Having problems with your 2005 Nissan Murano ?

Replacing Murano 2005 seat with 2004-wiring harness different

\015 Trying to use wiring harness from 2005 Murano to fit into a 2004 Murano (the 2005 seat is broken). The wiring pins are different all throughout, though the seat bolts perfectly into car and controlls "look" the same.\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

The new seat probaly has diffarent features mabe one has heated the other doesnt i would get a taredown manual and check the wiring diaogram and see what is shown from one seat to the other
Repair Help & Product Troubleshooting for 2005 Nissan Murano

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing Murano 2005 seat with 2004-wiring harness different


The new seat probaly has diffarent features mabe one has heated the other doesnt i would get a taredown manual and check the wiring diaogram and see what is shown from one seat to the other ... 2005 Nissan Murano

I am trying to replace the factory stereo of my 1998 Toyota Windom and the wiring harness is confusing to say the least. I have looked up wiring diagrams for this car and can't seem to find the one that matches the color of wires that I have.The harness that was in the factory radio has 12 wires split into 4 different groups on 2 rows. The top row starts with a group of 3 wires: 1 black, 1 blue, and 1 brown all with gray dots. The second group has 4 wires: 1 black, 1 red, 1 green, and 1 white al


You need a harness adapter you find it at your local auto parts store ... 1998 Toyota Camry

Service Engine light refuses to go off. Fault Code P0134, states O2 sensor CKT Inactive (Bank 1 Sensor 1). Had already replaced this sensor with a Bosch, mechanic cut off plug from harness and wired in per directions. Rewired in different combinations, light still on. Different opinions for solution: 1. Can only use a Mitsubishi part, Bosch won't work. Buy Mitsubishi, wire it in since plug gone. 2. Still wired incorrectly. Bosch should work. 3. Need Mitsubishi part AND plug. Won't pa


You can use a bosch, but not the universal one. Use the bosch one that is OE design. ... 2001 Mitsubishi Diamante

I swaped seats from 2008 pontiac g6 to my 2006 pontiac g6... connections under seats are different. can i jus change the connectors or would i need to replace the whole airbag wiring harness?


You will need wiring diagrams to do this, we do not have them here at fixya. Please go here to try and find what you need, it is a pay site. ... Cars & Trucks

I need the wiring schematics for the range sensor/neutral safety switch, for a 2003 ford windstar. my brother cut the original harness plug off & replaced it with a different one that has different colored wires, i was having a connection problem & me not knowing he had changed it with a different color code wire plug i disconnected all the wire to fix the connection, when i was going to put it back together i came to find out that the vehicle harness & the plug had different colored wires & now


... Ford Windstar

My defrost fan does not work, how can I find the problem? I traced electric into the control panel. It started with only 1 speed (high) and I replaced a resistor bank and it made no difference. Now there is no fan at any speed. I tested the wiring harness for power and it is reaching the control panel. Where can I test beyond the panel to eliminate the fan as a problem. And, where is the fan. I have no clue.


Dodge systems put power to the blower motor first then ground out through the resistor and switch position.if the resistor block had metal windings in it you may have to replave it again with the blower motor,the resistor has a fusible link built in ... 2002 Chrysler Voyager

I have a 1995 420a swap in a 1996 eclipse rs the wiring was all different for a lot of the sensors and the ecu. I use the 96 harness. I had three of the same looking connectors that went to the ign coil and the camshaft angle position sensor couldn't find the purpose of the last connector once I match the connectors in the right position the car started but ran ruff I put the diagnostic on it and it read code p0340 camshaft sensor circuit 1 malfunction I replaced the sensor and the car hasn't st


... Cars & Trucks

I have a reese brakeman compact trailer brake, also a new tundra with a different harness. What I dont have is the wiring schematics for the brake. There are 4 wires, 1 black 1 blue {both are fatter than the other two} 1 white 1 red. Not sure where to splice tehm to the new harness. Any help would be appreciated.


The best thing to do is get a 12 volt lite tester the one with the pointie end. cut your harness turn on left turn signel. with tester lite grounded tuch the ends of the cut wire from truck strip a small piece of wire covering and attach to your trai ... Toyota Tundra

Hello again Ive tried everting an now I'm at wits end. Need any suggestion for this dilema. Ive replaced a 94 seville sts 4.6 l with a 92 4.9 l seville sts. Icant get it started I replaced the engine harness and pcm/ecm. I've did alittle research from you guys help and though the wording differs alittle the wire are the same in the engine harness to steriing harness connetion whATam I missing or how much would it cost to have it re wired by pros any helpful ideas? thanks caddy daddy despair


I'm guessing the anti theft needs to be programmed for this engine. Call a Caddie dealer service department and ask the service writer if you need to have the PCM/ECM programmed.\015\012\015\012I assume it cranks over but won't start. ... 1994 Cadillac DeVille

Random misfire cylinder 1 code check. one spark plug wire #1 differant wire than rest hard one to get to. can't get #1 plug wire tight enough around think it is the wire, have new gas cap reset code stayed off for a while wire loosend up and check engine light came back on, thought i would replace all wires (Spark) code check it see if it runs better and reset code, you think?


Yes if it is loose can cause a misfire replace the wires as a set ... 1998 Chevrolet Cavalier

1983 Bronco full size with 351w installed. My distributor does not have a vacuum advance on it. It was made that way. It has an old Duraspark 1 box mounted on it. On the harness, someone cut the plug going from the wiring harness to the distributor. Is it okay to cut the plug off the distributor wire and splice it to the wiring harness? Nobody sells replacement plugs to connect the harness to the distributor


Yes they do.\015\012Also,you could cut one off, at salvage yard ... 1983 Ford Bronco

I'm replacing my oxygen sensor in my Tundra. I purchased a Bosch universal sensor. It has 4 wires: 1 black; ; 1 gray; 2 white. My existing harness has 4 wires: 2 black; 1 white; 1 blue. How do I know which wire goes where?


... Toyota Tundra

Have a 2006 Ford F350 6.0L Truck would not stay running, bought a meter, replaced batteries, replaced alternator, found alternator plug was shorting, got new plug at dealer, brought old alternator into dealer to ensure new plug fit, however my truck harness has two wires, #'s 1 and 3, while new plug has 3, #'s 1,2,3, can I use this plug?, if so, what do I do with the third9left over) or middle wire left over.? Any assistance is greatly appreciated. Thanks.


1 & 3 should be all you need. The middle one may be an extra ground or signal for PCM in another model. Colors on the harness are light green/red for pin 1 and orange/light blue for pin 3. OK?\015\012 ... Ford F-350

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

I'm sorry, I confuse with electrical issues very easily, afraid of burning out something. I have a 1956 Chevy 210 4 Door 6 cyl. I bought an intrnal regulator alternator to replace the original system. I've read about 3 wire and 1 wire harnesses. Dumb Q but, how do I wire the 1-wire. Wire gage? Thanks for your help. Steve


Mount the guage to a good ground. The run the one wire to the positive cable. ... 1983 Chevrolet Chevy

I need to replace the wiper motor in my 78 Monte Carlo. The replacement motor is rather expensive and a cross reference brought up several options. The replacement motor I found does not exactly fit and the wiring is slightly different. I've attempted to splice the replacement in and need to know which wire is power and which is control coming from my harness.


... Chevrolet Monte Carlo

Iam replacing the o2 sensor bank 1 sensor 2 on my 2002 chrysler sebring and the replacement wire splice chart does not have the colors that are in the factory harness so how do i find out what color wires to splice with the replacement sensor?


If you have to splice wires you have the wrong part and will likely create more problems than you will fix.The right part will have the correct connector on it and will be "plug and play" no splicing needed. ... Chrysler Sebring

2003 chevy silverado extended cab,2500 hd LT diesel,1 I would like to have the wiring diagram on my truck,2 My heated seats are needing repair,just replace both heating elements in driver side seat work great for a bout 3 months,and now I push button on either side,the light come on and then go out, need wiring diagram and trouble shooting procedure on all problem with heated seats


... 2003 Chevrolet Silverado 2500HD

Elec. windows don't work Windows operated from drivers side door, in varying positions, and sometimes normally! I suspected a broken wire in the harness between the door and the A pillar. I found a broken blk/wht wire coming out of the door but no corolary coming from the A pillar! I do not have a schematic for that harness or color code. The wire seems too small to carry juice to the master switch, (which I cannot find!) I assumed the circuit breaker was blown and replaced it, I cannot find #1


Are power locks working? (I think they are on the same circut) Don't\015\012think there is a fuse, most likely there is a circut breaker (small\015\012metal rectangle plugged into fuse panel Check your manual for location.\015\012There may also be a ... 1995 Jeep Grand Cherokee

I replaced a climate control fan modulator on a 2003 jeep grand cherokee... jeep gave me one with a different wireing harness... i color matched the wires... the fan blows hard but not getting much air through any of the vents...if i turn it on auto for position it blows harder, but not much... when i put it on auto fan, i barely hear the fan... it has a 3 wire harness that i had to splice in... do you have any ideas


The wiring going into the fan motor itself are backwards. The fan isn't spinning the right direction. just switch these wires and it should work better ... Jeep Grand Cherokee

I have a 98 jetta 2.0 k2, recently replaced dist. And ignition wires after car would not fire after running fine previous day. Serviced car and very next day same problem occured only to learn that it may now be the cam/crank sensor. Car has 209000 miles and motor runs fine when starts. 1) was it worth replacing dist. And wires? 2) is this something commonly overlooked by mechanics? 3) is there difference between cam/crank sensor? 4) is this a job that can be done by average do-it-yourself perso


If you just changed the dist and wires the timing may be off or the wires may be in the wrong position. You shouldn't have to replace them again. The cam position sensor and the crank position sensor are different and you should be able to change t ... 1998 Volkswagen Jetta

I have a 95 Taurus sho that was not running right when I bought it. Since I have replaced crank and cam sensors, o2 sensors, knock sensor, wiring harness checked fuel pressure, checked compression, replaced plugs and wires etc. The car will run just fine but when I come to a stop it idled between 1-2 grand back and fourth before just finally stalling. But it starts right back up and usually will idle fine for awhile. Need help!


You did not mention the throttle body or the idle air control valve.The computer controls idle speed by how much air is allowed to enter the intake manifold thru the throttle body.If the idle air control valve is faulty, or there is a vac lea ... Cars & Trucks

I just replaced the fuel pump on my 98 silverado z71 and the harness that came with the new pumps wiring is different. the old harness has four wires colored gray on b, purple and white on a, two black, thicker one on c, smaller one on d. the new has purple, gray, black and white, black. what goes to what? heeeelp!!!


I may not be of much help.According to autozone online, 96-98 model trucks should have - -gray from relay to the pumpblack / white ground for pumppink - black for gauge groundpink to gas gaugeYou should be able to jumper the p ... Chevrolet Cars & Trucks

2003 Saab 9-3 sport sedan, audio is very lacking, was looking to replace the stock amp with the bose amp out of my 98 VW vr6 after taking out of both amps found that the wiring harness's are different (was expecting that) question is.. where can i find a harness that will fit the bose amp (1hm 035 446) already replaced the rear deck speakers with the Bose (from the VR6), just not getting any base from this stock Saab system...NONE,.. any thoughts?


... 2003 Saab 9-3

The fuel gauge is not working as the needle is hanging down almost vertically way past E. It was working fine until the dealer did the following all in one day: 1) did the passenger airbag harness recall @ nc 2) replaced both radiator cooling fan motors -- warranty 3) did transmission & diff service -- nc 4) did checkout & diagnose as to why drivers seat wouldn't move -- nc 5) replaced thermostat & bled cooling system -- charged 6) replaced drive belts -- charged 7) replaced compression rod bush


First, go under the car and make sure that the sending wire from the tank is connected (It will be on top of the tank, look for it going up to the top, and jiggle any wires. If they come loose, bad sign.) Then, go check to see if any fuses are out/ ... 2005 Infiniti G35
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 3.5443 seconds