Having problems with your 2006 Mazda 5 ?

How clear the codes after checking for problems with your car

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 2006 Mazda 5

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A 2006 CHEVY AVEO, LESS THAN 80 MILES AGO IT WAS RUNNING BAD AND LEAKING OIL. CHECK ENGINE LIGHT ON AND CODE P0300. THE VALVE COVER GASKET WAS LEAKING OIL INTO THE SPARK PLUG DWELLS. REPLACED THE GASKET, SPARK PLUGS AND WIRES. THE CAR RUNS GREAT. NOW THE CHECK ENGINE LIGHT IS BACK ON WITH A P0340 AND A CATALYST EFFECIANCY CODE. I CHECKED TSBS, AND CHECKED THE SENSER AND FIND NOTHING ON THE P0340 CODE. I CLEARED THE CODES AND ROAD TESTING NOW. ARE THERE ANY KNOWN PROBLEMS FOR THE CAM S


When run with a misfire, the cat will get loaded up with fuel, it takes awhile for it to burn out, and a code may set, on some occasions it ruins the converter, try clearing it and running it ... 2006 Chevrolet Aveo

What could be the problem with my car, premio 1998 d4 engine, i have to start for several times(3) for the car to start.(hard start) it has engine check code 12,which has failed to clear up even after replacing crank and oxygen sensor and also clearing the computer memory by removing battery terminal and wait for 20 min. i recently purchase Eobd/obd2 code scanner could not link with ECM, what could be the possible DTL connector, pin layout are 4,6,7,9,13,14,16. Anyone with an idea?


DTL connector is the plug is under the hood on that car i think by the driver side ... Cars & Trucks

535 AUTO TRANSMISSION HAD NEW GEARBOX FITTED CAR PULLS AWAY IN 4 GEAR GEARBOX SPECIALIST SAY PROBLEM WITH LOOM HAD LOOM CHECKED 2 DAY AND FOUND WIRES HAD RUB ON MOUNTING REPAIRD SPLIT WIRES CAR NOW COMES UP WITH CODE 33 CAN CLEAR IT PULL AWAY & CODE RETURNS AFTER 100YDS PLEASE HELP GEARBOX SPECIALIST SAYS IT WIREING & ELECTRIAN SAYS IT GEARBOX PROBLEM PLEASE HELP


Have a BMW certified mechanic check the cars computer I had a similar problem on a 528i the chip for the transmission had gone bad and bridging the chip allowed the transmission to shift properly if this is the case replace the chip. ... BMW 535

I just replaced the head gaskets on my 96 chevy camaro with the 3.8 v6. During test drive the check eng light came on I checked the code and it was a po300 multiple misfires. I checked for vaccuum leaks and other problems and found nothing. I cleared the lite and drove the car again it ran perfect. However when I took it for its smog check as it sat idling to warm up, the eng started to idle rough and the the lite came on again the tech checked it and again it was a po300 code. Any clues????


I had the same prob with my 96 3.8. The read outs were diff every time I had it put on the machine. I took the plug wires off the coil packs, held the end next to the poles, and watched for a spark, if it sparked, that coil pack was good, one of m ... Cars & Trucks

Good day, I have a 2002 Camry V6 and Engine check light is on. I have Code checked and it is P430 that indicate that I have an emission problem either with the Catalytic Converter #2,or some other issue. After this code there are others P440, 441 etc. When code is cleared the car runs fine, when code reoccur there is an issue at around 45 to 50 MPH, you have like a little hiccup like when a Tranny Solenoid hang up. Can you advise or assit?, I would appreciate any help you can provide. Regards


The P430 code is related to the Catalytic Converter (Bank 2). Replace the oxygen sensor and then you will need to have your vehicle's computer re-calibrated with a software update using a tech-stream ,mastertech, or mo ... Toyota Camry

I have a 97' Plymouth Neon, and I had it scanned for problems because the check engine light was on and it came up as the O2 sensor. I had that replaced and it is still comming up that I need a O2 senser and my car is still having the same problem.. So I was told to disconnect the batterie for a day, or clear the code and then the problem will go away, or to drive my car for 20 miles straight and then it will register that the problem has been fixed. Is this true? Have anyone else herd of this?


There is a primary and secondary sensor and someone may have changed the wrong one. disconnect the battery for 2 minutes and it will reset. if it comes back on,there is still an issue. ... 1997 Plymouth Neon

The check engine light has been on since about 6 mos. after owning the car. Dealer said there was no problem ignore it. it has been on for over 4 years, had mechanic check codes. replaced sensors but light is still on. the code for ignition control sensor is still on but sensor has been replaced. how do i clear code?


It take a scanner to erase code ... 2001 Daewoo Lanos

I have a honda crv i-vtec suv 2002 2l petrol showing code 172 , have changed the front lamda censor and the engine temp censor and car still shows code 172 and also another saying misfiring on 1,2,3 and 4. cleared codes but still comes back on. have had it checked on diagnostics no one can find the problem. recently change timing chain, guides and tensioner. car starts first time runs well at speed cuts out on idle andis using lots of fuel and sound rough. can any body help. many thanks frustrat


... 2000 Honda Passport

05 corolla, after gassing up, whether partial or full fillup, car is hard to start. will crank but runs rough before going dead. after 3-4 starts and runs fine. toyota dealer checked codes; po 171 system to lean bank 1, po 441 evap incorrect purge flow, po446 small gasleak, emission charcoal canister bad causing codes and check engine light. replaced canister and cleared codes but still have same problem


Sounds like you may have an issue with the check valve on your in tank fuel pump. When these go bad, you have to crank several time to build up enough pressure in the fuel rail for engine start. With a good check valve, the fuel pressure will not ble ... 2005 Toyota Corolla

I have a 2007 corvette a6 and a check engine light came on and it was marking the code po777, when i drive the car with the check engine light on , it only drives in the 3rd gear drive. And when i clear the code it droves normally except the transmission it sleeps from 3rd to 4th gear. does anybody else have this problem and may know what to do or how to fix it?


Code p0770 is the shift solenoid (SS) e circuit malfunction Check the following ----Wiring,---shift solenoid---- ECM ( engine control module andTCM Tranny control module ... Cars & Trucks

A week ago my 2003 CRV suddenly had the check engine light on, then stalled at stops on the way home. I took it to a Honda dealer who ran the codes. I was told the oil was low (1300 miles after the last oil change), and agreed to have the oil changed. I was told the code was cleared and to monitor the oil level. I was told if the problem is not fixed, I might need to replace the timing chain. The service paperwork says the code was P0431 When I picked up the car from the service, the c


THAT PARTICULAR CODE IS CAUSED BY A CATALYTIC CONVERTER DEFECT. YOUR OIL BEING LOW SOUNDS MORE LIKE IT COULD BUT MAY NOT POSSIBLY BE YOUR STALLING PROBLEM. IF THE CAT IS STARTING TO GET CLOGGED U WILL START TO GET STALLING MORE ON THE ACCELERATOR THE ... 2003 Honda CR-V

2001 Mitsubishi Galant GTZ. Transmission completely rebuilt. Will not shift into ( 3rd or 4th ) Mechanics have had transmission checked and it shifts like it is suppose to, when connected to a machine that they had to rent to test the transmission. He stated that the car was staying in limp mode and the codes cannot be cleared. He is now thinking the the Cars' computer is the problem. Any direction would be appreciated. Country: United States Make: Mitsubishi Model: Gala


... Mitsubishi Galant

Hi, For sometime now my car showing P1506 code. Last time mechanic cleared the throttle, but light came on in 50 miles. Now again check engine light is off. Confused whether problem is solved or its still there, idle is 1000 RPM or less, so mechanic also could not find when it overspeed, I dont know what has to be done. Car is Ford Taurus 2003, V6. Please suggest Thanks Ashok Sharma


You don't need to know\015\012\015\012You need to find a repair shop with\015\012mechanics, that know how to properly\015\012diagnose a vehicle\015\012\015\012Then you go to the shop,BEFORE you\015\012authori ... Ford Taurus

But the check engine light came on yesterday. I checked the car using a OBD scanner, and it found 3 codes for the car: P0012- Camshaft position timing over retarded bank 1 P0301- Cylinder 1 misfire detected P0327 - Knock sensor 1 circuit low bank 1 or single sensor. After I checked the codes, (I did not erase any code) the check engine light went off . I do not notice any problem in the performance or running of the car and am generally not seeing any differences like fuel smells, lea


I think your idea is wrong. A fault code indicates a problem, though, cars can be used normally, but the problem is there, need to be addressed.or you can ask the 24 hrs live technical support http://www.diyobd2.fr/service/ , they will like to help y ... 2002 Mazda Miata

The check engine light came on yesterday on my 2002 Mazda Miata LS with about 140k miles on her. I checked the car using a OBD scanner, and it found 3 codes for the car: P0012- Camshaft position timing over retarded bank 1 P0301- Cylinder 1 misfire detected P0327 - Knock sensor 1 circuit low bank 1 or single sensor. After I checked the codes, (I did not erase any code) the check engine light went off . I do not notice any problem in the performance or running of the car and am general


... Mazda Cars & Trucks

My overdrive light starts flashing as soon as I put my car in drive and the check engine light has come back on, but not when I initially start the vehicle(the overdrive light). I had some work done on my car on Thursday to the fuel injection system. Prior to that I did not have this problem, but did have other problems after I got my oil changed almost two weeks ago. Took the vehicle to O'reilly's to have them check the codes since the check engine light was on. Was told codes PO316, PO201 and


... 2003 Mazda Tribute

About two weeks ago, my check engine light came on. My boyfriend said the problem could be the oxygen sensor. We just recently had a code reading at pep boys and the code came up as p0135. I did a little research and of course, the problem is the o2 sensor. We haven't fixed the problem yet but will very soon. My only question is...every time my car is in idle it feels as if the car is about to give out or die. Will the car actually die on the road if I don't fix this problem anytime soon?


Hi and welcome to FixYa!\012\012It may and it may not. If the sensor reached it's break point it may get you on a bad time. As a first course of action I strongly suggest that you have the 02 sensor replaced as soon as possible.\012\012Ho ... Honda Civic

How clear the codes after checking for problems with your car


... 2006 Mazda 5

My 93' corolla's check engine light comes on sporadically. i used the wire method to check what the problem was and i got problem code 42. i cant find anything on this, nor does it actually explain what my car is doing if i do. my car will rev to high rpms and not catch the gear as im driving and i have to take my foot off the gas and try again, which sometimes works. i dont want to drive my car with this problem so help is much appreciated.


There are 2 different listings for a VSS for that model Corolla - one\012 for the 1.6 3 speed automatic, and another for 1.6 manual and all 1.8 \012applications. It appears to be located on the top rear side of the \012transaxle case. \012When th ... 1993 Toyota Corolla

2000 dodge stratus 2.4l Problem im having is car stays at an idle fine. once driven n goto stop at light or slow down stalls and dies. I have checked for vacuum leak, ran my computer scanner on it and only code that comes up is a egr code. this code has been present for over a year. but now stalling problem in the past month. pls helpwith any suggestions where to check for problem.


YEP!.. think about it!... EGR = Exhaust Gas Return.. .if this valve sticks open, it can causew the probolem you describe. ... 2000 Dodge Stratus

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

Check engine light comes on, car sputters, loses power, and shifting becomes irregular. Dealer mechanics say it's fuel line related (checked gas cap, all was fine) dealer checked codes, but said they couldn't find any problem, reset the codes, two weeks later same thing happened. Have appt to bring back in. When the check engine light is off, the car runs fine, there is no sputtering or shifting issues. Not sure what triggers the check engine light, but once it comes on all the troubles star


You need to change you crank shaft positioning censor ... 2006 Chrysler PT Cruiser

I have a 2005 Chevrolet Aveo and the check engine light came on and stayed on. We had it check and the code said that it was the gas cap. We replaced the gas cap but the light never went off. Then the hold light came on and the two started flashing on and off. Once the lights started flashing the car lost power and did not want to excell going up hill. The code the car is putting out is P0300. Where do I start to look to figure out what is going on with the car? The car has never had any problem


PO300 This code refers to a random misfire, this indicates an ignition issue. Random intermittent ignition failures are fairly difficult to diagnose, the first thing I would do is remove the spark plugs and inspect them, if they all have an appearan ... 2005 Chevrolet Aveo

I have a 2007 Equinox check engine light came on i scaned and got code p0036 and code p0054. I put a new denso oxygen sensor in ahead of the converter next to the engine,check engine light still on. I cleared the codes started the car 3 or 4 times and the light came back on,with the same codes.The car dont have quite 16.000 miles yet. Thank's kim.


That car is under warranty for emmision failuare, it a federal law, also you changed wrong sensor poo36 and poo54 mean o2 sensor after the cat-converter is no good not the first one by engine, replace the one after cat and problem will be fixed. goo ... 2007 Chevrolet Equinox LS New Cars

After receiving the error code p0036, (Heated o2 sensor 1 Bank 1) I replaced my o2 sensor, Cleared the computer and drove it for a day in a half.... Then the Check Engine Light came on again. After checking the code for that problem it came up P0046 The OTHER o2 SENSOR, (Heated o2 sensor 1 Bank 2) so I thought that maybe when one goes bad, they both go bad... So after replacing the SECOND O2 Sensor I again cleared the computer. Again after driving it for a day and a half the **** check Eng


... Cars & Trucks
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.0018 seconds