Having problems with your 2005 Ford F-150 ?

Rear brakes on 2005 F-150

\015 I am trying to replace the rear brake pads & rotors of my 2005 F-150. I got the caliper & rotor off easy enough But even with a C-clamp I can't seem to push in the brake piston so I can replace the caliper. I've never bled brakes before so I'm a little foggy on the bleed valve location, what it looks like, etc. I've always been the helper in the car pumping the brakes. any help would be appreciated.\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

If you can't compress the piston with reasonable ease...you may have a frozen caliper. It does not "screw in" like GM models. It either presses back into caliper or it doesn't. If it's that hard to press it back in...get a new caliper.
\015\012
\015\012Chris
Repair Help & Product Troubleshooting for 2005 Ford F-150

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I Hanve 1996 GMC 1500 brake pedal goes to floor. New brakes & Calipers in front, 1 new wheel cylinder. 3 New master cylinders,1 new brake booster, Brake line in rear rusted out & replaced. Have checked rubber lines for collasping or bubbling, When Bleeding all wheels lock, Have vacum bled and manual bled. Tried different ideas, do not touch brake until bleeder is open and depress and close bleeder. Tried just about everything, Have adjusted rear brakes out. When truck not running you can


Did you try a brake booster ? ... 1996 GMC Sierra

Brakes (rear) Previous owner (1 month ago) changed the left rear brake cylinder. Pedal felt spongy when I bought the truck, so I bled the right rear, then the left rear brake cylinders. I'm 99.99% positive that I had no air left in those cylinders, and the master cylinder was kept topped-off the whole time. However, now the BRAKE light comes on whenever I press the brake pedal. What did I do wrong, or is there something else I should look at?


I would look at the othe rear wheel cylinder it is most likely leaking ... 1988 Chevrolet C1500

I have a busted rear brake line on my 97 Malibu(V6). Stranded outside city limits. In order to ger into town I need to disconnect rear line at the master cyclinder. Is it the front line for the front brakes and the rear one for rear brakes or the other way around? Please help. I only have 1 small bottle of brake fliud and am just a few clicks from a service station.


Disconnecting the line won't stop the fluid from leaking out. Your best bet would be to use a pair of Vise-Grips and pinch the line off where it is broken. You'll probably have to pinch it a couple of times to get it to stop leaking or only seep a li ... 1997 Chevrolet Malibu

Rear brakes seemm to be sticking on rear of my 2004 murano, 74K highway miles pads changed by dealer at 55k on rear. afterdirving just 5 to 10 miles rearfotors are HOT like calipers stuck or ebrake stuck. Suspect vdc control problem started after a very fast stop with a swerve couple months back. brakes dradding so bad the mpg has went down to 16 :0 mpg rear rotors are becoming warped. Can brake bias be off perportining valve stuck?? VDC freaking out ?? HELP!!!


Take your rear calipers off and lubricate the pistons with bearing grease,move them up and down with your fingers till they move more freely,then remove the dirt from the a.b.s sensor if any with w.d 40. Then check to see if your emergency brake is ... Nissan Murano

I have a 2000 Toyota Tundra V8 4 wheel drive. I just replace new rotor,caliper(old and rusted), and brake pads( front left/right wheel). 1) My friend and I bleed the brake line. I pumped the brake pedal 3 to 4 times till hard. We started from the driver side first, rear passenger side, rear passenger side, and than front passenger side. We did this process twice. The brake is still spongy? 2) When we drive the Tundra and press on the brake we feel a little vibration on the driver side brake?


... 2000 Toyota Tundra

Brakes pressure I have a dodge caravan van 1996 , the problem are the rear brakes, they are not making pression, I have changed the front pads 3 times in 1 year and a half and they continue like new ,I realized of that because I feel the front brakes are working only, the rear brakes are not working properly, the parking brake is working no problem, there are not leaks, ?what do I have to do?


If you jack up the rear of the van and have someone push the pedal do the rear wheels lock? ... 1996 Dodge Grand Caravan

Driver Side Rear Tail lights: running, brake & turn signal do not work. The ground connection is functionind at the lights sockets. The resistance .3 ohms black wire at each light socket to chassis ground. Connector at rear of tail light housing fully functional. .1 ohms across each connection. There is no brake voltage 12 Vdc nor Flasher voltage within the wires at the rear seat. The break (open) condition is some where between the rear seat and possibly the next connect point.rnIs there a d


I suggtes test the "brake light switch", generally, is located in backside of break pedal. With the flasher unit, just replace it.Keep us updated. ... 2004 Pontiac Grand Prix

H2 2004 hummer ...while driving on the freeway the brake lock up on me and I saw a smoke coming out from drive back rear under from tire area. so I try to put it on reverse and then forward ...did not go...waited and pray after 30 minute I try backing up and it move and try going forward it went I didn't reach home so I wait for 1 hour and try it again and I made it home. someone says to let all 4 brakes air out for 1 hour then bleed it good and took it for a drive on freeway and brake lock and


... Cars & Trucks

1997 Montero 4x4 Rear brake calipers are frozen and dragging on the rotors. I need to release the pressure by the bleeder screw so that I can drive to repair shop. Will I still have front brake function if I loosen the bleeder on both rears or only 1 of the rear wheels?


Might be easier and safer to replace the calipers yourself. You would be spilling fluid the whole way to the shop and will eventually empty the reservoir. We can help you DIY--it is not too hard. ... Mitsubishi Montero Sport

Question 1: How do i remove the rear rotor on my 1990 chevy Lumina Euro 3.1? I can't just pull it off. Is it just stuck or do i need to remove some kind of nut keeping it on? If so, where is it located? Question 2: On the front brakes, the brake pad that's controlled by the piston hits the rotor causing the rotor to move and make contact with the outter non piston controled brake pad...Does the rear break pads work the same? If not, how do they work?


Disc brakes work on a clamping principle as you said, on the rear of the lumina the caliper sliders tend to seize causing only the piston side to actuate, you will have to replace these pins and bushings as well, have fun ... Chevrolet Lumina

I need to know the routing of the brake lines at the EHCU. Specifically which brake line connects to which port on the EHCU. There are 3 brake lines in the truck, 1-front right brake, 2-front left brake, 3 the rear brakes. There are 5 brake line ports on the EHCU, 2 of the ports connect to the master cylinder, and the other 3 ports go to a specific wheels brakes for the antilock to work properly. I only need the 3 brake line ports, which brake connects to which port.


... 1999 Ford F150 Regular Cab

My rear brake pads and rotors have worn out in 1 year and the front brake pads are the original and don't look worn at all. My sub has 150K miles


Its possible. There is an equalizer valve that balances pressure to the 4 wheels.Two other possible causes are a problem with the parking brake, or the front rotors and pads are glazed and not providing any friction. ... 2005 Chevrolet Suburban

Recently had front & rear brakes replaced, sensor 1 bank 1, and terrible vibration when going over 60 taken care of. When I got home, I couldn't get rear hatch to engage or open. Could the work I had done be to blame? Thanks


... 2004 Hyundai Santa Fe

Unable to compress brake piston even with bleeder valve open - any tips would be greatly appreciated. The first two (1 -front and 1 - rear) worked just fine. The last one (Right Rear) will not compress.


Sounds like piston has failed in caliper. cost is equal rebuild or replace,i think you would want to replace. ... 2007 Lexus GS 350 AWD Sedan

Brake problem When apply brakes only two side stops ( 1 front and 1 rear ) I have a Nissan Maxima 2000


Do you have a leak? If not try bleeding the ones that don't work. If you get no fluid pressure, replace the master cylinder. ... 2005 Nissan Maxima

1988 plymouth voyager mini van brake warning light stays on. topped off fluid- brake light stayed on. Pedal no longer as "squishy", no signs of brake leak at wheels. Brake master cylinder or brake booster repair needed? 108K miles last brake job was rear only 1 year and 6500 miles ago.


... Plymouth Voyager

Brake Problem My sons 1998 Mazda 626 has had new disc & brake pads fitted to the front of his car & rear disc machined & new pads. Still has Brake problems & is costing him a lot money and the problem is not being fixed. Problem : When the brake is applied he gets a shudder feeling all the time through the brake pedal. His hand brake is adjusted each time it is serviced but after 1 month it is at max position up when pulled on. I hope that you can answer my questions.


Hi im dave\015\012hope i can help \015\012when you had the rear pads applied and the discs turned was there noticeable damage to the disc surface it sounds like your e brake cable is not adjusted properly or perhaps the braided wires insi ... 1998 Mazda 626

I have a 1986 gm motorhome, with a P 3500 (1 ton) chassis, disc brakes all around. I have had issues with the back brakes "sticking" slightly on, resulting in a wicked metatl overheat smell and extreme heat on the rear brake components. The front brakes work and "ride" properly. I have had the whole back end done, (New axle seals, diff seals, calipers, rotors, and pads, done. The problem does not go away. It seems after about twenty minutes of driving, the brakes do not want to fully release on


Sometimes the rubber brake hoses will collapse internally and allow fluid to pass through to the caliper, but won't let the fuild return. The best way to check them is to crack open the hoses where they go into the caliper. If they squirt, then ther ... 1986 Chevrolet Camaro

Problems: Ford focus 2007 model 1. My brake lights stays on while driving without hitting on the breaks, 2. Car wont switch off after removing the key until I let go of the brakes then the car switches off. 3 Everytime I hit on the brakes my front lights switches ON. "The only thing that I can remember changing was the right rear brake light buld"


It sounds like you have a voltage feedback that is providing power to your shift interlock solenoid and your brake lamps are being fed by your daytime running lamp circuits. Check the bulb and make sure that:\0121. It is the CORRECT bulb for ... Ford Focus

89 lesabre limited brake lights won't turn on bulbs and fuses are good 1 brake light in rear window works everytime but not the ones by the running lights. Any ideas?


... 1989 Buick LeSabre

96 Ford Contour - The Classic Rear Brake lights don't work...


No disrespect but....\015\012Check the book and make sure you are using the proper bulbs on all sides. (3957 looks just like 3956 but wont work right) ... 1996 Ford Contour

I have recently dicovered that my 2005 3500(1 ton) 158 SHC that I purchased new in 07/05, has been equipped with the 2500 (3/4 ton) brakes. They have made noise from day one. The rear brakes wore out before the front. The one ton rotors called out for this van do not fit it. The calipers are now leaking and appear to have been cooked. This has to be wrong! can I upgrade to the brake system it should have been equipped with as new? In fact this had to have happened in South Carolina. Thank You, K


Get legal advice!\015\012if its not what you paid for then get him to check the id on the vehicle from the factory as it may have been a special order that was cancelled & sold off !\015\012LUCKY YOU!!!!!\015\012its not uncomman ... 2005 Dodge Sprinter 3500 Standard Roof

Right rear brake light doesn't work, on my 2001 Z-06 Corvette. Took it to the dealership a long time ago for the recall on the steering column. When I got it back the brake light didn't work and the dealership wanted an additional $700 or so to fix it. Then the column key control wouldn't let me drive over 1 mile per hour a few years later and the dealership charged me $700 but still didn't fix the brake light, they said that would be an additional $700.00 So how can i fix this without getting


Check it out. Under the passenger floor panel you will find two relays above the computer box. Pull them. Check them. One of these is to the steering lock bypass which is a $19.70 part at Napa. I went through this for a week and a half and refused to ... 2001 Chevrolet Corvette

Installed previous alloy wheels & drove approx 1 mile then stopped, brakes came on & would not release, very loud noise heard from rear of the car. Finished up switching off engine & switching back on to allow them to release.What has caused this, as illuminated as brake fault, yet brakes are perfect?


Sensors on antilock brakes not picking up new info computer ob. must be reset to new specs on rims ... Land Rover Range Rover Sport

Toyota Cavalier Hello, I live in New Zealand and am having a brake problem with my 96 Toyota Cavalier. Approx 6mths ago I had the rear brakes replaced (pads & cylinders) at local garage . Due to a bad water leak inside car I have had car parked up for 3-4mths. When I moved the car about 1 week ago it was going fine with no binding of brakes. In last couple of days I gave car good wash (incl wheel under wheel arches & mag wheels). I then a couple of days later (yesterday) went to move car &


I know brakes inside and out. I'd love to come down there and fix them for you. I'm unemployed, single male, with nothing else to do.If trans could be arranged, I'd love to fix your brakes. I've always wanted to see Australia. more women than men I'v ... 1996 Pontiac Sunfire
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.8090 seconds