftermarket companies that make just the ball joint which can be pressed in and out. It's fairly common for a manufacturer to offer the joint only ... 2002 Dodge Durango

Right lower ball joint. Torn loose from lower control arm. Ran into a sinkhole in road,wrecker driver lives next door, and saved me a few bucks on towing thank goodness. Arm is OEM. Wrecker driver neighbor says I have to replace the whole lower control arm assembly-that ball joint is not replaceable on the OEM assembly. I'm lost


If you torn the ball joint out, you very well could have more damage. \015\012If you plan on doing the work yourself, I would put the car up on stands, and take the front wheel off, and do a through examination of the whole assembly.\015 ... Mercury Grand Marquis

Replacement Front Suspension, Lower Ball Joint 2000 Ford Taurus SE ,what all has to removed to replace the lower ball joint?


The easiest way is too remove the whole knuckle and remove the joint on a bench. The Ball Joint is in the knuckle, not in the lower control arm. Try to not break pinch bolt on lower strut clamp. Hope this helps.. :-) Cobra ... 2000 Ford Taurus

How to replace the lower ball joint - 2003 Hyundai Santa Fe


... 2003 Hyundai Santa Fe

How to replace a lower ball joint on a Santa fe 2007


... 2007 Hyundai Santa Fe Limited

Replacing lower ball joint on 2003 hyundai santa fe fwd


... Hyundai Santa Fe

How to replace lower ball joint on 01 santa fe What is the procedure


... 2001 Hyundai Santa Fe

How to replace lower ball joints on 2002 santa fe


... 2002 Hyundai Santa Fe

2001 Sebring Sedan LX, 2.7l V-6, VIN Code U Lower balljoints: Can the front left and right lower ball joints be pressed into or out of the lower control arms on this vehicle? I'm being told by my mechanic that the entire lower control arm assemblies need to be replaced in order to repair the worn lower ball joints and that they are sold as complete units only and that there is no way to press out the lower balljoints. He hurriedly showed me a diagram in a MOOG catalogue which showed the complete


... 2001 Chrysler Sebring

In replacing lower ball joint on 2001 Ford F150 2wd pickup----When the new lower ball joint has been pressed in I am having a problem getting the knuckle up far enough to attach the nut to the threaded area on the ball joint.


... Ford F-150

Continuation of 1998 Plymouth Breeze Stiff Steering Issue Well, we ended up replacing basically all of the front end of this 1998 Plymouth Breeze because it was totally worn out. We replaced the front motor mount, the rear motor mount, upper ball joints, front struts, both CV axles, both control arms (lower ball joints), the Rack & Pinion and Tie Rod ends We even replaced the water pump and timing belt because the water pump was leaking and since we had it open, we replaced the timing


First, the mechanic has no idea what that switch is most likely. I have several Rack and Pinions for dodge and Plymouth vehicles and none have any electrical on them however I have seen some that do and having looked at these I'm pretty sure it is a ... 1998 Plymouth Breeze

Need to replace lower front ball joints on a 99 Acura TL. My personal mechanic wants me to get the ball joints from the Acura dealer--who wants $205 each and includes some kind of arm with the ball joint. I prefer a $40 or less ball joint only from other parts sources. Which should I use?


The ones from the dealer is a ball joint and the control arm which come together with the ball joint already press in one whole piece meaning less work to do. just a simple swap in swap out. The $40 from parts stores or parts source is just a ball jo ... 1999 Acura TL

I Need new lower control arm ball joint repair.Some say replace the whole arm assembly,and some say just the ball joint itself.Which is right??Also should the upper be replaced as well while were at it?


There is really no need to replace the whole arm assembly unless it's damaged. On the other hand it is a good idea to replace the control arm bushings, and in my opinion yes do the upper also. ... Ford Ranger

Replace lower ball joints. How do you replace Lower ball jonits?


REMOVAL & INSTALLATION \012\012Raise and safely support the vehicle, allowing the front suspension to hang free. \012Remove the wheel and tire assembly. \012WARNING Be careful when w ... 1991 Cadillac DeVille

I am working on a 1995 Ford F250, 351, manual locking hubs. I started by replacing the wheel bearings, then decided to replace the axle bearing, then found out the ball joints are bad too. Now I got everything dismantled, ordered all the parts I need, and I have a HUGE problem. The lower ball joints- I cannot find a set that are big enough to fit this steering knuckle. I've tried every size from Moog, and even gave ford the vin# to try and get the correct ones, which failed. Every one I get fall


Napa----4600 GVW---MRC 10383 $29.99\015\012 ---4600 GVW---NCP 2601273 $64.99 ... 1995 Ford F250

We have a 96 ford taurus had ball joint, front assem, lower ball joints replaced & axle aaem both sides replaced after doing this my husband drived homed it all basically poped off mechanic thinks might have differant trany so I was wondering what differant tranys could bolt up to a 96 ford taurus ( U engine)


What exactly popped off? Did the mechanic state what the transmission had to do with the ball joints? ... Ford Taurus

How to replace ti lower ball joints on a 01 navigator? Can the ball joint be replaced on the upper or do I have to get the entire control arm?


Need a special press and cups and recievers to do this kind of work but yes you can replace just ball joints uppers and lowers but you can also get just control arms for uppers and lowers with ball joints in them for a little more, let me know if i ... 2001 Lincoln Navigator

The upper and lower ball joints on my 1991 lincoln towncar are worn out and I need to know how do I replace the upper and lower ball joints on my 1991 lincoln towncar


... 1991 Lincoln Town Car

I am replacing the Wheel bearing on my 2003 Mazda 6, I am wondering how the lower Ball Joints seperate, I have everything else loose and just need to be able to remove lower ball joints before taking the rest of it to my press


You need to use a ball joint popper. this way damage the rubber on the ball joint so make sure u fill it full of grease when your done or replace the ball joint ... Cars & Trucks

Diagram to change out the lower ball joints in a 97 mercury mountaineer I was told by the machanic that my lower ball joint on the left front side needs to be replaced. My truck is making a buking noise like something is lose. I am trying to do this my self so I need a diagram to help me do this job. Please help!!!


... 1997 Mercury Mountaineer

I have a 97 AWD 5.0, I have a single clunck when i back up left or right. I had a leak in my rear pinion which I fixed and I checked the universals at the same time and they fell and look fine. I also raised the front end and checked those and they seem fine too. I put a new axel on the front driver side, and I replace the lower ball joint and the upper control arm. I put a tie rod end and new shocks and hub also on the driver side. The passenger side also has new lower ball joint and control


Without knowing where the noise is coming from, you won't have much luck fixing it. If it happens when you are moving you may have to get someone to stand next to the truck and listen. ... 1997 Ford Explorer AWD

On a 04 ram 1500 w/5.7 4-door,do u have to replace the control arms when u replace upper and lower ball joints. my chilton manual says the lower is press fit in lower control arm and u need a special press and receiver tool to do it,if not can i do it myself or is this better left to the pro's, should u replace both sides od hub & bearing assemblies if 1 is bad on the front end of same truck


No it is not necessary to replace the control arms with the ball joint, unless you want to. The bottom ball joint is pressed in, the nearest auto store should have the press you need to remove the old one, and press the new one in. Usually they have ... 2004 Dodge Ram 1500

94 grand voyager how to remove lower ball joint. will i damage seal? I am replacing axle but not ball joint. I will use ball joint removal tool


That's the right way and only way to do this, just put some lube on the fork side, that will slide on the ball joint boot when removing joint. ... 2006 Hyundai Santa Fe
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.1489 seconds