Having problems with your 2005 GMC Sierra ?

Replace inner tie rod ends on 2005 gmc 1500 . have ev370 moog parts is there a special tool 2 remove the inner rod ends from rack &pinnion. Ihave the tools 4 the outer but the inner looks like a big collar

Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Yes, there is an inner tie rod end wrench, there are a few different types of wrenches available. You should be able to borrow one from one of your local parts stores. (Oreillys, Auto Zone, Napa, etc..)
Repair Help & Product Troubleshooting for 2005 GMC Sierra

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace inner tie rod ends on 2005 gmc 1500 . have ev370 moog parts is there a special tool 2 remove the inner rod ends from rack &pinnion. Ihave the tools 4 the outer but the inner looks like a big collar


Yes, there is an inner tie rod end wrench, there are a few different types of wrenches available. You should be able to borrow one from one of your local parts stores. (Oreillys, Auto Zone, Napa, etc..) ... 2005 GMC Sierra

Had new tires put on my wife's 2005 Grand Caravan today and the mechanic says I need new inner and outer tie rods on the left before he can align the front end (he offered to do it of course, but I'd like to save money if possible). I have the manufacturer's manual, which has a procedure for the outer tie rod - but not the inner tie rod. Plus, none of the big autostore websites list an "inner tie rod," only "tie rod ends" which I assume is another name for outer tie rod. Questions: can I repl


You could replace it at but based on my own with these vehicles most of the time has just been the outer tie rod that was bad. When they don't have a listing for an inner tie rod many times it means the rack needs to be replaced. You can try calling ... 2005 Dodge Grand Caravan

I am replacing my inner and outer tie rod ends on my 96 dodge intrepid. I have the vehicle back together with the exception of attaching the inner tie rod ends to the rack. I am having trouble aligning the holes for the bolts. I am wondering if you have a diagram showing the internal parts to the rack. It appears that there is a spacer that slides back and forth on the rack that is between the tie rods, dust boot and the rack where the bolts attach. Also if that spacer was to fall off, where wou


... 1996 Dodge Intrepid

Recently changed my driver side outer tie rod. Went to get car lined up, they told me my inner tie rod needed replaced. Only got alignment. Stopped at another car shop after alignment n they told me my boots were leaking n I needed a new rack n pinion. Their is a small clicking noise when turning wheel. Like metal on metal. Power steering level is still the same, not losing any....do u think its just the inner tie rod or rack n pinion?


... Cars & Trucks

I am changing tie rods. The replacement for the outer carries a larger threaded bore to fit the inner. I found a matching inner for the outer but the threaded end is too small to fit into the rack. The inner and outer which I took off are smaller in size. please explain


First I have to question if they sold you the correct parts. I have seen this very problem before and the incorrect parts were the issue. Your replacement tie rod should fit your existing inner tie rod shaft like the O.E. one did. I would ... Mazda Tribute

I need torque specs for a 2007 caliber. Balljoint to knockle..... inner tie rod end to rack..... outer tie rod end to knockle... cv shaft nut.. this would be very helpful thank you!


... Dodge Caliber

I ned to know / see the diagram of the 2000 2500HD chevy pu . I need to get the parts for a friend he was told - he needs the pitman arm and idler arm I have not seen the truck yet but would like to see the front end . Nobody lists the pitman arm but I can fine the Idler along with the inner and outer tie rods . They wanted to charge him 650.00 for two parts , I told him I will replace the entire front end and he will still have the money for a front end alingement


Napa online lists two pitman arms for $49, $89 depending upon spline count. As a photo wont give you this info, it may not help...As far as I can see, they list the other components as well but I didn't look at prices. To remove the pitman arm you w ... 2003 Chevrolet Silverado 2500HD

I had 2004 pontiac grand prix 3.8 engine my front end make like metalic noise on when i drive over bumps i repl front control arm biuchings new struts new inner and outer tie rods end new stabilizer links noise is on rigth front only in smal bumps not notice on hig way speed there is a pontiac tech to help me on this one aprentices please


Very difficult without seeing it, but have you replaced the sway bar intermediate bushings yet? These are a common problem.Dave ... Pontiac Grand Prix

Whenever my car hits the rough road its starts making a sound. In a smooth road it runs like a new car, no sound at all. I am positive that the sound is coming from the bottom part of the steering. The sound is like any rod hitting the other rod but there is something in between the sound is not like "cranck". It could be the joint of the steering and the section joining the two wheels. I have checked all portion of suspension, Link Rod, Tie Rod, Rack End Joint, Ball Joint, Jumping Rod etc. Wher


Have you checked the front struts. have a trusted technician inspect the front end. ... 2004 Toyota Corolla

2001 volvo V70 T5 tie rod end replacement. Would like to know how to diagnose and replace the drivers side outer tie rod end. The front end alingment place says it is worn. I notice very little play.


... 2001 Volvo V70

Trying to find out if I need to replace my rack and pinion or if I can replace the seal, or if I can repair the vehicle myself. Took the boot off the rack and didn't see a seal there(or at least don't think I did) there was a pink plastic cup on the end of the inner tie rod that slid right off but wasn't sure if that was the seal or not. Power steering fluid was dripping out of the end of the boot, and when I took the boot off, it poured out all over the place. They sell a replacement seal kit b


Its not as simple as you think !\015\012there are technical issues within the rack that only a specialist can deal with! [internal valves & lock length etc etc]\015\012if you tried you would end up burning the car with frustration!! B ... 2002 Chevrolet TrailBlazer

What are the measurements for the tie rod ends for proper alignment. I am replacing both inner and outer tie rod ends on both sides and I can't go off the originals since the car was so far off alignment to begin with.


When replacing the tie rods ... You need to count the turns to unscrew it off. Then replace it with the same amount of turns ... 1999 Buick Regal

Can i replace a tie rod {inner} on a 94 ford mustang , drivers side without taking off rack and pinion. I need to get a roll pin off the inner tie rod and thats the problem it looks pressed in not set screw like on my replacement part, thanks, Bruce


Real simple, assuming you know how to take the outer tie rods off. You have to take the clip that holds the plastic boot on off, then slide back the plastic boot, and you'll be able to unscrew the whole inner tie rod assembly. The hardest part of the ... 1994 Ford Mustang

Steering my car has a steering problem i bumbed a curb in my 1994 ford probe 2.0 and now the tire is kinda bent in and when i turn it like just drags that tire and none of the rods like the a arm or steering rod or rack and pinion end are broke they all seem to be solid


Solid possibly but you will need to have a wheel alignment down as well as inspection of tie rods and ball joints as well as the rim and tire. just exactly how hard did you hit it ?\015\012\015\012Robert ... 1994 Ford Probe

Replace inner tie rods on 1994 chrysler Town & Country


Here's a link to a basically what your into, except you won't remove rack from vehicle, but it gives you a good idea of what your doing. Where he talks about a jamb nut, also watch for a spring pin, that may be through it, that would have to be remov ... 2002 Chrysler Town & Country

I have a 1999 Ford Explorer XLT, 2 wheel drive,4.0 V-6. I have had this annoying knock from the front end when you drive over small bumps. As time has went by, I have changed the following because they needed to be changed, not because I was trying to cure the knock. Upper Control Arms, Lower Ball Joints, Tie Rod Ends, inner and outer, Anti-Sway bar end connectors. Actually found one of those broken, thought that was the knock, but wasn't. And just recently, replaced the front anti-sway bar bush


Front shocks? Make sure battery is secured . ... 1999 Ford Explorer

Tie rod end replace. outer end in steering knuckle. what does inner end connect to? it goes inside a boot


Connects to the steering rack ... 2004 Cadillac SRX

Daihatsu Sirion 2007. Have noice in steering rack. Sounds like the rod inside is banging on the outer cylinder. Replaced the Rack bush but no change. Not sure if rack is worn out but only done 50,000 KMS. What should be done?


... 2007 Daihatsu Sirion 1.3

1989 toyota supra,driver side outer tie rod,does it turn counter clockwise like any nut or bolt,from the inner rod?any secrets to loosening the rod?


Spray some WD40 on it and let it sit for half an hour it is probably seezed ... 1989 Toyota Supra

How Do I Remove & Replace Worn Inner Tie Rod Ends


Cut band clamp. use tie wrap. Special tool to remove inner tie rod. Autozone or others have them to rent. Must align after replacement ... 2001 Chrysler Town & Country

I think that it is overstearing. It feels like your in 4 wheel drive when turning sharp, but the truck is not in 4 wheel drive (jacked up one side at a time, tires spin freely, also mech. shop checked that). When you watch the truck turn the tires look like it is being pushed not rolling. The problem started when I replaced upper and lower balljoints, tierod ends inner and outer, iddler arm and pitman arm. To replace the pitman arm I had to unbolt steering box to fit my puller. The truck has a 4


If it has a steering damper on it,it maybe the wrong one,if it does not,install one,this will allow it to only steer so far,and that is it,it also stabilizes the steering,some call it a steering stabilizer. ... 1999 GMC Sierra

I think that it is overstearing. It feels like your in 4 wheel drive when turning sharp, but the truck is not in 4 wheel drive (jacked up one side at a time, tires spin freely, also mech. shop checked that). When you watch the truck turn the tires look like it is being pushed not rolling. The problem started when I replaced upper and lower balljoints, tierod ends inner and outer, iddler arm and pitman arm. To replace the pitman arm I had to unbolt steering box to fit my puller. The truck ha


Reading your symptoms seems like it's a cv joint, aka front axle, and not your steering stop. If it's a cv joint it will lock front tire up while turning and almost learch one end of the truck up as it turns. Does this sound like your problem? if ... 1999 GMC Suburban

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it to do myself? I am very mechanically inclined and would like some advice. Thanks - Sam


You will need to rent or borrow in inner tie rod tool but here are the directions.\015\0121. Break the jam nut on inner tie rod to outer loose.\015\0122. Remove nut from outer tie rod attaching it to steering knuckle.\015\0123. Use ... 2004 Chrysler Pacifica

My tires are wearing on the inside like my last car i replaced the outer tie rod ends and ball joints. But on my chrysler 300 2002 model ther looks to be more parts that look like ball joints than just one per side??


Your toe-in is off. Maybe tie rod ends or may just need alignment. If you take it for alignment, they will tell you if any joints are worn out. ... 2002 Chrysler 300M

Driveshaft vibrates shaft from trans to rear wheels, put new u-joints in it but it looks like its the cv in the trans end. will not rotate or (slip yoke), is it a cv joint or is it supposed to remain stationary. you can move the brg cage around inside but the inner is locked to the outer, if it won't swivel than what good is it ? is it supposed to swivel and slip like a cv joint?


... 2003 Ford Escape
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.1507 seconds