Having problems with your 2005 Ford Ranger ?

R/r differential pinion gears

\015 While changing axel seals the pinion gears fell out and I can't get them back in\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

I think its diff out they fit from the top,i am not 100% certain i hope i am wrong
Repair Help & Product Troubleshooting for 2005 Ford Ranger

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to know how to get gears back in differential because i turned the wheel after i took the pin out of the pinion & side gears. the two small pinion gears have numbers on top of them , so i am assuming that they are timed .

They are not timed just line them back up so the pin will go back in. ... 1998 Dodge Ram 1500 4WD

I have a 2002 Mercury Mountaineer AWD where the front pinion gear teeth are gone. Can the front drive shaft be removed to operate the vehicle as rear wheel drive only without damage to the transfer case? If the front differential must be repaired to avoid damage to the transfer case are there instructions available to remove the front differential from the vehicle?

... 2002 Mercury Mountaineer

Have a loud whine from rear differential. gets louder with acceleration stops when not . replaced pinion bearing but still making noise. also the pinion has chewed into the gear housing somehow. how to fix


My 2005 trailblzer v6 front differential (3.42 gear ratio) has now gone out on me for the second time in 2 years. the dealer said it's not a GM problem but i barely use my 4wd and since I replaced it last year I've also replaced the pinion seal, had the dealer do my oil changes so they would check all my fluid levels so they can't say I didn't have fluid in the differential, and now on a 225 mile trip in great weather, it went out on me again - driving in 2wd!! What is causing this and how can

... 2005 Chevrolet TrailBlazer

I have a 99 grand cherokee unlimited v8. I serviced my differentials and did some fwd and rev tight figure 8's afterward to make sure gears were lubricated. After about 5 or six of these the steering got real stiff to the left but not the right, and has been that way since. It is real hard to turn left but sometimes it acts like it gives gets easy until the next time you turn left. Is this the steering gearbox or the rack and pinion. Does it even have a rack and pinion?

Your vehicle has a steering box and from what it seems, there is an internal pressure issue. the other senario is your 4x4 is trying to kick in creating resistance in the steerig. this cause is not an easy fix and will involve the transfer case assem ... Jeep Grand Cherokee

I need to remove the pinion shaft from the spider gears in the front differential on a 2004 dodge ram 1500

... 2004 Dodge Ram 1500

R/r differential pinion gears

I think its diff out they fit from the top,i am not 100% certain i hope i am wrong ... 2005 Ford Ranger

95 tahoe torque specs differential pinion gear

... Chevrolet Tahoe

Ive got a 2006 f150 4x4 stx the differential is making noise bad when you let off the gas ive replaced cluchs spider gears pinion bearing and carrier and bearing and u-joints and it still doing it what could it be

... 2006 Ford F-150

Differential ring gear has 5 teeth broken + bad pinion bearing. whats the best fix, replace with used or repair

Cosidering the age of the vehicle I would replace the whole axle with a used unit. ... 1993 GMC Sierra K1500

I went to have my rear u joints done and the guy bent the pinion ...I couldn't get him to fix the problem and he refused to finish repairing the truck...I need a quick fix for leaking rear differential...its leaking from the cap seal....is there a heavy gear grease I can use as I have to get home asap...its roughly 250 miles.

Wow sorry about that. well there is no grease or quick fix for that, the pinion seal will have to be replaced. with the drive shaft removed you can remove the nut holding the yoke to the pinion gear (rear end) ,pop out the old seal and drive in the n ... Chevrolet Silverado 1500

Ive got a 2006 f150 4x4 stx the differential is making noise bad when you let off the gas ive replaced cluchs spider gears pinion bearing and carrier and bearing and u-joints and it still doing it what could it be

If it only makes noise slowing down it has to be the set of the ring and pinion.A tricky job that has to perfect. ... 2006 Ford F-150

Need help with changing out ring and pinion gears in my 2001 Dodge Ram 2500 need detailed breakdown order of rear differential,is it necessary to remove both axles and while I have it apart what else should I replace ie; seals or bearings need step by step breakdown and reassemble instructions could use diagram thanks...mike weaver

... 2001 Dodge Ram 2500 Truck

Installing pinion gear chevy rear differential how much should it be tightened

It takes special tools to set that. its not a torque reading per se, you tighten it until rotational torque of the pinion shaft is reached. A shop that does read end work may need to help you. ... 1995 Chevrolet C1500

2005 ford ranger very noisey differential sounds like ring gear pinion on pull side noise comes in at 40mphg thru about 50mph

I've come across the same problem with mine it also rattles when coasting. i pulled the diff cover off and found lots of metal shavings inside i had the rear end off the ground so i could spin the wheels. theres a shaft that the planetary gears ride ... 2005 Ford Ranger

After replacing the pinion seal on my wife's 04 f150 fx4 i topped off the fluid using the recommended synthetic 75w140 gear oil. Now on deceleration it sounds like there is a humming coming from the rear diff. Would adding a friction modifier help with this or am i going to have to dig deeper in the differential?

Did you get to correctly tighten the pinion nut to the proper ft pounds of torque level? This nut sets the preload on the pinion bearings, and if this value is not correct, things can go bad quickly.Were you also able to replace the crus ... Cars & Trucks

Need the torque specs for rear differential bearing caps ring gear pinion nut

... 2001 GMC Jimmy

Looking for pinion gear set differential housing - gearbox All oil drained out from dried up seal. Year: 1987 Make: AUDI 4000S ID: wauzzz81zhao(0)15347 Body: 4 Door Cylinders: 4 CYL fueltype: gas Transmission: Automatic Front wheel drive

You can get it here:\015\012\015\012\015\012http://www.autopartsworld.com/audi_parts/4000/differentialpinionseal.htm ... Audi 4000

Pinion gears in rear differential torque specs 95chevy tahoe

... 1995 Chevrolet Tahoe

Gears inside rear end differential fell out

... 1996 Ford F150 Regular Cab

In Aug 05, at 75K miles, my 2000 EB Ford Exp took it to dealer b/c differentail was leaking. They verified the leak was coming from the pinion. Therefore, the complete rear axle, pinion and differential were redone. Now at 133k miles I have a leftrear akle seal leak and the differential has grease around the underside, mostly in the back of it (which it may be the pinion leaking again). Is this normal wear and tear for this vehicle after 58K miles of use from the first service? Thanks.

No they are not suposed to leak period if it is leaking there is some defect ... 2000 Ford Expedition

Need to replace kia ring pinion gear.

... 2006 Kia Sorento 3.5

Can I change gear ratio in 97 GMC Yukon 4X4 Front Differential

... Cars & Trucks

I have a 1996 Ford F350, diesel,5- speed manual trans.The ring and pinion gear are bad in the differential.It has 410 stamped on the ring gear and the tag says 10.25.What are the procedures,torque settings,and adjustments on replacing the ring and pinion

Here is a website that can help you... this is a pretty big job, make sure you have all the tools that you will need. Id also go and buy a Chilton Or Haynes manual for help. Best of luck\015\012\015\012 ... Ford F-350

How do i remove the rear differential gears in a 1999 gmc yukon?

... GMC Yukon XL
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.0980 seconds