Having problems with your 2005 Chrysler 300 ?

2005 chrysler 300 c

\015 Noise in front end going over bumps\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Front sway bar repair kits needed.
Repair Help & Product Troubleshooting for 2005 Chrysler 300

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

1993 chrysler Fifth Avenue with digital speedometer. The red neon needles for ALL my gauges in the dashboard are not lighted. The needles are either all there or they all go away at the same time. The speedometer says 0 when red needles go away while driving. The odometer also goes away. Sometimes when I start the car, the red needles will be lighted for 1 - 5 minutes but then go away.


... 1993 Chrysler Lebaron

I HAVE A P0300 OBD CODE I DID A COMPRESSION TEST TO ENGINE AND IT PASS THE TEST,I DID CHECK EGR VALVE,CHANGE SPARK PLUGS,IGNITION WIRES, CAP AND ROTOR, I DID CHECK TPS SENSOR MAF SENSOR,FUEL PRESSURE,AND OXIGEN SENSORSI I FOUND THAT ON BANK 1 BOTH SENSORS (UP STREAM & DOWN STREAM )WORKS NORMALY BUT ON BANK 2 THE SENSOR 1 CHANGE FROM 0 TO 600 MILIVOLTS BUT NO CHANGES FROM RICH TO LEAN &SENSOR 2 HAS 0 MILIVOLTS & NO CHANGES FROM RICH TO LEAN SO I SWICHT SENSOR TO TEST THEM FROM BANK 2 TO BANK 1 AN


... 1997 Nissan Pathfinder

Car came in no start-doa. replaced distributor pick up assembly. car ran but hesitated between 50-60 mph. replaced wires plugs,cap,rotor button, air filter. car runs, after about 4-5 min. driving car shuts down no throttle. let sit a few seconds, car starts and repeats problem. before tune-up pcm threw a mis-fire cyl#1,cleared code. no mis-fire code no hesitation just shut down problem with no engine lite. datastream shows cyl#1 0 misfire,cyl#2 0, cyl#4,5 &6 show high misfire rate. not famil


Have you replaced the fuel filter? what is the fuel pressure?, this sounds like a loss of fuel pressure issue, that would account for the miss fire codes, to check fuel pressure look at the top of the engine, in the fuel supply pipe that plugs to the ... Chrysler Cirrus

Ford Focus engine diagram Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V Ford Focus engine diagram - Ford Focus engine Zetec-E 1,8-2,0 l 16V


... 2001 Ford Focus

1996 Chrysler Sebring LXi Coupe V6 -- Check engine light came on and had Auto Zone put the tester on the car. Report shows Oxygen Sensor at Bank 1, Sensor 1 was inoperable, fuel mixture is too lean/rich, misfire code, and a code for the fuel pressure relay. Replaced battery, battery terminals, distributor cap, rotor button, and Oxygen Sensor at Bank 1 Sensor 1. The engine spins over but will not crank. Verified there is spark by pulling one of the plugs. Is there anything specific I should


... 1996 Chrysler Sebring

96 cirrus 2.5. No spark. distributor has 2 wire connectors , 1 has several wires , the other has only 1 wire. When I turn the key , the one that has only 1 wire gets 12 V , but it only lasts for a couple of seconds , then goes down to 0 v . My thinking is that this wire is to energize the coil , and should stay at 12 V to give the coil power to make spark for the Distributor. Can anyone tell me if that is suposed to be a continuos 12 v or not .


Ignition module ... 1996 Chrysler Cirrus

Engine will not start on a 2006 Chrysler Town and Country Limited 3.8, after I cleaned up the Cylinder Heads and replaced all the Fuel Injectors and put everything back together. Now it is throwing off 3 error codes. 1) P0032: Ho2S Heater Control Circuit High, Bank 1, Sensor 1. 2) P0129: Barometric Pressure Too Low. 3) P0700: Transmission control System (MIL Request). Prior to taking the top half of the engine down I had a tapping sound which I thought was do to a bad lifter. After checkin


I guess I will start with the basic statement - as with any no start issue, you have to figure out if it is a spark or fuel problem to proceed.As soon as you crank the engine, the computer runs tests and looks for signals from sensors. So it ... Chrysler Town & Country

Where is oxygen sensor 1 bank 1 n a 2002 chrysler voyager


... 2002 Chrysler Voyager

Went through a car wash and when my car got wet underneath it died. It's kicking over but not getting a spark.. I know 1 spark plug is bad but could that 1 spark plug be the issue? Or What could it be? I have a 2000 Chrysler Cirrus 2.5L 6cyl. I need help like NOW!!! Thanks L!!


You will need to take a look into the hood as this engine has suffered a battery short,as a short term fix,get a can of silacone oil spray and spray it over the electrics of the engine,you will find this will cure the problem if not then you havent s ... 2000 Chrysler Cirrus

98 buick lesabre oil pressure dropped to 0 and engine died. added 1 quart oil, waited 30 minutes, started and drove 5 miles then oil pressure dropped to 0 and engine died. does this sound like a bad oil pump? where is the oil pump and is it hard to change for a "handy" person? thank you.


My sister had the same problem. There are 2 sensors that can cause this when they go bad. One is the oil pressure switch, which is located near the oil filter. When the PCM reads this switch, and gets a low reading, it will automatically kill the eng ... 1998 Buick LeSabre

Dear Expert, I have two very difficult problems with my 1997 Chrysler Van Town & Country and I would REALLY appreciate it if anyone can help: Problem#1 : The Leak detection pump (LDP) keeps failing ? The LDP has been replaced 4 times by a Chrysler dealer in my city ? Petaluma in California. Each time a LDP failed about a week after a new one was replaced ( the dealer keep replacing the LDP pump switch because they already run various tests with the emission system but couldn?t find


Hello, I saw your problem and want to suggest several things which other car makers have on their A/C systems and to comment on the Emission problem.\015\012\015\012First, the Climate controls on some A/C units have their own self-diagnos ... 1997 Chrysler Town & Country

On my girlfriends 1992 Honda Accord we've noticed it has a shuttering problem almost as if lack of gas? It only happens when the car comes to a complete stop. The R.P.M's drop to 0 then bounce from 1 to 0 repeatedly


Sounds like your Idle Air Control Valve may be bad/faulty. ... 1992 Honda Accord

I have the error codes but need help understanding them, and figuring out what I need to replace and where it would be located on a 2005 Chrysler T & C,self test codes are (0016 Bank 1 Sensor A) = Crankshaft/Camshaft mis-align/sync (0138 Bank 1 Sensor 2) = 1/2 O2 sensor short circuit or shorted to voltage. My van is down from 24mpg to 8mpg. I have no accerlation ability as the van surges=jerks,chokes,cuts out both when attempting to accelerate or in park or netrual when pressing on the gas.


Your timing is off and an O2 sensor issue. The timing is your big problem though. Thats whats making your car run bad. Basically you need to realign timing belt. Probably won't need to buy anything unless your timing belt is off. Unless your mechanic ... 2005 Chrysler Town & Country

I have a chrysler 300 limited,the engine light came on, itook it to get it check out and was told that bank 1 & 2 was running lean.so i had the GVR AND Plugs change and the engine light came back on bank 1 still running lean. what else can i do?


... 2005 Chrysler 300

My 2003 nissan sentra has trouble starting. It usually starts and dosen't die by the second or third try. The speedometer will jump from 0 to 1 or 0 to 2 when I am driving and then cut off. Or sometimes the speedometer will jump up and down as the car jerks. When I press on the gas my car makes a coughing sound. I am afraid my car is on the verge of breaking. What do I do?


Good day, try to check the coils spark plugs air filter i hope this tips will help you. ... 2003 Nissan Sentra

On a 2001 chrysler sebring coupe lxi 3.0 where is the O2 "oxygen sensor" physically located, computer says bank1 sensor2. I know Bank 1 is the side where the #1 cylinder is which I "think" is on the firewall side? Someone on this site previously said in another answer it's located on the exhaust manifold at the firewall, sensor 2 is the O2 sensor after the catalytic converter but that is under the car and not at the firewall. There is a sensor on the exhaust manifold at the firewall but it's no


My 2001 chysler sebring lxi 3.0 liter will not start and the starter is brand new ... 2001 Chrysler Sebring

I have a Chrysler Town and Country which shuts off completely while driving. The last time was a 70 MPH and I had to very carefully make my way to the right land and then to the shoulder of the road. The speedometer read "0" and the gas gage read "0". After pulling over the care started right up. This is a dangerous situation. It has been in the dealership three times and checked completely with no results. The first time it happened at city speeds.


Your ignition lock is the most common issue, its the thing you stick your key in. it could be a wire thats shorting out or the whole lock cylender is worn so it could be sending "kill engine signals" at the wrong times, either or, this should be a pr ... 2007 Chrysler Town & Country LX New Cars

Radio my code is 0319 How do you enter the 0 when it initially comes up to 1000 and there is no 0 on the first button, it goes from 1-9?


Using the station buttons , left to right , 1st button is 1000's, 2nd \015\012button 100's, 3rd is 10's, and 4th button 1's, push each button until desired\015\012number from each button , once you have the number in the display it\015\012should unlo ... 1993 Volkswagen Cabriolet

Bank 1 Sensor 1 - Oxygen sensor needs to be replaced. 2001 Chrysler Town and Country 3.3 Is this a job I can do myself? Where can I get an engin schematic?


The sensor you indicate would be on the manifold of the head containing cyl.# 1, top sensor (prior to catalytic conv.) 6 cyl. engine. 4 cylinder would be sensor on exhaust manifold. Confirm sensor failure prior to replacing as chrysler harness conne ... 2001 Chrysler Town & Country

P171 code p171 lean to bank 1. 2003 Infiniti G35. Maf sensor seems to be within range. Only thing I noticed on my scanner is my long term fuel trim was 37.5% and 0 to 3%. Short term fuel trim was 99% and 0. I checked for vacuum leaks with no luck. I'm leaning towards bad O2 sensor or clogged/bad injector.


Yes i would say the same if you are sure there are no vacuum leaks ... Infiniti G35

2005 chrysler grand voyager - three problems - 1 - needs revving to start the car in the morning and 2 battery goes flat a lot and 3 - power cuts out when driving which is really dangerous. Just been charged over £100 by chrysler garage who have not found anything


Catherine223 \015\0121- needs revving to start the car in the morning?\015\012ans- when you start the car, press full the exilator. don't remove the leg from exilator and start the car.\015\012\015\0122- battery goes flat a lo ... 2004 Chrysler Voyager

Error Code reading bank 1 sensor 1 keeps coming on. I had the oxygen sensor replaced but the light keeps coming on. My vehicle is a 2006 Chrysler Pacifica with 99,500 miles on it.


... 2006 Chrysler Pacifica

Propercrankpositionfor correctbelttiming is there a timing mark onthe crank pulley for refrence to line up with a notch on the engine ,besides the flyweel mark? i am puzzled because i have already bent some valves & dont want to repeat my mistake. i have put the #1 piston at TDC, flat with deck ''0'' deck is this right or should it be slightly below ''0'' deck hight and or should the key way be at 12:00 position. please help me P.S, this a 89 honda accord 2.0 carb.3V A20A1 engine


Send me your email address and I will send you the proper timing positions. I can copy them from mitchel and email it.... ... 1989 Honda Accord 4 Door

I have a 1987 Plymouth reliant with an older a/c compressor. I've had the system evacuated and it holds pressure. I've also had it converted to 134 as well. When I add freon to the system, it registers high but when the compressor turns on, the pressure drops to 0. I also have to bypass the high pressure switch to get the compressor to engage. Before it would re-cycle every 1 minure or so. The parts to the a/c system are very old. Intially, the pressure was about 40 lps and now it shows in the 1


First the low side should read 30 and the high should read 230 PSI or up to 275% f. DEPENDING ON THE AIR TEMP. did you change oil for the R134a? if not you will have to empty the dryer and compressor and replace the oil and you will now have to repla ... 1987 Plymouth Reliant

The timing belt on my 2003 Chrysler Sebring LX (93,000 miles) blew out yesterday. The shop I took it to is quoting the price to fix it between $1,200 - $1,800, depending on if any of the valves were also bent when the timing belt went out. Does this sound about standard in cost? I thought it seemed high, but I know it can be steep especially with an Mitsubishi interference engine. Any insight you could provide would be helpful. THANKS!


Ok here is the best way to handle this, replace the timing belt and the water pump if it is driven by the timing belt, also check that that all the idler puley's are ok and the tensioner pulley, start the engine, if it just spins free you have damage ... Chrysler Sebring
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 0.6894 seconds