Having problems with your 2005 Pontiac Grand Prix ?

Do i have to do the whole GM drive cycle if i only need the catlyst and evap monitors to read ready

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Repair Help & Product Troubleshooting for 2005 Pontiac Grand Prix

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Do i have to do the whole GM drive cycle if i only need the catlyst and evap monitors to read ready


... 2005 Pontiac Grand Prix

I have driven over 1000 miles. I have done over 100 G M driving cycles all I M monitors read ready, except air and evap monitors which have not proven themselves and read not ready. These monitors should have been ready a long time ago. What is the problem


Some cars are real hard to set. The evap monitor will not run if you start the car with more than 3/4 tank or less than 1/4 tank of fuel from a cold start. \015\012Also you have to cruise at steady throttle for up to 20 minutes on the freeway ... Chevrolet S 10

Failed inspection '01 Mustang GT (4.6 ltr). Catalyst and evap monitors read "Not Ready". Looking for the correct "drive cycle" required to reset the monitors..... Thanks in advance...


... 2001 Ford Mustang

Using my OBD II on 2000 honda prelude trouble codes PO401 & (PO401 pd) all reads MIL on, monitors, 1 INC, EVAP, 7 ready, MISFIRE, FUEL, COMP, CATLYST, 02 sensor, 02 HTR, EGR. Will be cleaning out EGR, BUT do I need to replace my Solenoid? My prelude stalls and ideals out of first gear. (Autotranny). Is this stall caused by these trouble codes? Also with 1 pending code, what do you recomend? I ran car and used OBD II a 2nd time and only change was (0 inc) and 8 (ready).


... Cars & Trucks

When doing a gm driving cycle are the im monitors in a sequence or are they independent of each other? does the evap monitor have to wait for the secondary air to be in a ready mode before the evap monitor can be ready


... 2001 Chevrolet S-10

1998 Honda Civic: 3 sensors reading "Not Ready" when I go to get inspection. O2, Catalyst & Evap...any suggestions on how to solve issue?


... 1998 Honda Civic Coupe

EVAP monitor wont reset to ready after 5 days and 300 miles of driving. Need to pass emission test. AIR pump was replaces 5 days ago. I have been rejected at my last test.


It could be as simple as a faulty gas cap. ... Chevrolet Blazer

My 2003 Toyota Solara will not pass inpection because the EVAP and catalyst monitors won't become ready. I have driven over 400 miles on highway and another 90 around town and have done a Toyota recommened drive cycle. I reset the codes because my coolant temp sensor went bad. Any ideas?


Both of these monitors won't run until the oxygen sensor monitor has run. The oxygen sensor monitor won't run if an Engine Coolant Temperature (ECT) sensor Diagnostic Trouble Code (DTC) is stored. So, did you replace the errant coolant temp sensor? ... Toyota Solara

08 kia rondo need to make ready cAtyls and evap what to do in drive cycle


... Cars & Trucks

I cannot inspect my car because it reads is not ready yet. I used a actron code reader and I had one code that turn out to be the ox sensor by cat. I changed it. When I went back to autozone to get codes again it read none. I went to inspect and still not ready yet. Cannot inspect did not pass emission do I have to do a drive cycle to get computer to read ready? where can I get it.


Basically take the car for a long drive .\015\012Stop off get gas , drive to a shopping center( need a few on/ off starts). Few hard braking , few not so hard braking. reverse when possible . Gotta figure about 30- 50 miles of driving. ... 2002 Mazda Protege

2001BLAZER HAD A PO442 CODE. REPLACE C.C.V. AND FUEL CAP. HAVING A PROBLEM SETTING THE MONITORS FOR SECONDARY AIR AND EVAP. EVAP ST TEST IS DONE BUT EVAP TEST IS SHOWING ABORTED ON THE SCANNER. AFTER REPEATED DRIVE CYCLES MONITORS ARE INCOMPLETE FOR EVAP. AND AIR.


Evap vent valve if you have a scanner with function test go to evap vent valve turn it on and off should hear a clicking noise ... 2001 Chevrolet Blazer

I replaced o2 sensor, bank 1 sensor 1 and all codes pass now except OBD ll says vehicle not ready for emissions. I did one drive cycle but still 3 test incomplete, catalist,Evap sys and O sensor heat


Year, make, model.It will take several "drive cycles" for those test to be complete. Drive it and see what happens. ... Chevrolet S 10

Computer problem 2000 Suzuki Vitara 6 cyl Four Wheel Drive Automatic. I recently replaced the battery on my Girlfriend's Grand Vitara and 3 weeks after took it to for California State inspection and 3 of the emission monitors pull up as not ready. the catalyst ; the evap. ; and the O2 Sens. . we were told to drive it for 100 miles with the fuel tank from 1/2 to 3/4 full and they would reset. doing so we took it back after several hundred miles and the codes are still showing Not Ready ... how do


... 2000 Suzuki Grand Vitara

Catalyst and EVAP monitor shows not ready


... Cars & Trucks

2005 totoya camry drive cycle not ready didnt pass az emission have drove over 300 miles still nothing need help asap please


... Hyundai Sonata

Drive cycle for readiness monitors for a 97 mazda protege


... Mazda Protege

Can't get my 96 chev s-10 to pass inspection due to Not ready codes. I recently change the battery and have driven the veh about 200 miles. Autozone checked and said it was all good but the state inspection machine still shows a couple not ready's. Need to know what defines a drive cycle so I can get the computer to reset to ready?? Or any other suggestions. Thank You


Here is the drive cycle procedure for that vehicle, and let me know if you require any further assistance.\015\012\015\012\015\012Running an OBD-II Drive Cycle\015\012\015\012The purpose of the OBD-II drive cycle ... 1996 Chevrolet S-10 Pickup

I have a Touareg VW, 2004, V8 with active suspension, 4 wheel drive and tyre pressure monitors. These monitors always give me problems as they dont detect the pressure and the defect appears on the dash computer. Two of the 4 sensor modules need replacement and they are expensive. Is there a cheaper solution o is better to disconnect the whole monitoring system altogether? Thx


Your not going to be able to disconnect the monitor system with out causing other problems. I've had this same problem and the only solution was to replace the defective pressure sensor monitors. Have you tried deflating the tire down to a very low p ... Volkswagen Touareg

Not passing DEQ, I need to go through drive cycle, which I've driven 300 miles and nothing. What is the right drive cycle?


... 1997 Kia Sportage

MY VAN DIED ON FRIDAY. IT SEEMED LIKE IT WAS RUNNING OUT OF GAS, BUT I STILL HAD SOME GAS IN TANK. IT TURNS OVER, BUT DOESN'T START. THE CHECK ENGINE LIGHT CAME ON A FEW DAYS AGO. WE ALSO CHECKED THE FUEL PRESSURE ON THE FUEL RAIL. NO PRESSURE. YESTERDAY, WE GOT ONE OF THE ACTRON SCANNERS. IT READ LIKE THIS: we plugged it in and did the scan. it says 0 codes. then Mil says off. IM monitors 5 incorrect.... catalyst evap 02 Sens 02 heat egr im monitors ready. misfire fuel c


Hello mswholesale.To begin I need some details on your Caravan.Year and engine size please. Also do you drive in winter conditions with road salt?I can help you get it running.Thank you.KL ... Dodge Grand Caravan

I have a 07 pont grand prix with code 420 ( cat inefficiant) I change the cat and i still have the same problem. After clearing the codes I can drive it for 5 to 7 days before the code comes back. I check my engine monitors everything show completed except for cat and evap. I recently changed the rear O2 and it now reads about .620 and the FWD readings changes from high to low. Before I changed the rear it was changing from high to low aswell


... 2007 Pontiac Grand Prix

Check engine light rest ....230 miles since and the computer still reads not ready for inspection, how long do i need to drive before the computer is reset and ready?


If the light is on then there is a problem and a code. please recheck. ... 2004 Chevrolet Impala

I have a jeep grand cherokee 1999 model 4.7 v8, I am getting the pcode1698, but it drives great. I failed inspection due to me plugging in a reader and erasing the codes. My failure was due to o2 not ready, and o2 heater not ready. I took it to the shop, and they said that it was a bad alternator, but when they put on a new one it reacted the same, If you unplug the alternator while it is running the computer reads good, but when you plug it in it spses the computer out. I need some real he


... 1999 Jeep Cherokee

Driving code to reset OBD for 2002 chevrolet Monte Carlo SS 3800 Catalytic Converter:I need driving code for resetting cars computer ( OBD)so it will pass smog,There's no problem with the parts it just reads not ready in the results,


Hi, remove the positive terminal cable from the battery using your pliers or wrench.\015\012\015\012\015\012Go to your fuse box in your car, and look at the diagram. Select the fuse that is labeled "ECM" and remove this fuse. Sit the fuse ... Chevrolet Monte Carlo

Drive shaft u joint shot at transmission . Am I reading this right ? 1979 280zx , can't be replaced / need whole drive shaft as a unit? Whats up wit that ? $$$$


... Datsun 210
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.5267 seconds