Having problems with your 2006 Ford F-250 Super Duty ?
CAN'T FIGURE OUT WHERE COIL IGNITION ''B'' IS ON 2006 FORD 4X4 F-250 IS?
What you have is called a COP. the is known as coil on plugs hence C.O.P they are located on each cylinder they are black in color(well most are) and each of them have a 2 wire connection on it each one is held down with a 7mm screw. If you remove one underneath is a spark plug.
Repair Help & Product Troubleshooting for 2006 Ford F-250 Super Duty
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Ford Focus 2003 ,my car just burn3 ignition coils ,cant figure out the problem. I found this next to the coil : ignition/radio capacitor .Do yiu think this might damage the coil?
Time to see the dealer for in depth testing. ... Cars & Trucks
Ignition problem started truck up, it stalled and would not start. Getting spark, dist. button is turning, but am getting no spark. Replaced coil, still no spark? Called part store, said maybe ignition control module, cant seem to locate where they said it should be. Have a 1984 ford f150 300 6cyl 4x4. Any suggestions? Thanks
Should be on driver side over the front wheel ... 1984 Ford F 150
CAN'T FIGURE OUT WHERE COIL IGNITION ''B'' IS ON 2006 FORD 4X4 F-250 IS?
What you have is called a COP. the is known as coil on plugs hence C.O.P they are located on each cylinder they are black in color(well most are) and each of them have a 2 wire connection on it each one is held down with a 7mm screw. If you remove on ... 2006 Ford F-250 Super Duty
Restoring a 1953 ford truck v8 flathead 239 and cannot get fire to ignition switch, distributor or coil. I have tried everything. All wiring is new. have traced all of the wires. cannot figure it out. i have restored 1965 mustang, 1939 ford 2 door sedan and a 1954 ford crown victoria. I just can't figure this wiring out or whatever is wrong. thanks Frank
You should have battery power going into ign switch. if you do not then your wiring from switch to battery is open somewhere. i cant pull a schematic on this but would assume it is not connecting thru a junction block trace this wire back to its sour ... Ford F-100
1999, F150, V8 5.4L Triton, 4x4. When idling and at the beginning of each gear the truck begins to shake and no check engine light is coming on. I feel like it is an ignition coil, could you tell me which ignition coil to start at to figure out which one could be out. or tell me what else this could be.
... Ford F-150
I have a 1990 ford f150 and i cant get it to star it looks like there is no spark i change the ignition coil the ignition module and pick up coil and still not star
Do you know if your starter is bad? If you have not had this check perform these simple steps to check your starter. Place flathead screwdriver on top of your selonoid switch and another screwdriver to the positive battery terminal. If your starter i ... 1990 Ford F150
I got a lincoln Mark seven and i cant figure out why Im not getting any fire. New coil, Ignition Switch, Alternator, and wire. Amp light is on, check engine light aswel. Will start every once awhile, if i sit there and hold switch. Fire isnt even come threw Coil. When holding ignition switch motor turn over,then check engine light blinks off car stops right up.
Check the engine control unit itself and the ignition module. ... 1989 Lincoln Mark VII
I have a '99 Ford Ranger 3.0L that won't start reliably(3 times in 2 weeks).When I turn the ignition to "on",the theft light flashes rapidly,and will eventually give me a 1:6 code(faulty link between PATS module and EECV).I tried a regular door key in the ignition,and a 1:3 code flashed(key code not received)which tells me the transceiver is working properly.When it will start,the theft light works properly and proves out.The truck will start sometimes and runs fine,which makes me discount coil
When the anti-theft light is flashing rapidly then either it is not seeing the key,or the transciever module is not communicating with the PCM. It could be the transciever or it could be the PCM is not powering up for some reason. I would first try r ... 1999 Mercury Cougar
Wont Start 1988 Mazda B2200 wont start after replacing,plugs, wires,rotor,cap and coil. What happenned? Cant figure what possibly could have gone wrong. Have done my own tune-ups before with no problem. Just finished putting plugs and wires on my 97Buick Regal. Pulled my Mazda truck in the garage today and replaced the plugs ,wires, coil, rotor,distributor cap and coil. The ignition system doesn't have points and condenser. My repair manual says its electronic. Have had this tru
Sounds to me that you might have damaged the cap(dist cover) when you removed the coil btw you don't need to remove the coils on these trucks they last forever, so replace the dist cap with one from a junk yard with a coil in it and I bet you will ru ... 1988 Mazda B2200
Wont Start 1988 Mazda B2200 wont start after replacing,plugs, wires,rotor,cap and coil. What happenned? Cant figure what possibly could have gone wrong. Have done my own tune-ups before with no problem. Just finished putting plugs and wires on my 97Buick Regal. Pulled my Mazda truck in the garage today and replaced the plugs ,wires, coil, rotor,distributor cap and coil. The ignition system doesn't have points and condenser. My repair manual says its electronic. Have had this truck for about
Have another look at your plug wires, and make sure that you have them in the right order. As you probably know, if the firing order is wrong, you can have problems. That is somewhere for you to start, anyway. ... 1988 Mazda B2200
1994 Ford Bronco, 5.0 4x4, Wont start, replace coil, distributor, ignition module, coil has voltage, 12 to negative, 12 to power side when key is rolled but no fire out. 3 coils, switched,? Lost? Could it be the brain, or is it something to do with the fuel relay? The tank is not the orginal its asmaller one, with different style. Ran fine but now im stumpped.
Have you check power to coil when key is on crank position? you may have a bad ignition switch, do you have a fuel pressure gage? what it is reading? hope it helps, or write back ... Ford Bronco
2001 ford escape voltage light comes on intermitently, when it does the lights dim suggesting a loss of power. i have installed a new alternator and battery. no check engine light on. Ialso had a #1 ignition coil changed that was dead, this was a problem before the alternator failed due to bearing fatigue. in case it helps. crackle sounds are iregularrly heard threw the stereo speakers when the ignition is off, and the noise pops when the key (ignition) is turned on.
... 2001 Ford Escape
No spark i have a Ford 1300 Tracer in S.A. this is the Mazda Sting.My problem is the positive to the coil.I have a positive to the coil but not strong enough to get the unit to spark.I connect a direct positive to the coil and the car starts.Ihave spark.Ihave tested the wire to under the dash behind the radio and from the coil to that position is fine,i cant locate the wiring any further without pulling the dash apart.Does this wire go to a relay or to the ignition?
You'd need to track down a wiring diagram to be certain, but usually the power feed for the coil comes direct from the ignition switch contacts. If you take the steering column shrouds off and measure the resistance across the switch contacts that su ... 1994 Mazda 323
2003 ford e350 van ignition coil # 1 diagram for 5.4l engine
... Ford Cars & Trucks
2003 ford e350 van ignition coil # 1 diagram
... Ford E-350 Super Duty
1981 chevy 350/or 305?, it is a rebuilt engine, but when I set the timing at 0, 2,4,6,or 8 degrees it sounds good, however, when it warms up it won't start without moving the distributor. I checked the rockers on #1 cylnder at tdc. They are both closed. When I advance the distributor the car starts when hot, but doesn't have power. I am at a lost. I am thinking that it might be the ignition module, or ignition coil. Is there a way to tell? The engine is in a 1981 Caprice Classic and don't reall
Is your heat riser siezed? If it is siezed closed you have too much back pressure. You will need to free it up. To do this you may have to take the exhaust manifold off as it is situated in it. Use heat & WD40 to free it up. Good luck! ... Chevrolet Caprice Classic
2000 ford explorer input turbine speed sensor. code po715 was pulled on the obd scanner.does any 1 no were this sensor is located at on my transmission, i beleiv e it has the 55r5e trans but not quit sure. engine is a 4.0 sohc with over drive and 4x4 any 1 can help would be great im going nuts ovewr this. also auto zone sold me a input turbine speed sensor but i cant find the part they sold me any were on transmission, so not sure if thats even the rite part i need ...(i need the input turbine s
The is also known as sensoer c it is your pressure control solenoid. if you drop the transmission pan and remove the transmission filter it is on the side of the valve body. DO NOT REMOVE THE VALVE BODY PLEASE ... 2000 Ford Explorer
2001 ford crown vic spark plugs with coil over, want to change plugs but it looks like a fuel rail is in the way..how to change plugs without affecting high pressure fuel inj line. i got a code on my scanner that says 'cylinder 6 misfire', and all the wires going to the coil at 6 look fine. figure if i can just get to the plugs i could start there...but cant even get started
You can use a universal joint extension and a wobble drive extension to get to the difficult ones ... Ford Crown Victoria
Cant figure out the pattern of the ignition coil wires i had to pull them and i cant put them back right
The 92 model says 4.6 so the bttom one should be it ... 1992 Ford Crown Victoria
I have an 05 town and country stow and go 3.8liter.My scanner says cylinder 1 misfiring and i already replaced plugs,wires,egr,coil pack and # 1 fuel injector and my van is still misfiring.I cant figure it out unless its some wiring.whatcha think?
Other than a bad scanner, you have got something going on there, Is it missing or just telling you it is missing? Did you try another wire in the No. 1 spot? Did you look at it running at night?(light show) Try separating the wires going to No. 1 and ... 2005 Chrysler Town & Country
My 95 Ford Escort wont start, changed ignition module, ignition coil pack, crankshaft position sensor...if I change the computer will it have to be reprogrammed ? Trying to figure this out ran beautiful as always but all of a sudden wont start and seems to have no spark..please help ! Its a 95 , 1.9L standard transmission
Try resetting the fuel shut of switch.its located on the right rear in the trunk.below the speaker. 95 escort es ... 1995 Ford Escort
My 91 bronco Automatic 4x4 w/ 5.0 engine rough idles when stopped at traffic and cuts off it also tugs as im driving it I changed spark plugs (motorcraft Cooper) changed spark plug wires changed pick up coil, ignition coil,cap & rotor new fuel pump and filter cant buy a bucket please help
Throttle position sensor. ... 1991 Ford Bronco
I have a 98 Ford Expedition EB 4X4 i need to upgrade my front suspension, I cant figure out how do you replace the pittmen arm. It is blocked by the frame cross member & cant get a puller on it to change it with air tools. Any suggestions will be helpful on how to change this part.
You will have to pull the steering gear box that the pitman arm is attached to completely off to change it. Sorry for the bad news. The bolts go through the drivers side of the frame. You will have to take the power steering lines and upper steering ... Ford Expedition
Ignition coil Our 2002 Lanos is pulling a misfire code. I have discovered that the ignition coil is firing 1 and 4 cylinders. Cylinders 2 and 3 seem to have a very weak spark output. 1 and 4 are on the same half of coil, and work fine. 2 and 3 are on other half of coil. I have changed the ignition wires twice to check for bad wires. Problem seems to be coil. I am buying one on Ebay, good price. Hope this resolves issue. Engine dies while driving, no warning. My guess is that as coil heats up und
Hi, the reason for the engine to die when you turn, is because it make more effort while turning ,this is part of the same problem, if you dont have presure some times it can be the pump ,be sure you hear the pump runing when you turn the key ... 2002 Daewoo Lanos
Replace #1 ignition coil on 2002 ford escape
... 2002 Ford Escape