Having problems with your 2006 Jeep Commander Limited ?

My code that came up when the engine light came on was PO521

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

P0521 Jeep - Engine Oil Pressure Sensor/Switch Circuit Range/Performancexicon.jpghttp://engine-codes.com/p0521_dodge.htmlForum CodePossible causes- Low oil level or motor mechanical fault
- Open or short oil level sensor circuit condition
- Poor oil level sensor electrical connection
- Faulty oil pressure sensor\011\011\011
Repair Help & Product Troubleshooting for 2006 Jeep Commander Limited

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have 1997 F150,check engine light came on, took to mechanic, code P0443(evap system code)came up. Replaced evap purge solenoid, smoke injection test for leaks, everything seemed to be working correctly. I recieved truck, drove for about 60 miles, check engine light came on again, same code(P0443). Checked system for leaks again(still no leaks), brand new evap purge solenoid functioning correctly. Received truck drove for about 30 miles, check engine light came on again with same code(P0443), w

Maybe a fuse is blown? did you have the mechanic check the fuses? or even check all your relays and wiring? ... 1997 Ford F150 Regular Cab

I have a 1996 chevy tahoe with a 5.7 vortex engine originally check engine light came on code reader said mis fire in cyclinder 3 and 4 so a mechanic friend tuned the truck up plugs ,wires,cap , rotor ,all 4 oxygen sensors after all done he reset the engine light the truck ran great for a couple of days the check engine light came back on he rechecked and code reader said misfire cyclinder 3 and 4 again he reset the light and did a compression test it came out 85 lbs on cyclinder he said it shou

... 1996 Chevrolet Tahoe

I have a 2005 Chrysler Town & Country with almost 100,000 miles. The check engine light came on about 2 months ago and the code said the O2 sensors needed to be replaced. About a month later, the check engine light came on and the code said the catalytic converter needed to be replaced. Now a month later again, the check engine light came on, the exhaust smells rotten, we are getting about 1/2 the miles per gallon and the code says to check the Mass Air Flow Sensor. Does this all make sense?

There are no codes that say replace O2 sensors,or remove converter,Thats just somebody's guessing,When it says O2 sensor that tells the mechanic to look for trouble in that area,wiring or faulty readings,And there are four O2 sensors. ... 2005 Chrysler Town & Country

Engine light was coming on so i hooked up my obd2 and code P0442 came up. tightened gas cap and cleared code but engine light came back. Replaced cap and cleared engine light again but engine light returned, what do i do next?

Try disconnectin batt cables and touch them both together--if no relief then theres something complex--put a tech ll that runs a data stream for the solution--some caps are sensitive so replacin with and original may work ... 1999 Chevrolet Malibu

I have had a Check Engine Light on my dash for a good 3 weeks. I noticed the Van running really ruff. I took the van to autozone and got the codes ran. The code of P0303 (cylinder 3 misfire) came back originally so I changed the plugs and it fixed the problem. About 1 week later I got a check Engine light again. I then again got the codes ran and this time it came back P0304 (cylinder 4 misfire). I then changed the plugs again, a day later the light came back so I changed the wires. Then a day a

I agree with phillyboy. Don't buy a compression gauge though. Pay a garage to check your compression. $40 or so.There are three rings on a piston, a compression ring, an oil ring and another compression ring. If your rings have failed on cylinder 4, ... 2001 Dodge Caravan

I have a 2007 Equinox check engine light came on i scaned and got code p0036 and code p0054. I put a new denso oxygen sensor in ahead of the converter next to the engine,check engine light still on. I cleared the codes started the car 3 or 4 times and the light came back on,with the same codes.The car dont have quite 16.000 miles yet. Thank's kim.

That car is under warranty for emmision failuare, it a federal law, also you changed wrong sensor poo36 and poo54 mean o2 sensor after the cat-converter is no good not the first one by engine, replace the one after cat and problem will be fixed. goo ... 2007 Chevrolet Equinox LS New Cars

I have a 2006 dodge magnum 5.7L HEMI AWD. I was drving and all the sudden the car shut off without warning (the oil light came on as it died) and i had no power or steering etc. The car would not start again and had to get it towed. When at the shop the engine light came on as well as the oil light and still does not start. Plugged into the computer and came up with 17 codes. the mechanic fixed the 17 codes, the engine light went off but still does not start. he thinks that is a crank sensor whi

... Dodge Magnum

U0155 code while driving all the gauges went dead the low fuel light,check engine light and the security light came on. The jeep kept running for about 30 seconds then just died after stoping turned the ignition off then restarted it everything came back on but the check engine light stayed on. Had the parts house read the code it came up u0155 they said the mic,pcm,or the tcm were possible causes just looking for ideas before towing it to the dealer.

The U0155 means "Lost Communication With Instrument Panel Cluster(IPC) Control Module"._________________autoco ... Jeep Wrangler

My code that came up when the engine light came on was PO521

P0521 Jeep - Engine Oil Pressure Sensor/Switch Circuit Range/Performance ... 2006 Jeep Commander Limited

Code drive 5 . My 2004 trailblazer posted a code "drive 5". It showed the "reduced engine poweer" light, and would not respond to the accelerator pedal. I had been driving in slow traffic. I pulled over, turned the engine off, and restarted it. The reduced engine power light went off, and it drove fine, but the service engine light stayed on. The next day, I filled it with gas, and then the service engine light went off. Then I had the code read and it came up "drive 5".

Thottle body sensor, accelerator pedal sensor, restricted air flow...will all trigger this fault light. Go to your local Autozone, they will run an OBD scan for free, and explain the fault codes to you so the correct repairs can be made.Good lu ... 2004 Chevrolet TrailBlazer

Engine light came on, had a p304 code. Took car for repair, mechanic could not figure out why engine light came on. Cleared light, car started to hesitate when stopped, engine light came back on. Spark plugs checked, engine light still on

P0304-misfire no 4 cylinder--can be bad plug-coil -wire-problem with 02 sensor--fuel injector-bad exhaust valve-cat conv- poor ,compression -these are most of the reasons that an cause a misfire and yours is specifying the no 4 cylinder ... 2001 Ford Focus


... 2007 Lexus ES 350

2003 intrepid while driving the check engine light came on went to autozone and had it put on diagnostics,trouble codes-p0841,p1776 and p0700, all showed up , once i started the car to return home . The check engine light wasn't on any more.i drove home with no light on the next day it came back on the. Went off I had it retested and no codes were found , I'm very lost and confused on this someone please help the car has 144.234 miles on it.what does the Code - p0841 mean also

... Cars & Trucks

1998 Tacoma V6 ext cab 184,000mi. Engine light on, per mechanic read knock sensor and shift solenoid. Took top end off and replaced both knock sensors, wire harness for sensors and checked grounding, and also put on new cat converter to get it to pass smog. No go. Engine light came back, ran code again, still said knock sensor, so he suggested trying a different ECU. Worked for a few minutes but engine light came back. Running rough. Ran code again and its the same, but now saying both knock sen

... 1998 Toyota Tacoma

Check engine light came on, ran codes and got miss fire on #6 hole. changed plugs and cleared code, light came on again. ran codes and came up with P0440 evap. checked lines and found no defect. cleared code again, light came on again after about 3 days. thinking it could be the gas cap but installed a new after market cap about 6 months ago. could it fail that quickly? also charcole canisters never been replaced...Dealer item? can you clean them? any help?

Would guess that canister would be dealer only but never hurts to check the local parts store.Could also check online parts store.They say this problem comes from topping of your tank.When fueling and the pump shuts off you are not to put any more in ... Buick Regal

PO336 code My wife drives a 98 malibu LS 3.1 V6. Last week the check engine light came on and showed a PO336 error code. I had the crankshaft position sensor and the harmonic balancer replace. The code was then cleared. The check engine light came back on after just a few minutes. What else could cause this code?

Cam Sensor ... 1998 Chevrolet Malibu

Put gas in 2005 chevy silver ado, next day service engine light came on. Pulled codes and came up with p0440 and p0327. Cleared codes and drove for 5days. Put gas in last night now service engine light on again. Have not pulled codes yet. Can one code have anything to do with other or just coensidence that after putting gas in it comes on

... 2001 Chevrolet Suburban

I have a 99 dodge grand caravan. Over the weekend the check engine light came on. I stopped at Advanced Auto Parts and had them check it for the code. Nothing came up and the light eventually went off. This morning, when I started the van, the engine light came on again and the van was running and ideling rough. As I was driving it to work, the engine light started flashing at me. I think the first time was around 7 times, the second time it blinked 10 times, and the last time before I got to wo

The flashing engine light indicates that one or more cylinders are misfiring. If possible take to Advanced again and have them give you the code numbers. If you post the codes in here we may be able to help find a solution to your issue. Would start ... 1999 Dodge Caravan

My 2002 Isuzu Troopers Check Engine light and Reduced power light came on and the engine ran very slow and sluggish. Checked the next day and check engine light came on and Reduced power light was no longer there. Had computor diagnoses and codes P1295 and P1515 showed up. After computor check, check engine light went off and I've had no more problems, but don't trust it to drive very far. What would be the most ovious problem?

1295 simply indicates that you were in "get you home" mode. 1515 has to do with throttle position sensor fault. Since it was intermittant I'd check for chafed or broken wiring and loose connections ... 2002 Isuzu Trooper

I just purchased a 2000 lincoln continental for my daughter. She said that the service engine light came on and after that the transmission light came on and went off and came on again. I had the mechanic check it and he said I had a code P1744 and that he would need to check for corrosion and that I need a transmission gasket due to leaking. Could the code P1744 also mean the transmission is going? Also I was told that the top side engine mount is cracked (Dog bone). Is that neccessary to repla

Top mount when go's bad eventualy can mess up other thing's, As for the tran's i would change the fluid and the gasket and filter. They are all right there togather, should cost around $75 ... 2000 Lincoln Continental

Always had a problem with 2006 grand prix GXP 5.3L V8 "using" lots of oil. This weekend check engine light came on, tech told me it was an oil pressure error. Added about 1.5 pints, reset the code, but it came back on later in the day. Hubby took it back in, resest the code , but light came back on. Tech said its either the oil pressure sensor or the oil pump. Engine is NOT knocking or sounding like its about to break down...how do i know what the problem is? I can't afford to fix both...

... 2006 Pontiac Grand Prix

Have a 1996 Isuzu Trooper LS, check engine light came on so I checked it with a scanner and it said generic code PO 133, which is a slow response, or slow switching so I put an oxygen sensor on, check engine light stayed off for a while, but then came back on with the same code. Would the map sensor or any other sensor make this code show up.

I had the same thing. It is something to do with emissions apparently. I was told to check the fuel cap ! I put some silicone on the seal, cleaned it up, put it back on with the correct number of clicks and after about 15 minutes of driving, the C ... 1996 Isuzu Trooper

I have a 2002 Dodge Intrepid ES 3.5L and on the way home this evening my engine light came on with a 440 code. I replaced the gas cap and just replaced the crank shaft sensor 5 days ago. The engine light came on for that with a 0016 code. The car has approx 106,000 miles on it and it did pass smog just 3 days ago. Can these codes be related? Any ideas? Thanks!

Try to disconnect the neg and pos charge to the battery almost every newer car has a computer in it it may be that the computer just needs to be reset ... 2002 Dodge Intrepid

On March 25th I sent my Nissan Pathfinder into a shop to fix a check engine light. The code that came up was P1456-Vapor canister Check Valve. They fixed it. Then April 3rd the check engine light came on again. Once again sent car to same shop and now code P0138 Bank-1 Sensor2 heater circut malfunction came up. Is this common or should I question the shop I take my car to?

This is common with heaters they dont last forever aslong as they are willing to show you the different codes at different times there problay being honest dont be suprised if they suggest replaceing all the o2 sensors at once its actually cheaper ... 2002 Nissan Pathfinder

I have a 1998 Audi 2.8 Quattro and last week the Engine Light came on and the car lost power. The technician hooked up the computer and the code came back: P0102 - Mass or Volume Air Flow Circuit Low Input. The tech changed the Flow Sensor and it seemed to fix the problem. Yesterday the Engine Light came on again and the car lost power. The technician hooked up the computer and got multiple codes: P1338 - Camshaft Pos.Sensor,Bank1 Open Circ./Short to B , P0300 Random/Multiple Cylinder Misf

... 1998 Audi A4
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.9663 seconds