Having problems with your 2006 Chevrolet Uplander ?

How to remove alternator for 2006 uplander? what are the parts to remove in doing this? Is there any video regarding this? I know to rotate engine but that is not enough ...pls help.

\015 I already remove the alternator but i dont know where is the way to go out...some say i have to remove wiper assembly and washer container? im still working on it. Is there any confirmation for that matter? others say i have to remove pulley and belt tensioner? im confused...any help will greatly appreciated thanks in advance..\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2006 Chevrolet Uplander

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove alternator for 2006 uplander? what are the parts to remove in doing this? Is there any video regarding this? I know to rotate engine but that is not enough ...pls help.


... 2006 Chevrolet Uplander

I have a nissan maxima qx v6 24valve automatic..it stated mixing oil and water..so we believe that it burnt the gaskets..so right now we in the process of removing the cylinder heads..but we are stuck with removing the camshafts. Could you help in this regard. does anyone also know where I can download or get an engine manual for the engine please please help


... 1995 Nissan Maxima

Over filled engine oil, slightly above the limit, but when start it smokes??? To remove under engine cover on freelander 2000/w, I removed 2 screws but it still do been removed? pls help


... 2002 Land Rover Freelander

Coolant Leaking My 1991 C-1500 is leaking coolant at a fairly good pace, aprox 1 gal per month or 2. When i go under it i can see that the leak is somewhere up behind the engine. The drips are coming down the backside of the engine and dripping down to the transmition pan (near the front of it). I don't know enough about the anatomy of the engine and cooling system to really know what is up there. Can anyone either help me figure out what is leaking, or provide a diagram or schematic of the engi


Well from what I can tell is that your intake manifold is leaking at the back of the engine, what you can do clean the engine off with some degreaser, put some leak dye in and check it with a ultraviolet light, you could also pressure test the system ... 1991 Chevrolet C1500

I have a 2003 ford focus 2.0. It has a knocking/ticking noise that increases with the rpm's of the engine, I know it has something to do with the rod and lifters; maybe a sucked lifter. I would like to know how to determine what it is for sure and how I can fix it. I must mention I already removed the oil pan and checked the crankshaft and rods there ok. I also tightened every lifter 1/4 turn to see if it would help it made no difference. please help thanks in advance Tim


Hi Tim. It could be so many thing from the timing chain if thats what it has to main bearings in the motor.Stuck valve would not make it knock it would just miss like crazy... Could be a pulley lose on motor. hard to say without hearing it and lookin ... 2003 Ford Focus

I have a c3500 chevy silverado, 7.4 litre engine and the specifications for tuning is not under the hood. I do not know what timing marks should be. Please help. The distributor was removed and repleced to TDC markings not sure what sure what is correct as engine is back firng and runs sluggish. Help


Is this tbi? I'll have to look it up but it should be set at zero degrees with the timing connector unplugged, I think. The timing connector is under the plastic relay cover on the passenger side firewall. It is a single wire plug that the wire is ta ... 1988 Chevrolet K1500

Need to know how to remove the water outlet from 08 charger 2.7 if the intake has to be removed or mabey the radiator the part in question is located at the front of the motor on the top made of plastic with a bleed screw and connected to it is a long steel tube that runs through the vally to the back of engine where it connects to a rubber hose any help would be helpful hank you


... 2008 Dodge Charger

Hyundai i10 Steering not rotating. It seems to be locked. Pls help. The wheels were tilted to other end so, I tried to straighten by turning the steering even before starting the engine. But when I start the engine, i am unable to move the steering and also start the engine.


Faulty Steering?\012It was not until later in the day as I check the Internet for "hyundai i10" "steering locking" that I started to worry once again. I found reviews and comments mentioning that the i10 had problems with its power steerin ... 2010 Hyundai i10 1.2

1995 cutlass supreme head gasked replacement. Chilton's is pretty vauge on details. Never done this before (6 cylinder 3.1). Only on a 4 cylinder 2.2. Chiton's instructs to remove engine struts and to rotate the engine and I don't have and engine hoist. Is it possible to get around this. Also any tips on radiator replacement would be great. Is it possible it could just be the radiator and the head and headgaskets are fine? Your help would be greatly appreciated. Thank you for your time.


Does the car overheat?\015\012If the head gasket is blown:\015\0121. remove the radiator cap & start car (apply parking/emergency brake).\015\0121. When the engine warms to operating temp, there will be "steam" bubbles coming fr ... 1995 Oldsmobile Cutlass Supreme

The engine of the car is running. When I try to shut the enginer off on my 2008 Chevy Cobalt I cannot turn the key to off position. It is stuck. Don't know what to do. I already remove the battery's negative cable but the engine is still running. Please help.


You can remove fuel pump fuse in junction box under hood to kill engine as for key if you look under the steering column near ignition switch you will see a little square plug remove plug and look in hole you will see a little plunger sticking out of ... 2008 Chevrolet Cobalt

I'm trying to remove my tranny and I have the shifter rods hooked up to isand I don't know wat to do to remove then do I pull it out or is there a way to remove it I'm want to pull the engine and tranny out all at the same time can you help


There is a pin going through your shifter rod close to the trans you need a punch and hammer there is also a small clip over it that hides the pin remove that first then you shoud be able to see the long pins ... Honda Civic

2001 Dodge Caravan is not cooling but the air blows good and the heater works.Last month, the "Check Engine" light was on, and the technicians at Dodge did a repair. After that the air didn't cool anymore ( it was working well before that). I don't know if the freon was allowed to escape ( just a theory). Is there a self-help way of gauging if there's a leak in the A/C? If it's lack of freon, can I install it myself? Pls. help!


Yes it is possibly that a schrader srevice valve was left open by a service tech, if you do not want to take it back to get it serviced then you could easily recharge the freon yourself.Any outoparts store will sell you freon in a ready to go can wit ... Dodge Caravan

My 2000 nissian maxima with 106k on it a couple of weeks ago the service engine light came on and then last week the car started to bogg down during acceleration, but once i get over 2000 rpm's and stay at a constant speed it runs fine. the problem is all when you accelerate, it sputters, i don't know if it needs new sparks plugs or something with the engine not getting enough fuel. please help, thanks


The MAF sensor going bad on the 2000 maxima is known to cause the bogging down problems you're having. If you're getting a code for a bad MAF, look into replacing it. ... 2000 Nissan Maxima

2001 nissan maxima - starts for one or two seconds then engine shuts off. I don't know much about cars but it sounds as though the engine isn't getting enough gas. Help please!


... Cars & Trucks

I cannot remove my oil pan on my 97 ford areostar,it seems ther isnt enough room to pull it out,all bolts are removed fromf the pan but i dont know how to get it out.please help


Engine needs to be raised to clear the crank shaft. ... Ford Aerostar

98 pontiac sunfire need to replace lower control arms both how do you access front bolts to remove ,if iremove engine torque strut mount will engine drop or shift ,also how do you get access to nut on same bolt it doesnt look like enough room for a socket ,also any idea size of this nut its originol equipment any help is greatly appricated


... 1995 Pontiac Sunfire

Engin light i got focus 2001, and just sudden yellow engin light come up. is any body know wats the problem is??????? pls help me


Out of the blue my light came on to. The code said was running to lean. I did a tune up. Found out it was well over due. New spark plugs and wires gave it much more power and runs smoother, they had been oxidized, fuel filter was needed also. Runs li ... 2001 Ford Focus

Do you know the correct procedure for removing a power steering pump from a 2001 Ford Taurus OHV engine? Does the pulley have to be removed first in-vehicle? Thanks for your help


Loosen the belt and remove it from the pump pulley. Disconnect the lower hose to drain remaining fluid from the pump. You can tie this hose up or fit a plug into the end of it to stop unnecessary fluid drain. Disconnect the other hose and tie it o ... 2001 Ford Taurus

How do you remove the rack and pinion assembly . There is not enough room to pull it out. Raise the engine ?? Remove the swing arm suspension ? Help, Rick


... 1998 Isuzu Amigo

No brakes Hi I have a 1990 toyota 4runner. I replaced master cylinder,I Bleed all the brake lines But when I push pedal when engines off I have a full pedal. When I start engine pedal goes straight to the floor. I would like to know how to remove booster? Or if there's other things to check first? PLEASE HELP THANK U


1st. Did you bleed the Master cylinder BEFORE you installed the\015\012Master on the booster?\015\012You, need to bleed it on the bench. or you'll pump air into the intire\015\012system.if you tryed to ble ... 1990 Toyota 4Runner

Help with changing spark plugs on a 1998 f-150 5.4L. I've heard it's quite difficult at home and pricy if taken to a shop. Anyone know about this? Story is the engine needs to be dropped on one side????? Or the exhaust manifold removed????? Help!


No the motor does not need to be move at all. Just follow the plug wire to each plug which is located on top of the motor. Pull wire off and slide a spark plug socket with extension down into the head and unbolt. The only one that might give you trou ... Ford F-150

How do you remove clutch housing to replace slave cylinder. Just replaced engine and slave cylinder went out in first 30 miles. And of. Ourselves now every one is going. Why. Didn't you replace it while it was out. I know I can do this but my book is worthless in how to remove clutch. Thanks for any help.


You must take the transmision out to change the slave cylinder, it slides on the transmission shaft.. ... 1987 Ford Bronco II

Any tips to ease the removal of the right rear (as you face the engine) ignition coil. I have the worst time removing it to change plugs. I know I have big hands. Does anyone have any tips that may help me??? Thanks Mack


You must have the Hemi. There is really not an easier way than to unbolt it and slide it out as best as you can. They are a huge pain in the ****. Wouldn't be so bad if you didn't have to do the plugs every 30K. ... 2004 Dodge Ram 1500

My car has been on the diagnostic machine 3 times and it has undocumented code 04122 nobody knows what it refers to. I have a Renault clio dynmique 51 reg. MY engine electronics light comes on all the time and when i come to a stop or slow down and will cut out unless i keep reving my car, the light will go off after reving for about 10 secs at 2500 revs but its eating petrol and the 2 garages dont know anything to tell me apart from the cost of it going on the diagnostic machine. Help pls.


... Renault Sport

How to remove the heater core from a VW Golf MK3 1997 station wagon. There is engine coolant leaking onto the floor of the car. I have bypassed the heater core and eliminated the leak, however obviously there is now no heater. I now want to replace the heater core. I would like to know the procedure for removing the "dash board", taking into account the airbag, air conditioning etc. Thanks for your help Grant


... Cars & Trucks
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.7884 seconds