Having problems with your 2005 Suzuki Verona EX ?

This code came on after driving from Erie to NC P2098

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Code P2098 - Generic Post Catalyst Fuel Trim System Too Lean Bank 2

Could be a stuck lean rear o2 sensor. This sensor is to check catalyst efficiency, sounds like the sensor could be bad, this can be checked by your freindly jeep mechanic or you can check it (rough & ready ) yourself. Its a generic code for all vehicles, and the procedure to solve it is similar en all the cases.

When Monitored: With the engine running in closed loop mode, the ambient/battery temperature above (-7\302\260C)20\302\260F, altitude below 8500 ft and fuel level greater than 15%.

Set Condition: If the PCM multiplies short term compensation by long term adaptive and a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates and a trouble code is stored. Two Trip Fault. Three good trips to turn off the MIL.

Additional details coudl find in this bulletin link TSB_18-028-06 (pdf) or in DTC P2096 (Bank 1)

Hope helps.
Repair Help & Product Troubleshooting for 2005 Suzuki Verona EX

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

This code came on after driving from Erie to NC P2098


Code P2098 - Generic Post Catalyst Fuel Trim System Too Lean Bank 2Could be a stuck lean rear o2 sensor. This sensor is to check catalyst efficiency, sounds like the sensor could be bad, this can be checked by your freindly jeep mechanic ... 2005 Suzuki Verona EX

Terrible miss and loss of power at high speeds after driving for 15 minutes orr so. found to have a error code p301 306, misfire codes, replaced plugs and coil rail. driving action continued and same codes came up. tested fuel pump found it to be weak and shakey so I replaced. ran great, codes returned and repeat of driving action. found an answer (at a differ site) that carbon build up in injectors would send misfire code. replaced injectors. codes came back any idea. Thanks Ralph


The dancing needle is caused by a bad contact at the battery clamps - the battery is left out and the voltage at the alternator varies wildly.\012\012\012That voltage variation is definitely capable of causing all the other problems so clean th ... 2000 Jeep Cherokee

P0505 Code HI, I recently notice my Servine engine light came on. I took it to my Mechanic who had a Diagnostic Test done and came up with the code P0505. He had it cleaned and told me it would be ok. After about 5 days the light came back on. I went back to him, had another Test done and told me i should see a Nissan dealer. Said it is ok to drive . 4 days later the light went off.However today has i was about to drive out i noticed the steering vibratin and all the light came on( Slip, Tcs ,Ab


First make sure that your wires to you iac(idle air control) motor are ok. Also that the pins in the connectors are not damaged. Most likeley you need to replace the iac motor and follow a relearn procedure for the pcm.(powertrain control module) ... 2000 Nissan Maxima

I get a code P0741 for 05 Odyssey EXL (96k miles). Is it safe to drive with this code? Doesn't seem like it's driving any different. Thought was the gas cap when C.E.L came on, but had run on computer and this code came up. Economy mode light not coming on was my only other indication it wasn't a gas cap problem.


The error is means there is an issue with the torque converter on the transmission. It may be stuck. It is safe to drive it but there may be issues with the milage. ... 2005 Honda Odyssey

I have a 2002 chevy blazer 4 wheel drive 4.3 liter. I am having a issue with the 4 wheel drive. I have replaced the acuator motor twice and still keep having a problem. Pulls code P0323 and stays in whatever mode its in and will not change and the service 4 wheel drive light comes on. I cleared the code and changed the driver unit that changes the modes and it worked three times. Then the light came back on with that same code. Cant find any refference to that code anywhere. Any help would be ap


If the problem is the vacuum actuator, 4x4 Posi-Lok replaces the vacuum actuator with a cable. Not a bad upgrade if your replacing the actuator. \015\012http://www.4x4posi-lok.com/app_chevy-s.html ... 2002 Chevrolet Blazer

Code drive 5 . My 2004 trailblazer posted a code "drive 5". It showed the "reduced engine poweer" light, and would not respond to the accelerator pedal. I had been driving in slow traffic. I pulled over, turned the engine off, and restarted it. The reduced engine power light went off, and it drove fine, but the service engine light stayed on. The next day, I filled it with gas, and then the service engine light went off. Then I had the code read and it came up "drive 5".


Thottle body sensor, accelerator pedal sensor, restricted air flow...will all trigger this fault light. Go to your local Autozone, they will run an OBD scan for free, and explain the fault codes to you so the correct repairs can be made.Good lu ... 2004 Chevrolet TrailBlazer

I have a 1997 ford f150 2wheel drive with a trans issue. The trans was rebuild about 2years ago but it only has about 10,000 miles on it. The truck has been running great with no problems. I was on a 10 mile trip to the dump , the truck seemed to lose trams presure it slowed down an then picked back up. I stopped to a store, when I came back out to go the truck would not move? It did throw a code (low voltage)I cleared the code and it has not came back. but the truck still will not drive? It wil


Check transmission lever \015\012position sensor, (on the transmission). It may have failed. \015\012Also, double-check the fluid level.Sound like a TCC (Torque Converter) or solenoids problem, its an internal problem ... 1997 Ford F150 Regular Cab

PO336 code My wife drives a 98 malibu LS 3.1 V6. Last week the check engine light came on and showed a PO336 error code. I had the crankshaft position sensor and the harmonic balancer replace. The code was then cleared. The check engine light came back on after just a few minutes. What else could cause this code?


Cam Sensor ... 1998 Chevrolet Malibu

I heard a pop as I was driving and the engine light came on and subsequently started to flash. I changed the plugs and cleared the codes. Two days later, the light come on and started to flash again, and I changed the coils and cleared the codes. The next day, the light came on flashing again, and I performed a compression test, recording 150 in each cylinder, and cleared the codes again. Two days later, the same codes returned. I am now considering a timing belt job, but I need another opinion.


First before going into it that deep, what year and model? Get the codes instead of just clearing them and let me know. I can advise you on how to proceed without throwing parts at it. ... Chrysler PT Cruiser

1998 dodge ram 4x4 5.2 liter with 115000 miles get a code 1294 and the idle is way to high. Can clear the code 1294 but the idle is still to high. Pulled the battery cables off over night the put them back on and the code 1294 was gone and the idle was back to factory. But after driving a half hour the high idle came back then later the code 1294 came back.


P1294 - Idle Speed Performance Out Of Range - Target Idle Not Reached: means that the\015\012computer is setting a target for the engine to idle at and the engine\015\012cannot do it therefore setting the DTC. Solution start by che ... 1998 Dodge Ram 1500 4WD

2001 honda civic lx - car slipped out of drive and would not accelerate in drive. shifted to lower gear (D3) and it ran fine. next day and ever since it has ran fine in Drive. Check engine light is on with P0730 or p0750 error code. " Gear ration Incorrect" is what the code says. I ould guess it is something with the Transmission since the check engine light came on immediately when the car would not go in drive. What needs to be checked first?


Thanks for choosing FixYa and welcome to the site. I would advise you to have your transmission checked as soon as you can. You might need to check your fluid and change your transmission filter first to see if that helps. But, more then ... Honda Civic

2004 Grand Am GT, 115,000 miles. Service engine light came on. Mechanic checked it yesterday, and the code said "catalytic converter". He checked converter and said it was clear and running fine, so he cleared code and told me to drive it and if it came back on, to let him know. It came back on today. I don't want to have to keep going back and forth to the mechanic to have it re-scanned if the problem can't be fixed.


If a code came up and said catalytic converter. Then you need to replace the catalytic converter. ... 2004 Pontiac Grand Am

U0155 code while driving all the gauges went dead the low fuel light,check engine light and the security light came on. The jeep kept running for about 30 seconds then just died after stoping turned the ignition off then restarted it everything came back on but the check engine light stayed on. Had the parts house read the code it came up u0155 they said the mic,pcm,or the tcm were possible causes just looking for ideas before towing it to the dealer.


The U0155 means "Lost Communication With Instrument Panel Cluster(IPC) Control Module"._________________autoco ... Jeep Wrangler

I need a little help with a P1211 fault code in a 2002 7.3 Powerstroke engine. I drive down the road, and the check engine light comes on. The engine loses power then the smoke pours out. I pull off to the side of the road and shut the engine down and wait about two minutes. Then I restart the engine, the fault code disappears for about ten minutes or when I go above two thousand rpms. When I came back to the shop where I work I put the scan tool on it. The fault code came across with a P1211.A


... Ford F-350

I am helping my daughter with her 2005 Altima 2.5 They were driving it on the highway and the check engine light came on, started missing, loss of power. It was smoking white (not like a burning type of smoke but a vapor type). When at idle in gear engine shakes badly. When they got home (drove for 1 hour that way)I pulled codes, I have a scanner. It came back with bank 1 02 sensor 2. And engine lean code. We changed out the downstream 02 sensor. I cleared the codes and they drove the car to se


First thing you can do to eliminate a possible cause is trade the coil packs between 1&4, and 2&3. Check again and if 1&4 are now dead, then you replace the bad coil pack. You stated that the plugs were wet, but didn't say fro ... 2005 Nissan Altima

2003 intrepid while driving the check engine light came on went to autozone and had it put on diagnostics,trouble codes-p0841,p1776 and p0700, all showed up , once i started the car to return home . The check engine light wasn't on any more.i drove home with no light on the next day it came back on the. Went off I had it retested and no codes were found , I'm very lost and confused on this someone please help the car has 144.234 miles on it.what does the Code - p0841 mean also


... Cars & Trucks

Replaced engine because of spun bearing. Truck ran fine first drive, shifted normal and ran great. Second drive ran rough and didnt have power when starting off, sputtering when driving. 10 codes came up, P0743, P0750, P0755, P1747, P0443, P1451, P0135, P0141, P0155, P1409. Engine is a v10 6.8 liter. Have a list of the codes and what each mean, any help with fixing would be great


... 1999 Ford F250 Regular Cab

2001 bonneville po101 maf code Replaced MAF ,MAP (came apart upon removal, pcv (clooged),intake man & gasket (it was cracked),cleaned TB, Cleared the codes.After driving 15 min had a few stutters and light came back on????? Could the temperature sensor or coolant level trip this code without tripping a temp code? I read that the pcm measures air flow by temp. Does the pcm need to be reflashed? Any suggestions are welcome.


... 2001 Pontiac Bonneville

Vauxhall vivaro 58 2.0 non start. Driving on motorway already done 100+ miles that day glow plug/electrical light came on. I slowed down ready to pull over then engine stop and stop light came on pulled over and turned off now cant start again. Mechanic friend has been and looked cleared codes still nothing and no codes present anymore, fuel us getting to injectors and they have all been changed a few months ago. He says hes baffled as eveything seems to be working and no codes just wont fire cr


... Cars & Trucks

I have a Mercedes s500 2000 with approx. 110k miles. The check engine light came on and the code reader said P0170 (fuel trim malfunction Bank 1) & P0173 (fuel trim malfunction Bank 2). I replaced the MAF with a new OEM Bosch, changed the air filters and reset the codes. The following codes came on within 20 miles of driving and the engine idles rough: P0100 (MAF circuit Malfunction), P0170 (fuel trim malfunction Bank 1), P0173 (fuel trim malfunction Bank 2), P0130 (Oxygen sensor circuit m


Hi!!\015\012\015\012What all this codes have in common is that every single one of them can be caused by a vacuum leak, so carefully check for cracked, loose or disconnected vacuum hoses, wir ... 2000 Mercedes-Benz S-Class

I have a 2007 corvette a6 and a check engine light came on and it was marking the code po777, when i drive the car with the check engine light on , it only drives in the 3rd gear drive. And when i clear the code it droves normally except the transmission it sleeps from 3rd to 4th gear. does anybody else have this problem and may know what to do or how to fix it?


Code p0770 is the shift solenoid (SS) e circuit malfunction Check the following ----Wiring,---shift solenoid---- ECM ( engine control module andTCM Tranny control module ... Cars & Trucks

I have a 1995 7.3liter, 4 door, 2 wheel drive, dually diesel - my problem is: It started cutting out - while doing so the rpms would drop. then it would act normal.. the new problem is.. im cruising down the road and it just dies..completley.. I have to turn the key off and wait to start. no code or lights came on. drove it home.. finally a check engine light came on and the abs light came on, but went away.. truck is too old to find out what codes, so pls help me troubleshoot.. thanxs


Its hard to tell exactly whats going on here because it could be all sorts of thngs but I have had 93 with a 7.3 for a long time. I had a similar problem and found my gas lines were sucking air somewhere in the lines between the two tanks and the inj ... 1995 Ford F350

I have a 1997 dodge grand caravan, while driving on the highway the rpm's jump way up and there is no power, service engine light comes on. pulled over shut the van off and waited approx. 10 min restarted and drove home, light stayed on, had my friend plug in a tester that shows codes and 2 codes came up po700 and po755. engine light has gone out and no problem driving in city so far. Trying to find out what the codes mean?


Code po700 is to tell the ecm and you there is a trans.problem and dtc set in trans.module. po755 is a trans. shift solenoid problem. check trans.fluid level when hot and color of fluid ,dark is not good,burnt smell not good .chrysler has a large tra ... 1997 Dodge Caravan

I have a 2007 suzuki forenza with less than 50,000 miles on it. Yesterday the engine light came on after I went around a curve and I went to have it scanned at a local auto parts store where the code came up as being a transmission sensor. The light went off later that day. Today, the light came back on while I was driving home, and this time the 'D' on my dashboard had an 'x' thru it and started flashing. I immediately pulled over and put it in park. I then put it back in drive (D) and the car


Hi,Check Engine Light is always an Indication that there is a problem with the Car. As you got Transmission Sensor Error, you need to replace or Fix that. It could be a chance that, this light is intermittent. This is a Common Problem in ... 2007 Suzuki Forenza Sedan

I have a 2002 Mazda B-3000 Dual Sport with a check engine lite on...the determinator read code as a misfire on cylinder 6, installed new plugs,wires, coil pack, cleared code & returned to driving vehicle about 2 weeks passed turned on a/c while driving check engine reappeared checked all of the above again as well as compression and vacuum test were all within specs, cleared code again and about a week passed and lite came on again. this is the only DTC that keeps coming up on the OBD 2 , would


... 2007 Mazda B3000
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.2559 seconds