Having problems with your 2006 Ford Fusion ?

Cant find cam position sensor 2006 fusion 3.0

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 2006 Ford Fusion

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cant find cam position sensor 2006 fusion 3.0


... 2006 Ford Fusion

2000 impala 3.4L. Trying to replace the cam position sensor located under power steering pump. Cant figure out how to get the pump out of the whole its sitting in. It will lift a little but cant find whats keeping it from coming all the way out.


... 2000 Chevrolet Impala

Cant find where the cam position sensor goes on my 2001 chevy blazer


Hello timrel: My name is Roger and I will help you. You will find the Camshaft position sensor located in the base of the distributor. Remove the distributor cap and rotor to gain access to the sensor. Should you need further help please just ask. Pl ... Chevrolet Blazer

I keep getting the check engine light on in my 2004 Hyundai Sonata with 2.7 v6. Computer says P0340 camshaft position sensor circuit malfunction. I actually replaced the cam position sensor but I still get the error codes. It actually has acted so bad that it says cylinders 1, 3, and 5 are misfiring. In the Haynes manual it says on V6 engines there are 2 cam position sensors, I can only find the one I replaced. I also gave it a tune up with new plugs and wires, all gaps were correct as well. So


... Hyundai Motor 2004 Sonata

I have a 1998 Ford Explorer V6 4.0L I am trying to find out were my Camshaft Position Sensor is located and can i get to it without having to remove any other parts such as air intake lines or anything like that if you could hook me up with a diagram or picture of were the Camshaft Position Sensor is located it would be much appreciated, even if you cant get a picture or diagram if you could explain were to find it that would be great. Thanks, Billy Blackwelder


It should be on the drivers side valve cover directly to the rear of the the oil fill cap, should have one bolt that holds it in place with two wire connector on it. ... 1998 Ford Explorer

Cam sensor the dealer ship is telling me there is a cam sensor magnet that is bad but i cant find any info on the magnet itself just the cam sensor replacement. any input


It is inbedded in the crankshaft on most GM models. ... 2006 Chevrolet Malibu Maxx

Cant find the cam sensor


The camshaft sensor on this engine was located on the passenger side of the engine. You will need to remove the serpentine belt, and you can get to it by removing the inner fender or splash guard and get to it that way. I went down from the top. Ther ... 1991 Buick LeSabre

Rebuilt my 454 engine, installed distributor with rotor at 0 TDC on #1 cylinder. Engine ran fine but ses light was on. Code was P1345-- disagreement between cam sensor and crank sensor. Scanner showed anywhere from 19 to 25 degrees advanced. Rotated dist. shaft. to ****** timing. Wouldn't run. Tried two teeth positions in either direction from original setting. Ever have a sensor go bad. The crank sensor is new, cam (on distributor) is not.


The ignition timing is not adjusted with a timing light or with the engine running, and to set the ignition timing follow these procedures.There is a mark or notch on the distributor housing that the rotor should be pointing to when the e ... 1998 Chevrolet K2500

I have a 2001 dodge 24 valve diesel and need to replace the cam shaft sensor, i bought the sensor but cant find where it is on the motor. where is the cam shaft sensor located on the motor?


It is located below the fuel injection pump in timing gear housing..not easy to get at..1 bolt and electrical connector..goes in from behind into housing..injector pump is unit with all the fuel lines coming out of it..have replaced these sensors bef ... 2001 Dodge Ram 3500 Truck

On my 91 buick lesabre it back fired now we are getting a code 41. Think it is the cam shaft sensor but cant find sensor on car. Where do i find the sensor. It is a 3.8 litre engine


... 1991 Buick LeSabre

1999 intrepid just stopped. Tried to start but wouldn't. Ok, I disconnected the cam positioning sensor and the car started and runs. It takes about 5 seconds of cranking because the crankshaft sensor needs to find the signal. The car lopes at high rpms. As long as the cam sensor is disconnected it runs but as soon as I connect it it won't start.


Id Try a New Crank sensor.. Lemmie know ... 1999 Dodge Intrepid

The Van (91 3.3L) will not start, It will turn over, and I have checked to see it I was getting any spark at the plug and NO SPARK. I have changed out the Computer ECM, emergency stop relay, Coil pack and the Camshaft position sensor. I understand there is a Crank shaft position sensor cant find it and am about out of things to try. Please help?


Look for the crankshaft sensor at the output end of the engine near the flywheel/flex plate area if the van is a Chrysler product. In GM engines, the crankshaft position sensor is combined with the camshaft sensor and is located behind the crankshaft ... Plymouth Grand Voyager

Cant find the crankshaft position sensor on my 94 topaz


... 1994 Mercury Topaz

I cant get power to ignitioncoil I have changed crankshaft position sensor,computer and fuelpumpTheris one fuse i cant find power to in fusepanel behind rightkick panel I cant read it well but it is the one under the airbag fuse its blue in color the fuse is good.I need some info thanks james.


Before you go any further you should have the diagnostic codes scanned then go from there.it may save a lot of headache.hope i helped.. ... 1996 Jeep Grand Cherokee

I have a 1994 chevy s10 4x4 4.3 vortec,where is the cam sensor or crank sensor (i cant find the crank sensor by the timimg


... 1995 Chevrolet S-10 CA Edition

My 2002 4.3l suddenly began to mis fire and stopped. with ciol disco it cranks over ok. the following codes showfault P0300 random cylinder miss fire,P0131,P0137,P0151,P0101 map sensor- swapped in new sensor,P0442 evap system. i cant see if i have a crank or cam shaft position sensor at this piont. cpu module tests ok what do you thing the problem is. i don,t believe timing chain is gone.


... 2002 GMC Sonoma Extended Cab

Cannot find sensor that energizes/controls the fuel injectors, they cant open, replaced the MAP sensor with a new oe, old one had about 440 ohms new 180, fuel pressure ok, fuel regulator ok, proper injector resistance and volts/ground, replaced Cam shift sensor,


There is no sensors which control the fuel injestors.There are relays which control the fuel flow through them and they are located on fuse panel block under the hood. It sits right in front of\015\012the driver, you have a single wheel- ... 2004 Chevrolet Malibu

How to set base engine timing/cam timing, 1998 ford contour with vct on exhaust cam. Can find tdc for crank #1 cyl. Can find base cam position for int cam. Exh cam has vct. can not find proper position or procedure to set base timing. Cam has spring pressure to hold cam in full advance position. cam does not seem to be retaining advance position when tension is released on cam. Is vct chamber on cam defective or what is procedure to set base timing for this cam? have sev tsbs for this, not much


... 1998 Ford Escort

Need to find Cam Position Sensor on 2004 Neon SXT


It isn't something you can just disconect, but it is fairly easy to replace. I just did mine about 2 weeks ago and it took less than 30 minutes. You just remove the battery so you can get to it, and it is right there on the side of the engine. Aft ... 2005 Dodge Neon

I have a 1995 buick lesabre and i changed control module,position sensor,cam sensor and computer. car stop and will turn but want start. when i first bought car it had this vibration on take off but never could find out what it was. need help


Are you getting gas and spark to the cylinders?\015\012\015\012If you add gas to the throttle body, does it start?\015\012If so, then you have a fuel pump delivery problem in this vehicle.\015\012\015\012If it doesn't st ... 1993 Buick Skylark

Where is the crankshaft position sensor on a 2002 crysler Sensor(Cant Find It)


I think Earl Norager should stick to lawn mowers and not cars. The crank sensor is at the top rear of your trans bell housing. ... 2005 Chrysler Town & Country

Have dodge stealth twin turbo ran fine then parked it.now speedometer not working and car will not go past 25-2700 rpm .already replaced speedometer sensor and throttle position sensor.car still runs like ****.cant find wiring diagrams ,just had rebuilt engine installed i suspect that i have apinched wire or one that burnt between speedo sensor and speedo head.


... Mitsubishi 3000GT

I just finished repairing the valves in a 1999 Daewoo Nubira after the cam belt broke. It now has new cam belt, pulleys, tensioners, head gasket, head bolts, and valves. I put it all back together and hooked up the battery and it started right up! Only problem is that it runs wide open all the time and won't idle. The throttle linkage is not stuck, and is sitting in the idle position against the idle speed screw. I can't find any sensor connection plugs that got missed, and my ODBII reader doesn


Map sincer check that if shorted to low or high it will make it do that check your throttle return spring it may be broken or out of ajustment ... 1999 Daewoo Nubira

In my 1995 Pontiac Grand Prix 3.1L I just changed the battery, alternator, crank sensor, cam shaft position sensor, and my car service engine light keeps coming on i cant get it checked at autozone or orielly cause of the ob1 system in my car nor can i afford the price for diagnostics at a car care place how can i figure it out without going for broke...i'm a unemployed college student


What was or is the original problem?\015\012\015\012You changed the battery,alternator,crank sensor,cam sensor. Why?\015\012\015\012If you got no OBD1 Codes,why would you throw parts at it?\015\012\015\012You could ... 1995 Pontiac Grand Prix

I have a 1999 chevy s-10 with a 2.2 motor. When I got it 2 injector was not working ,change crankshaft position sensor, cam sensor, and now change the ECM computer!! It will start but dies right after!! I could not find a ECM for my truck but a junk yard said that one out of a cavalier with a 2.4 would work ,so that the ECM I have in it but the # does match!!!!


1) replace your old ECM. 2) check cam sensor positioning. It's probably off. 3) Junk Yard jockey's are just that. Be afraid, be very afraid.... ... Chevrolet S 10
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.6239 seconds