Having problems with your 2005 Jeep Wrangler ?

I have a 05 Wrangler Sport 4.0. A vacuum line fell off near the intake manifold that leads to the AC. Once it fell off my directional control knob on the dash stopped working about a year ago. I just recently noticed the disconected line and reconnected the line. The directional control now works but the Jeep now wants to surge when stopping and will continue surging once stopped. I have since re-disconnected the line. Please help.

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

There maybe a vacuum accumulator missing in the line between the two points, A plastic part that looks like a small chewing tobacco can with places to attach vac, tubes on top and bottom
Repair Help & Product Troubleshooting for 2005 Jeep Wrangler

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 05 Wrangler Sport 4.0. A vacuum line fell off near the intake manifold that leads to the AC. Once it fell off my directional control knob on the dash stopped working about a year ago. I just recently noticed the disconected line and reconnected the line. The directional control now works but the Jeep now wants to surge when stopping and will continue surging once stopped. I have since re-disconnected the line. Please help.


There maybe a vacuum accumulator missing in the line between the two points, A plastic part that looks like a small chewing tobacco can with places to attach vac, tubes on top and bottom ... 2005 Jeep Wrangler

2001 Merc Marq automatic ac blower motor stopped working. I wired blower directly to battery with a fused switch. This has worked for past 9 months----but, now the compressor stays on when the switch is on. The ac clutch is disengaged when the switch is off, but if you turn the switch on (engine off) the clutch locks in. When the engine is running the compressor evaporator lines frost up unless the ac is on full blast. Do I need a new control panel---or are there fuses or relays that are causing


Check the fuses and blower motor resister first. Some systems don't have resisters. Use blower motor speed control instead.\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012SECTION 412-04: Control Components \015\012\0 ... 2001 Mercury Grand Marquis

The cruise control stopped working and the ac will only blow out of the defrost vents...I read where this might be a vacuum line problem, but I am reading conflicting online info as to where it might be located (the hose) I have a 2003 Jeep Grand Cherokee. Would this hose be on the drivers side or on passenger side under battery?


Do you have the 4.0 inline 6? If you here a sucking or hissing sound you have a vaccumn leak,this wIll cause the air to go to the defrost mode.THE ENGINE WILL RUN FASTER AT IDLE AND BE A BIT ROUGH..Firstly,i would look for a hose off, AT THE INTAKE M ... 2003 Jeep Grand Cherokee

2001 Jeep Wrangler, Starts and runs fine, but stalls at idle especially when warmed up. If I remove the vacuum line from the PCV apature, (it does not have a PCV valve, the jeep seems to idel up to normal and run ok. I have cleaned out the PCV apature, and that vacuum line and that seemed to work ok for about a day and a half, but now it is doing it again. I believe that this may be a vacuum problem but where should I look first? What vacuum lines control the idle speed?


If you cleaned the orfice tube and it got better, it is possible you have lots of gunk in the valve cover that is getting back in there. re-check what you did to see if it's obstructed again. Your idle is controlled by the control valve usually ... Jeep Wrangler

Jeep starts then stops after 1-2 seconds.noticed red circle on control panel,manual says it is the alarm system.?This light continues to flash.After about 15 tries Jeep started and stayed on and red light was gone.Then when home and car was off, tried to start again and same problem.Red light, jeep starts then stops.


Try cycling the key in the door from lock to unlock , see if that helps. ... 2005 Jeep Grand Cherokee

1999 Jeep Grand Cherokee - Heater Core? My Jeep has been fogging up inside, and recently started spewing a fine fine mist inside via the vents with the A/C on. I also noticed a leak last week where coolant was pouring out underneath, however when I went to check it out and add stop-leak if needed, it was completely full of coolant. No room to add stop -leak. I checked for failure codes (dual temp control) and got a 56 = Right Temp Door Travel Too Large. WHAT DOES THIS MEAN? I took it to the gara


Temp fix is to take both heater core hoses and put them together vent door travel is to long/axle on door vnt is stripped out oractuator motor is. ... 1999 Jeep Grand Cherokee

2008 Jeep Commander, both driver and passenger power seat controls stop working. Also noticed that the heated seat controls for both have also stop working. Don't know if it is a fuse or something. Looking for some help. Thanks in advance


Check wiring under drivers seat to memory seat control module as they may have been pulled out or broken if so need to go to dealership, is your vehicle still in warranty if so repair at dealership is free ... 2008 Jeep Commander

Our 2007 Toyota Avalon - the dash vent controls - the nurled disk that you turn left or right to adjust the directional (hidden) vanes for air dispertion. They both (passenger and driver side) have stopped working. We adjust the (vanes) direction (carefully) with a small tool. There was no indication of broken plastic or the like - they just stopped working and i'd like to know what to possible look for - to fix them. Regards Bill


... 2007 Toyota Avalon

I have a 1989 jeep Comanche 2.5L 2wd 5 spd stick i bought it for $300 in running cond.1. on the front left side i replaced the hard line and the soft line going from the porting valve to the caliper on the brake line now even after all that no break fluid comes out of the line at all i have no clue what it would be. 2. i also bleed the system on the front right and both the rear brakes thinking that it might fix the problem, but no, now when i stop the front right skids and both the rear brakes


Okay i had absolutly the same problem in my 89 jeep cheerokee if u have power brakes ... check the pump its high pressure brake fluid on it (under the resivoir tank) first check the relay itsw acually dandiling on mine but heres a tip its the only on ... Jeep Comanche

I have a 1989 jeep Comanche 2.5L 2wd 5 spd stick i bought it for $300 in running cond.1. on the front left side i replaced the hard line and the soft line going from the porting valve to the caliper on the brake line now even after all that no break fluid comes out of the line at all i have no clue what it would be. 2. i also bleed the system on the front right and both the rear brakes thinking that it might fix the problem, but no, now when i stop the front right skids and both the rear brakes


Hi this could be a couple of things, first, the equalizing valve this is the valve that sends the fluid through the brake lines evenly if it is blocked at any point that could cause the problem, other thing could be is the m ... Jeep Comanche

Front power windows 2 issues: (1) passenger window does not work from passenger side button but can be controled from drivers side. While using the drivers side control for this window if the passenger uses their button it will stop the window no matter which direction up or down. (2)Drivers window has issues going up, you have to play with the control button. If the window is all the way down it is diffcult to get it up, if you don't put it all the way down and when ready to close it you must


These are mutiple issues and are unrelated to each other. Sounds like the pass control is shorted somehow or the master control switch(on drivers side) is shorted. As far as the window up/down it sounds like the motor/regulator is going bad or the ... 2004 Chevrolet Malibu Maxx

Jeep was running fine. Shut it off for parking and it would not start. Jeep has 120k miles. Attempted to get computer call out for faults. Message was no ignition present. check computer cable. All other functions appear to be ok. Fuel relay to fuel pump would not energize. Motor turns over fine. Could this be an engine control module problem. This ECM has part # P56041. This is a 2001 Jeep Wrangler with the in-line 6 cyl. Five speed Trans. Help!


The ECM does control fuel delivery as well as fuel injectors. Unplug the cable from the ECM first and check for any corrosion. Spray with electrical contact spray and reset the plug firmly in the ECM. ... 1994 Jeep Grand Cherokee

I have a 2003 Jeep Grand Cherokee 6 cyl. I am getting fault codes P0351,P0352 and P0353 which is defined as #1,#2 and#3 ignition coil circuit and code P0505 JEEP Idle Control System Malfunction and code P1495 JEEP EVAP Leak Detection Pump Solenoid Circuit Condition. The problem I'm having is at times the engine will bog down and lose all power and sometimes just completly quits. I can stop the vechicle and turn the key switch off and start the engine and it will run just fine. I have replac


I would check Cam Position Sensor as is directly related with ignition. Power loss is due to the ECU going on "limp mode" to prevent further damage.I hope this helps! ... 2003 Jeep Grand Cherokee

2003 Jeep Grand Cherokee overland climate control problem. 3 months ago replaced regulator, I noticed the plug end on the wire harness was a little melted on the face from over heating. Bought a new regulator from the dealer for duel climate control and 5 minutes ago coming home it just stopped working. I had the blower on and it just quit working. If I wigle the wire where it connects to the regulator it starts to work. I noticed the wires are very hot at the connection, you can smell faint sen


If the connector was partially burned when you did the work, it will not make good contact. The additional resistance there will cause heating of the wires. Remove each connector from the plug and clean them up. You may need to close them a bit to re ... 2000 Jeep Grand Cherokee

My dash lights all come on, the gages stop working, air conditioner stops, windows wont roll down. One day it works fine, next nothing works. One day it would not start- but only one day. They cleaned a battery wire for the starting problem. Body control module was replaced 3 times and still not working. Any help???? 1999 jeep grand cherokee laredo


Sounds like an electrical problem; look for loose, corroded or kinked/broken wires. The problem is most likely in the dash wiring/connections and seems to be pretty common in jeeps. ... 1999 Jeep Grand Cherokee

2002 Jeep Grand Cherokee was driving fine, stopped to eat and got back in and it would not start. All dashboard warning symbols came on. I checked the manual and it appeared that the engine had been flooded. I did what the manual said for flooding the engine and it started right up. I made another stop and it sat for an hour and then tried to start it again and it would not start. There is a symbol now on the dashboard that looks like a key with a circle around it and the line thru it. I do not


When u turn the key in on poistion do u hear the fuel pump come on it should prime up for three seconds it could be a weak fuel pump leaking down,or look on your key on the sliver part if u have a black piece with a sliver on it that could be wore ou ... 2002 Jeep Grand Cherokee

Rear brakes on 02 jeep liberty lock up and the passenger side doesnt release and grinds real bad all hardware is new the hydrolic lines are new the hydrolic abs control is new the emergency brake cable is replaced the only part that is not from jeep are the pads which r not bevelled like the chrysler pads what could cause them to keep doing this my mechanic is at a loss they r drum brakes


The computer may hav a problem or original parts are needed--search magicmechanic whos an 8 time master ... 2002 Jeep Liberty

Manual side window for 1989 Chrysler Caravan control for opening and closing has probably become partially disconnected from the handle inside. It no longer directly controls the window. I heard and felt something give way. I use it alot because I enter and leave a parkade that requires me to put a card in a slot to open the entrance and exit. Yesterday I couldn't roll down the window, but while I was driving the window fell down and I could roll it back up. Today I failed to roll it down then w


... Chrysler Voyager

I had to take my 2008 F250 6.4 turbo diesel to the dealer because it was loosing power, It had codes poo87,p0088 and p2291. I cleared these codes after I changed the fuel filter, but lose of power issue came back after 10mi of driving. If I stop and shut of the engine, restart it, the full power comes back, after about 10mi. the lose of power issue starts again. Each time this happens the cruise control also stops working. The dealer check and found air in the fuel by install a drain line on top


Check the pcm harness and check pin 16 and 39 to make sure not shorting out. thats the fuel preesure pin and genarator pin. ... 2008 Ford F 250 Super Duty 4WD

I have a 94 Jeep Grand Cherokee Laredo that stalls when slowing down, turning slowly or stopped at a light. Just before it stalls I notice the battery meter drops significantly. The battery is good and the cables are tight. I have had it tested for vacuum leaks. I have replaced the distributor cap and rotor (the contact points were black), the catalytic converter (was busted up inside), and the Idle air control valve. After replacing the Idle air control valve it stalls less often, but still sta


Are you able to pull a trouble code from this vehicle by cycling the key on-off-on-off, then leasve it on and count the flashes given by the engine light in the dash??? ... 1994 Jeep Grand Cherokee

2000 jeep cherokee sport - a/c heat control fan stopped working - the blower resistor looked burned so I replaced it - no change - next I relaced the control module - no change - the two related fuses are fine - any suggestions on what I can check or replace next???


Replace fan motor it caused the resister to go out check fan speed switch on back plug in burned? u also should have a fan relay that could be bad ... 2000 Jeep Grand Cherokee

Hi have a jeep grand cherokee 2001 y reg The heater has stopped working, but blows out cold air? also the crusie control dosent work anymore, but lights up on the dash when u start the jeep, also the button on the autobox dosent work anymore, any help regards martin


Do not rate this answer. I just wanted to let you know with this many issues no one on this is going to be able to help you. You will need wiring diagrams and test procedures. Jeeps are known for having wiring electrical issues and the time its goin ... 2001 Jeep Grand Cherokee

My dash lights all come on, the gages stop working, air conditioner stops, windows wont roll down. One day it works fine, next nothing works. One day it would not start- but only one day. They cleaned a battery wire for the starting problem. Body control module was replaced and still not working. Any help???? 1999 jeep grand cherokee Ltd. Yes, I know that it is an electrical problem! Battery can be disconnected over night and things work good for about 6-8 hours. Turning switch to "on" without s


Try the alternator ... 1999 Jeep Grand Cherokee

Wiper/Washer Motor My washer motor has stopped working. It is mounted within the wiper motor housing. It is controlled with a steering column lever (also cruise control and blinkers). It has low, delays, and a high setting. There are three connector ports on the body of the wiper motor. The lower on consists of 3 wires: Purple, Gray, and White. The mid-connector has 2 wires: Pink and. The upper connector has 2 wires: black w/blue line and gray. When disconnected, the lower connector only has pow


You may have bought a constant wiper motor, rather than one with intermittent settings. It happens. ... 1984 Chevrolet K1500

Jeep 1999 horn, radio controls, and cruise control do not work. Also AirBag light is on but it has been on much longer before the 3 items above stopped working. I understand that it's probably caused by clock-spring? Yes or No? How difficult is it to get to clock-spring and see if connection is bad or replace it all together?


It is the clock spring. Need to remove the steering wheel as it is under it. Disconnect the battery for at least 2 minutes to disarm the airbag. ... 1999 Jeep Grand Cherokee
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.1105 seconds