Having problems with your 2006 GMC Yukon Xl Denali ?

Which fuse controls the running lights for my trailer?

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2006 GMC Yukon Xl Denali

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1999 Town Car Running Lights Not Working... I have a hard wired a flat-4 trailer light receptical that I use occasionally. It has worked fine for me for the past several years. A few days ago I connected to a trailer that was mis-wired and later discovered that the cars running lights (front, rear, side marker and License plate lights) no longer work. I figured I blew a fuse, but I checked and they are all fine. My next thought was I had fried the Lighting Control Module (LCM). I bought a used L

Hello! Since fuses did not blow I would suspect that when you plugged in the trailer excessive current flow may have damaged the LCM...However to install another at random with the same fault is rare...Check fuse #31 just to be sure...Drop the LCM ba ... 1995 Lincoln Town Car

Which fuse controls the 7 pin connection running light for towing a trailer. My running lights and turn signal on the trailer do not light and the wiring is good. 2007 Toyota Sequoia with towing.

... 2007 Toyota Sequoia

I have a 1997 Ford F150 4x4 Supercab Stepside with 5.4L and factory towing package. On the factory trailer wiring plug I am not getting power for turn signals or brake lights. Running lights and brake controller work fine. I have checked fuses, and one was blown, which I replaced to get running lights working. But I still do not have brake or turn signals at the plug. Is there something else I can check before tracing the lines?

No, check the wiring in the rear going to hitch plug, they may have rotted or broke,if lights work on the truck then i would say its wiring,test wiring moving backward until you get power, this way you can pinpoint break location area, good luck, ho ... 1997 Ford F150 Regular Cab

Fuze #14 blown. this powers back uplamp,daytime running lamps relay coil, a/c pressure switch,cruise control, heated pvc,trailer tow back up lamps, abs, reverse park aid and ec mirror. the fuze blows any speed above 60 mph.I hear a metal on metal grinding for about 10 sec sometimes blowing the fuse other times it will grind two or three times before blowing the fuze.I have isolated the a/c, the running lights,and back up lights. I have also changed all idler pullys and belt. brake pads have also

I have the exact problem. Only difference is mine will blow fuse 14 at anytime. Mostly when I'm over 60 but has blown it at lower speeds.\015\015If anyone gets any info on this please let me know. This thread is the first one I've found ... Ford F-150

I actually have three issues electrically with my 2005 Envoy XUV. The most important one is the running lights. First the running light feed to the trailer connection ( factory installed ) fed no power to the trailer, I also found the fuses for the trailer turn signals both left and right were blown. I replaced them and the trailer turn signal and brake lights are ok but still no running light power from the Envoy. About a month after this the right rear running lights in rear turn signal brake

1) Look for fuse 32 in underhood fuse panel, I believe this is for trailer lights. 50 & 51 are for R and L trailer brake.2) The blower resistor pack is defective, this is located behind the glovebox and mounted to the blower body.3) I ... 2005 GMC Envoy

I have a 97 expedition that has the factory towing pkg. I recently went to plug in my trailer that has always worked fine with this truck and no brake or turn lights but running lights. I checked the fuse under the hood and it was blown. I have replaced it and still no turn or brake lights, just running lights. The fuse is still good, but I replaced it anyways. Still no turn or brake lights but running lights are ok, even with a wire bypassing the fuse under the hood. Now what?

\012put fuse back in (fire hazzard)\012check to see if got a broke wire at the trailer connector\012check wiring under truck at connector see if wire is bad (thats why fuse blown short ... 1998 Ford Expedition

Been having trailer light issues last i checked i had blinkers and brakes but no running light just attempted to go out and test the wires and some how have managed to lose the trucks blinkers/brake lights checked fuses all good except for the trailer tow right and left-hand stop/turn light fuses which arent recieving any charges went under hood check all fuses there all are good what is the next step to fixing my truck lighting issue?

It's a wiring problem and in most cases a grounding problem. Check the wiring with a multimeter. See that you have proper current on the hot side and also check ALL of the ground wires to see that they are really grounded. They sometimes get loose an ... 2004 Ford Explorer Sport Trac

Which fuse controls the running lights on a trailer

... 2007 Chevrolet Avalanche LTZ

I have a 2010 F250. The trailer brake and turn signals are OK, but the running lights don't. I don't know which fuse controls this under the hood. Can anyone help?

I'm going through this same thing with my 2008. I have already checked all of the fuses in the interior box. I believe the problem is in the "High Power" fuse box which is under the hood. In my case it is on the drivers side over the wheel well and u ... 2008 Ford F 250 Super Duty 4WD

Which fuse controls the running lights for my trailer?

... 2006 GMC Yukon Xl Denali

2009 Silverado 4x4 pickup with towing package and factory installed Trailer Brake controler installed at factory. The system has worked in past. I had my Stock trailer rewired and things tested out fine for lights and turn signals and brake lights. However, the trailer brakes do not work. I have checked all fuses for the trailer and they are OK. When trailer wheels are jacked up when using a DC charger to activate the brakes at the plug things are fine. On the trailer brake Control panel it does

It sounds like you lost a ground.\015\012check traier hookup first.\015\012Probably not the controller.\015\012P.S. There are multiple fuses for this setup. check all ! ! ! ... 1999 Chevrolet Silverado 1500

I have a 2008 Tacoma, I plugged in my trailer and lost my running lights or parking lights (tail), found a short in the trailer lights,resolved that...blew a fuse on the tail lights, changed it still no lights. Checked the fuse with a meter good. Still no parking lights..front and back ??

Hi...\015\012\015\0121.may be the bulb might have fused off. did you trying changing the bulb. if not try changing it and try it.\015\012\015\0122.may be the wire which connects the bulb have been busnt out before the fuse fus ... 2008 Toyota Tacoma

I have a 2004 Chev Suburban and my trailer running lights do not work but the stop and singnal lights do. Can this be a fuse issue and if so what fuse runs the running lights?

I don't know of many trailer equip with fuses. if the stop and turning light works than you will have to retrace the running lights wire which has a short ground. 12 volts light tester will be good tools to use. ... 2004 Chevrolet Suburban

Radio, Interior and reading lights, power doorlocks, voltage (battery charge level) meter,running lights all stopped working on one turn of the ignition. No smoke, no unusaul weather or circumstances. Running lights came back after fuse change but quit after one test run. Looking 4 fuse box diagram and wiring info for 94 plymouth voyager. Cruise control and AC have been down from day 1 of used purchase & I don't know if this might short out other circuts in the system. Also power mirrors are sho

... Plymouth Voyager

When I hook up my horse trailer to my 2003 Ford Excursion, it blows the fuse for the running lights. The blinkers and brake lights work, but that is all. If I change the blown fuse, it will only blow again. I had the plug changed because it appeared loose and that did not seem to fix the problem. When the place put a 25 amp fuse in place of the 20 amp, it seemed to be fine. Is it safe to use the 25 amp. or could it be a grounding issue with the trailer. The horse trailer is a 2006 Sundowner.

... 2003 Ford F250 Super Duty Crew Cab

My 2001 F150 odometer display light works when it wants to. The display on the radio is burned out. Now today I hooked up my 5th wheel trailer and the fuse to the turn signals/flashers blew out and the brake controller will not work. Changed the fuse and it blew again. I then hooked up my bumper hitch trailer and hooked up the 4 pin light connector and the turn signal fuse blew again. Same problem, two different trailers and two different hook ups. What could be wrong?

... Ford F-150


This can be found under the RAOSIDE EMERGENCIES section of your owners manual.\015\012\015\012HERE IT IS - in PD ... 2003 Ford F350 Super Duty DRW SuperCab

The fuse on my Hyundai Sante Fe trailer wiring system burns out whenever I turn on the running lights. The signal and brake lights do not burn out the fuse however. The running lights work fine on my Ford Escape. any ideas?

... 2009 Hyundai Sante Fe

I have an 07 titanand I cant get the running lights for my trailer to work. I have brake lights and turn signals but no running lights. I have checked all fuses that I can find and purchased a new relay..Are there any inline fuses?? Is there anyplace where i can get a wiring diagram??

Just to cover all bases, have you checked the bulbs in the trailer itself? These bulbs should be a double filament so that one setting is dimmer than the other. I would test the sockets for power when the system is hooked up and running lights are tu ... Nissan Titan

What fuse controls the hazard function. The hazard button disloged from the dash (over the radio) while I was trying to put it on and it is now somewhere inside the dash board behind the radio. My flashers (hazard lights) are now on and there is no way to turn them off with out taking the fuse that controls them out of the fuse box. My engine is still running to keep the battery charged and I do NOT want to run out of gas. Please help!

... 2004 Mazda 6

I have a 2004 pacifica and the running lights shut down when hooked to a trailer. No shorts in the trailer and the running lights come back on when the trailer is unpluged. this is a new thing, its worked in the past. can the resettable fuse fail? What is its amp rating? can a heavy duty one be installed?

There is no resetable fuse, the problem is in the trailer running lights, there is no other reason, check ever bulb socket positive contact for a short to ground.. ... Chrysler Pacifica

I have a 1996 Chevy C1500 5.7L Vortec. I hooked it up to a trailer and lost dash lights, tail lights and parking lights. All other lights work. Fuses look fine. Is there a fuse separate from the lighting fuse that controls the lights that are not working or is it a wiring problem?

There is a n instrument panel fuse and a tail light fuse. Check both with a 12V test llight not just visually. Sound like one of the are blown, probably the brake/stop light fuse. Usually the dash will darken, when a tailight fuse blows, sort of a sn ... 1996 Chevrolet C1500

My 2003 Silverado has a problem with the trailer lights. The stop lights and the hazard warning lights work fine, but the running lights and turn signals do not work. There is no current at the trailer electrical connector. I looked in my owners manual and found the "Center Instrument Panel Fuse Block" that contains a "Trailer 6-Way". But, I can see the center instrument panel utility block but I can't seem to figure out how to access the Trailer 6-Way to check it out. Can I get some quidan

... Chevrolet Silverado 1500

I have a 2001 Chevy Silverado which I use to pull a trailer. My trailer lights don't work at all - no running lights, no signal lights, no brake lights, etc. I have hooked up another truck to the trailer and the lights do work. I have checked my fuses and they appear ok. I have also cleaned the connectors. What should I check next? Thanks

The wiring harness is probably faulty. Get a light tester to see if power is going to the harness, and if the harness is receiving it by testing current flow on the connectors. it might just be that the harness is not receivng power and has to be rep ... 2001 Chevrolet Silverado

I have a 2008 Dodge Ram that came with the tow package. When I plug in my 7-pin trailer (with electric brakes) everything works fine until I turn on the truck lights. When I turn on the truck lights, I loose both of my turn signals and brake lights on the trailer. The running lights stay on. I unplugged the brake controller and still have the same problem. I compared my trailer plug diagram to my trucks manual and everything appears to be wired correctly.

If you have amber signal lights & red brake lights, it's 2 separate circuits. You'll need to buy a small converter that you wire into harness to correct that. Not expensive, try autoparts store or RV/trailer sales, should have them. ... 2008 Ford F-350
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.2900 seconds