Having problems with your 2006 Hyundai Sonata ?

Blurry flat screen computer monitor Almost impossible to read. 17" Hyundai about a year old.

\015 Monitor screen is blurry. Almost impossible to read. I would describe it as "glittery " Hyndai flat screen is probably about a year old. Embarq(dish network phone line) says it is not their problem. Thank you.\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Have you tried upgrading your drivers? or changing the screen resolution?
Repair Help & Product Troubleshooting for 2006 Hyundai Sonata

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Blurry flat screen computer monitor Almost impossible to read. 17" Hyundai about a year old.

Have you tried upgrading your drivers? or changing the screen resolution? ... 2006 Hyundai Sonata

I used to get a voltage reading of 13.6 volts on the electronic dash of my 1997 C5 but after the battery ran down ( 4 1/2 years old )the battery voltage now reads 13.2 volts on the electronic dash. I started the car while the flat battery was flat using jump leads and all seems OK except except the battery voltage. The alternator seems to be charging but is the 13.2 volts due to the battery being old ? I believe the right voltage should be 13.6 to 14.4 volts. Malcolm Place - East Sussex UK

13.2 volts is all your tired old battery can hold.anything above the 12 volts it's rated at indicates it's charging OK.it may increase again,but nothing beats new.consider a battery tender to keep it fresh if it sits for long periods. ... 1999 Chevrolet Corvette

1995 Cadillac has sat for 7 months.Altinator is 2 years old and batt is 1 year old.Dash computer reads BATTERY NO CHARGE.Is there a way of unplugging the alternator to wire brush the points or is there an other problem ? Batt terminals are good.


I have a 2010 Kia cerato koup. Have the car for almost 2 years now and it seriously isn't feeling as fast as it used to be. When it was about one year old it could do 170km/h on this stretch of road just up the street. Tried it again today and had it flat the whole way, I could only manage 150km/h and couldn't even make it to fourth gear even with the air con off. The car was feeling even slower until I got it serviced last month which gave it abit more power. Now what to do

... 2010 Kia Forte

I have a 2000 Hyundai Accent 1.5 L, and the check engine light keeps coming on. I have read the codes on OBD II and found that it is P1123 that is the only code that shows up. I have changed both oxygen sensors and still get the check engine light. Is there any way of checking that the oxygen sensors are good or not? The MAF is less than a year old. Is there any way to check for fuel injector leaks? If so how do you do it? Do you have any suggestions on what can be done to rectify this problem?

Locate the ruel pressure regulator on the fuel injector rail- pull the vacuum line off it and turn the key to "run" position. You may see a small geyser of gasoline from that hose connection as the fuel line pressurizes. If so- replace the regulato ... 2000 Hyundai Accent

I have a 1995 Buick Park Avenue that has been sluggish for some time and gets very poor gas mileage. It just so happens that none of the diagnostic computers want to read this car because it is what they call the half and half. It's inbetween the years that they changed from the old system to the new. Anyway I have been told several times to replace the mass air flow sensor. I was just getting ready to do this when these mechanics told me they did test the fuel system and it is telling them

The only thing that would make a fuel pump lose output pressure when you brake is dirt (or water) in the fuel tank - when the fuel gets sloshed around the dirt temporarily clogs the pump admission tube. You should take the tank out and clean it thoro ... Buick Park Avenue

2004 BMW 545i i want to autozone and they check the battery And it was good, but the alternator was not, So i got one, after replacing the alternator  I m stall having problems, the computer screen flash on and off All the lights come on like a christmas,  transmission fault, flat tire, The battery goes down, it runs like ****,, the engine light comes on And it says The Transmission fault. and then I have to charge the battery to get it to start again,, I was reading about the IVM Were is it loc

... 2006 BMW 545i

I have a 98 mirage LS Coupe 1.8. The check engine light was on and it was for misfire with cylinder #3, it turned out to be the Spark plug was bad. it was changed. the code on the computer was cleared. now i have the promblem were monitors have not reset so now i cant smog the car. i have been driving the car its been more than 500 miles and nothinbg yet. How do i get the computer to read the monitors?

... 1998 Mitsubishi Mirage

Intermittent poor acceleration, loss of power. Has new plugs, ignition module, crank sensor, fuel filter. Plug wires 1 year old. Have tried mass air flow sensor, coil packs. Fuel pressure was monitored and checked okay at 40. Applied dielectric grease to coil pack and module contacts and ran great for 20 miles. Pulled battery cable to reset engine code 42 and started running poorly again. Idles poorly now and jerks and hesitates when accelerating. Side note; battery 3 years old. frequently will

... 1992 Buick Park Avenue

I have a 1989 rivera, was told my ecm was good but the prom was bad. when ecm was pulled it was out of a 88 olds 88 special. Have bought four so far none work 100%. I tried Buick to get the computer [ecm]and the prom number all they can tell me is it's no longer stocked and there is no olds dealer to ask about the olds ecm I have now and it has been in the car since before I bought it eight years ago and worked perfect till this problem. I found a rivera ecm up north was assured it was the right

Ron it was great talking with you and we will get you on the right track soon here. make sure you pull the codes out of the computer and i will talk to you tomorrow. ... 1989 Buick Riviera

I have a 1990 Dodge Ram B250 conversion van the problem is the check engine light is on ran computer code to find out the problem. the engine is a 318 have a problem with the charging system have replaced the computer had the battery,alternator checked out o.k. getting fault code:1-2-40-1-5-5 what does this mean since there are no scanners available to read the computer code on this model year the van dies will not start until jumped, and it repeats the problem all over again HELP!!!!!

The numbers are 12, 41, 55\015\01212- direct batttery inut to controller disconnected within last 50 ingnition key-on cycles\015\01241- alternator field circuit- an open or shrted condition detected in the alternator control circuit. ... Dodge B Series Cargo

TPMS light on dashboard of my 2007 Hyundai Sonata with 77,000 miles. First came on 3 hours after I had the the right rear tire repaired with 2 nails in sidewall from independent tire dealer. Took back to Hyundai to reset the system but came back on again after driving 3 hours. Took back to Hyundai dealer again and they replaced the TPMS sensor in the right rear tire. Said they saw evidence of fix-a-flat inside tire but I informed them that I never ever used that. Their computer indicated that I

I don't know enough about the TPMS systems to give you any clue as to what is going on there.\015\012\015\012However, it is generally an unacceptable practice to try to repair a tire that has a puncture in the sidewall. The flexing of th ... Hyundai Sonata

That question didn't make since to me either when I read it. It's even the wrong year for my truck. Here is my problem, I have a 2004 f150 4x4 and the rear (back one) u-joint needs to be replaced. But I don't see any way to remove the old one. The "old" spring clips are not there, only dimples in the metal around to old u-joint holding it in. How, or can, I get is out. Ford calls this driveshaft "unservable" but the parts store sold me a u-joint they say will work???Can you help me?

You may have to remove the drive shaft and take it to a machine shop,were they would grind out the retaining tabs remove the joint,install the new one and tac weld retainers to hold it in. ... 1994 Ford F150 Styleside Supercab

When the Jeep was new the volt meter read 14 volts....now the volt meter reads 13 volts with a one year old battery. Since the battery is a 12 volt battery should there be any concern that the volt meter reads 13 volts rather than 14 volts?

Generally the standard voltage should be 13.5 to 15.5 depending on the load that is being put on the vehicle and age of the battery an older battery may require more voltage to charge. Unless the voltage drops below 13 you are probably ok. ... 1996 Jeep Grand Cherokee

Code-Screen I had my car fixed two years ago and the Mechanic told me that he went undr the dashboard and pulled all the codes from the ECM to make a repair. I had to replace my battery about 3mos ago and when I tried to put the radio code in on the screen but no code request came up on the screen ( just a flat line like this came up ----- ----- ----- ----- ).I remembered the mechanic remove the code connection(s) from the ECM.I can't locate the mechanic any longer to have him reconnect whatever

Try leaving the key on for an hour it may just be in code lockout mode -jeff ... 1995 Saab 900

2004 BMW X5 4.4i Left lights on resulting in flat battery. Car was jump started from another vehicle (Ford Transit van). Everything fine for a few days. Now, intermittently the radio/sat nav goes haywire! The screen flips open and closed on it's own over and over again to reveal the tape deck, the screen flickers on and off, it jumps from CD to radio to sat nav, screen displays 'monitor shutting down due to high temperature'? all this even when I've taken the keys out of the ignition and the car

Sounds like your car has the multi function steering wheel, i know on the 7 and 5 series they come out of sync, im not sure why.\015\012its about £75 to get plugged in at the dealers and they reprogram it, sometimes i have had the odd car ... 2009 BMW X5

1999 silverado 1500 LS computer reads Catalyst monitoring(C)not complete,Evaporative System monitoring (EV) not complete,A/C System Rrefrigerant monitoring (2A not monitoring.fail smog test twice,was told to drive it for awhile , i put like 450 miles on it still not complete and disconnect negative cable to reset it still not complete.What should i do next,can you help me . Thank You.

... 1999 Chevrolet Silverado 1500

So the service tire pressure monitor came on, so I checked all tires and made them 35 psi and I can't get the service tire monitor system to turn off. I can get to a screen in the car that says tire learn, so I turn the tire learn on and nothing happens, I can't enter in the psi and it doesn't read it. So is there something I'm missing?

TPMs, or pressure monitors can activate under cold weather conditions, it could also be from a faulty sensor or cpu. The TPMS is a separate system and has nothing to do with the regular maintenance interval of the vehicle.Do you have the ... Pontiac G6

I have an 03 Olds Bravada. I have had it for about 4 years. The service engin light comes on and stays on. I have taken it in to serice and the code is almost always that I didn't fasten my gas cap tight enough. Also for the past several years I have had trouble with the speedometer going crazy. When I'm driving it will shoot up to about 40 miles more per hour than I'm actually driving. It will get stuck for awahile and then reset itself after several days. I have noticed that this occurs more o

Hello\015\012The problems/warning indicators u have are most likely not related and likely are all separate issues, they are each related to sensor failures and other issues such as defective wiring, each one of ... 2003 Oldsmobile Bravada

My 2000 Hyundai Elantra is stalling intermintantly as I slow down at stop signs/lights, etc. I have noticed that the speedometer is not working properly.....i.e. when I'm moving at 30 mph the speedo is reading 10 mph ? But no engine lights are present.... I would think that this should cause a speed sensor/throttle sensor/fuel type sensor to activate a light ? Is there a possibility that the computer is bad ? Is the speed sensor external ? and is there a seperate computer for the transmission ?

According to the Hyundai service website, "If there is an open or short circuit in the vehicle speed sensor signal \012circuit, the engine may stall when the vehicle is decelerated to a stop." This sounds like what you're describing, so you should ch ... 2000 Hyundai Elantra

Daewoo Lacetti 1.6 - ever since the car was about a year old the check engine light has been on. The SERE engineers said it was nothing to worry about at each service interval. For the last year the car has been losing power to the point it is dangerous to drive. i recently had it hooked to a computer and the only thing it says is 'multiple mis fires'. I had the leads, plugs and coil pack changed. Light stayed off for a day! It drove like new for a week, then the problem has come back. I've just

Try buying a cople of bottles of wynns fuel cleaner from halfords let youre fuel get realy low then add both bottles to youre fuel tank and fill youre tank up just over halfway with bp ultimate then drive as normal this should clean youre fuel syterm ... 2002 Daewoo Nubira

Starting issues, I have had my 91 LTD Crown Vic for almost 3 years, it was a sheriff's car. the odometer stopped at 186k before I owned it so who knows where its actually at. And the check engine light flashes almost anytime i accellerate.Unfortunatly its too old for the diagnostic machines in most autozones. I have replaced the battery 3 times now, the alternator, starter and shifter hidge arm. but i continue to have starting issues. Granted its winter in Florida so i know im not gonna get the

Have your battery check first.ive never seen a battery that will last for 5 years.shelf life starts as soon as the acid is added to the battery. ... 1991 Ford LTD Crown Victoria

Flat battery after 31 mins when either closing the doors or locking the car , the 4 door interior side lights come on and stay on if the car is not driven within a 24 hr peiod then a flat battery does anyone know what would activate the 4 interior door lights after shutting the doors ( 30 plus mins later ) no other items are on in the car no alarm turned on ( factory one fitted though ) the car is two years old now with 70,000 klms on it and today we had the battery replaced but same problem is

Sounds like the timing unit which automatically turns off your dome lights after a few minutes is working backwards. Probably need a new unit. ... 2006 Mazda Tribute

4 month old 2008 x5 with 4,000 miles .Are away on vacation 500 miles from home. Car sat out in the rain and heavy fog overight. This morning I started the car,put it in drive and started to move when the car suddenly went into park and the screen read"Before leaving the vehicle secure it against rolling" and the screen showed a picture of a car with arrows pointing out from the front and rear of the car. The car also shifted into park when I put it into reverse. Over the next half hour the car

This happen to me after I got into a small fender bender. The dealership stated this only happens when something is not closed correct (door, hood, etc) ... 2007 BMW X5 3.0si SAV

My hyundai santa fe no start I change the computer and doed the same thing i watch the light for check engine no show did the same with the old computer,now what I can doed??

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about y ... 2002 Hyundai Santa Fe
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.9606 seconds