Having problems with your 2006 Jeep Liberty ?

2006 Jeep Liberty dying after installing trailer lighting harness.

\015 Installed frame hitch and T-style trailer light harness. Like the one listed here (http://www.draw-tite.com/content/products.aspx?lvl=3&parentid=1500&catID=1505&part=118524) Vehicle is randomly shutting itself off. Any clue if the lighting harness could be causing this? Bad grounding? Any suggestions are appreciated.\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2006 Jeep Liberty

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

2006 Jeep Liberty dying after installing trailer lighting harness.


... 2006 Jeep Liberty

INSTALL BRAKE LIGHTS ON TRAILER JEEP LIBERTY 2008 DIAGRAM


... Cars & Trucks

I purchased a trailer that did not have any wiring on it what-so-ever. I purchased all of the required parts (i.e. trailer flat four wiring harness, new trailer lights). I wired the trailer with the harness and installed the new lights. All of the lights work, but I have one problem. When I have the running lights on and then press the brake, the driver side trailer light goes out. The passenger side trailer light lights up fine when the brake is pressed. Both trailer lights work with the runnin


When this happens it is usually a bad earth on the trailer.But hey,check the car also.Check inside the trailer lights for a bad connection.It is an earthing problem.Mate.I hope this helps. ... 2008 Jeep Wrangler

2008 jeep liberty has the electronic throttle control (ETC) warning light come on as well as the Malfunction light indicator (MIL) and the vehicle wont start. PS had a towing harness installed a few weeks ago


... 2008 Jeep Grand Cherokee

OK I went to install a wiring harness and a trailer hitch on my wifes car. Went and got the correct Harness because of course the aurora did not have one. Installed it pretty easy per the directions....now I do not have a drivers side tail light or parking/running light but the other side is fine, so I took the harness back off and still nothing. This light worked fine the day before. I checked all of the fuses and also checks the lines.....the one that I identified to be the tail light and the


Check your fuses to see if you blew one pluging in your wiring ... 1995 Oldsmobile Aurora

Tail lights and sockets burn up only when trailer wiring harness is connected on my jeep liberty 2005


... 2005 Jeep Liberty

There is a short somewhere creating problems throughtout the truck. The short caused the taillight fuse to overheat in the fuse box and it melted in the box. The wiring for the trailer lights worked so I decided - not being able to locate the short- I installed trailer lights on the rear bumper and plugged them in to the harness. The lights worked for about three miles and I stopped at the store - checked teh lights and they weren't working. Mechanic installed a jumper - bypassing the the fus


Got much the same trouble... Well similar anyways. Started with burned wires in the harness above drivers side fuse box. Headlights stayed on even with switch off and key out. Then melting of the break light fuse ( bypassed that with an inline fuse t ... 1998 Toyota T100

I have a 2000 jeep wrangler 4.0 engine it ran good for 16 miles then would quit no check engine light on so i scanned it anyway came up with a p 1391 mis fire so i changed can sensor ran good about 30 minutes and died scanned again same 1391 i returned cam sensor and got a new coil pack and crank sensor i installed coil pack ran good about 30 minutes and died so i installed crank sensor and put back on old coil pack ran good 45 minutes then actually started missing and check engine light on it s


It does sound like the ecu is bad the only other thing it could be is the antitheft system is having problems ... 2001 Jeep Grand Cherokee

2004 liberty I was driving home from work in my 2004 Jeep liberty. The engine began to studder and the malfunciton indicator light came on and flashed. At a stop light the engine died and did start again but stuttered the rest of the way home. I have had no problems with my jeep in the past. Help! I only have 50,000 miles on it. Do regular maintance.


If your engine light came on, the engine module could have stored a code.\015\012You need to have a scanner to check what code it is and that will point you toward the solution.\015\012Possible causes could be (crank sensor, tps sensor or ... 2003 Jeep Liberty

2009 nissan frontier dealer installed tow package installed. Trailer lights work but trailer blinkers do not, checked wire harness tail to tow package and only have voltage for lights


... Cars & Trucks

2002 Jeep Liberty Ltd (2-wheel drive): Front right turn signal lamp, rear right tail light lamp, and dash lights all went out simultaneously when I hooked a U-Haul trailer up to my trailer hitch electrical system. The bulbs in the front and rear lights are working because I was able to pull the trailer with the emergency flashers on. Is this a crimped wire somewhere in the system, or is this a fuse story?


... 2002 Jeep Liberty

I bough tmy mariner used with a hitch and wiring harness already installed from the previous owner. i plugged it into a trailer and none of the lights came on. i then plugged it into another trailer and the trailer lights came on minus the use of the hazards, right turn, and brake lights. i looked at the box under the bumper and found that the red wire has been cut. i looked around and found nowhere in sight a red wire. long story short, where does the red wire go to? and could i splice it toget


Try http://www.etrailer.com/faq-wiring.aspx. Sounds like you need to replace the converter. ... 2008 Mercury Mariner

I have a 2010 XLT Club Wagon E 350. It had reverse aid and no trailer towing package. I installed the ford wiring harness that had the trailer connectors (it replaced the harness from the connector on the frame to the reverse aids). I have no power to it and no trailer lights. This unit was built on May 27,2010 and ford had a change in the wirning harness on May 21,2010. what do I need to do to make this work. Alan


More than likely your van is just missing the required fuses and relays. In the fuse panel in the engine compartment there should be a 20amp fuse in location F48, a 20amp fuse in location F57, a 15amp fuse in location F58,and a 30amp fuse in location ... Ford E-350

I have a 2004 Ford Escape. I installed a class 2 Reese hitch and wired the trailer light harness from the rear lights. All my lights work on the trailer except the break lights. Do I have to wire the breaks differently from the other lights?


You should'nt have to,all you need to do is to run a wire from one brake light to the plug if your brake light is a two filament globe ie. tail/stop light you need to make sure that you connect to the brake light wire.....hope this helps....cheers ... 2004 Ford Escape

Does the 2000 nissan sentra have a trailer pkg plug under the trunk area to hook up their OEM trailer harness? Bought a used trailer and don't want to screw up the auto wiring when I install a non OEM harness. I know that Nissan uses a non standard tail light configuration.


... 2000 Nissan Sentra

My 2003 jeep liberty has been turning over fine but randomly dies while driving, the engine light and oil light come on. All fluids are good, and I can turn it over fine after it dies but it doesnt last long before dieing again.


Have the alternator checked. ... 2002 Jeep Liberty

I have 2002 jeep grand and only with the lights on the right brake light goes out when stepping on the brakes. left and third light works fine. With lights off the brake lights work as designed. I've disconnected my after market trailer light harness and changed the bulb just to eliminate them. No problems with the turn signal lights.


The right brake light has lost its ground. It's a fairly well known problem on the '99 to '04 Grands. ... 2002 Jeep Grand Cherokee

I have a 2004 jeep grand cherokee i installed a 4 way flat plug for a utility trailer. I installed as instructions said but have no brake lights on the trailer, Everything else works. can you help me?


You will need to add an trailer light adaptor for this vehicle. this adaptor will combine the brake and signals from two separate sources. this unit can be purchased at walmart, Canadian Tire, Partsource, autozone. trailer shops. it will fix your ... 2004 Jeep Grand Cherokee

I installed a trailer brake controler on my 2003 silverado 1500hd with the kit that plugs into the factory wiring harness and the trailer brakes worked fine but the brake lights and the cruise control do not work any more. I replaced the brake light switch and I am still having the problem. I also checked all the fueses and they seem to be all fine. I have the controller unplugged now and the same thing is still happening. Any ideas please let me know.


Check 25A fuse under the hood.\015\012Check 15A stop light and 10A turn signal fuse under the dash.\015\012If all fuses check out, verify that the switch is operating the brake lights. ... Chevrolet Silverado 1500HD

I need a wiring diagram for 2002 jeep grand cherokee for trailer light install with a universal trailer light wiring plug


Also try http://www.etrailer.com/faq-wiring.aspx. They have easy to follow directions and color codes. Plus you can order anything you might need. Hope this helps. ... 2002 Jeep Grand Cherokee

I have a 1993 Chevrolet S-10 and just recently purchased a 5'x8' utility trailer. I need to know how to properly install the wiring harness to the truck so the trailer lights will work correct. It's a 4 post harness...Thank you in advance!


Yellow left turn, green right, brown taillights, white ground ... 1996 Chevrolet S-10 Pickup

Tail light circuit burned out from trailer harness


IM LOOKING FOR SERVICE MANUAL TOO. HOPEFULLY DOWNLOADABLE ONE.\015\012ANY HELP ([email protected]) ... 2005 Jeep Liberty

2003 Jeep rubicon no brake lights or hazard lights all the other lights work checked fuses and bulbs they are ok but not brake lights even the light on the trailer hitch harness is working


... Cars & Trucks

2003 jeep liberty left rear running light out. all other lights working. replaced bulb then plug in socket, then entire lens and no change. could it be the wiring for this light only ? how do i tell whch wire is for running light? there are 5 wires in harness.


... 2003 Jeep Liberty

Started with the lights, inside and out flashing on and off we resouldered the light switch. the radio did not work so we installed a new one and a couple wires touched each other and sparked not the blower motor will not work the indicator light that shows time date and problems is not working. the auto headlight sensor on top of the dash is flashing as if the hazard lights are on and when you start the jeep it runs for a couple seconds and then dies. None of the fuses were bad so we changed it


What year jeep and model are we speaking of? Did the soldering of the switch resolve the light flashing issue? ... Jeep Grand Cherokee
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.4103 seconds