Having problems with your 2005 Chevrolet Chevrolet Malibu MAXX LS ?

Where are the wing nuts on the rear light assembly?

Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 2005 Chevrolet Chevrolet Malibu MAXX LS

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1991 Chevy Corsica. I attempted to change the tail light bulb for the blinker. I removed the large plastic wing nuts, and the assembly came loose toward the outside of the fender-well, but near the license place area, it was stuck. I feared of breaking the assembly so I am seeking a solution of how to remove the tail light assembly once the plastic wing nuts are removed.


... 1991 Chevrolet Corsica

Where are the wing nuts on the rear light assembly?


... 2005 Chevrolet Chevrolet Malibu MAXX LS

I am trying to replace a turn signal light. Removing the rear tail lamp assembly is giving me troubles. I removed the nuts from the 2 screws in the back of the assembly that attach it to the inside of the trunk, and lifted the tab, and removed the wires attached to the light. But the assembly still doesn't come off. Is there something else I need to remove, or does it just take a lot of force to remove the assembly?


I assume this is a sedan. There may also be a 'locating' pin that must be removed (some sedans).... otherwise pull assembly straight out. ... 2006 Pontiac G6

Trying to replace rear turn signal light by following manual...which I can usually do..however we can't seem to get past removing the 2 screws...it has proven very difficult to find the clips that it says we should be able to slide off to locate access to the tail light . The owner's manual is long winded... 1. Remove the two inboard nuts on the assembly. 2. Pull side assembly rearward to clear studs. 3. Rotate side assembly on the outboard side releasing the upper clip. 4. Slide assembly slight


They are on a rail, after removing the screws it should slide towards you. Since it just wiggles, there are small plastic studs that keep it in place. I you need to pull it towards the front of the car or 90deg out from the front of the van. ... Chevrolet Express

How do you remove the tail light assembly on a 2008 Dodge Avenger? The manual show two wing nuts that must be removed. But actually, only one is a wingnut. The other is some kind of plastic catch that hold a dead pin from the light assembly. How do you remove/release this catch?


... 2008 Dodge Avenger

You replace the brake light assembly for a 2005 Subaru Legacy that is in rear wing spoiler


Here's what I did to replace the brake light assembly for the rear passenger side (this would apply to the drive side as well, but not the brake light on the spoiler) on my 2005 Legacy Sedan:1. Open trunk2. Pull away the interior liner/pa ... 2005 Subaru Legacy

Rear break lights not functioning third is OK and there is no wing nuts in the trunk to remove the tail light to check bulbs....Dont tell me DEALER VISIT any advise?


Use a socket wrench ... 2001 Volvo S80

How to replace the tail light assembly on a 2004 toyota rav 4. Apparently you need to take the interior rear panel off in order to access the nuts that hold the assembly in place. I removed the screws that I could see were holding the panel in place but it's still not budging. There is a tie-down hook on the panel but it doesn't appear to secure the panel in place. How do I get it off?


... 2004 Toyota RAV4

Replace the brake light assembly for a 2005 Subaru Legacy that is in rear wing spoiler


... 2005 Subaru Legacy

I have 2003 2.5 z4, bulb indicator light is on. When making left turn: left rear turn light blinks also 1 red light(left out most bulb lights) when making right turn: right rear turn light blinks only. When making left turn: inside headlamp assembly ,Left front orange bulbs (2) both work When making right turn: inside headlamp assembly, Right front orange bulbs (2) both work. When turn headlights on: inside headlamp assembly: left side ( only orange 1 bulb is working) right (both


Check the socket the bulb goes into ... 2003 BMW Z4

Replacing rear turn signal bulb-- I have the trunk plastic out and the rug up. What size is the nut that retains the light assembly?


10 mm or 11mm or just use a pair of pliers. thats what i always use good luck. ... 2002 Buick LeSabre

How do i take out rear light on a renalt megane i have found the two wing nut fittings but i cannot turn them please help


... 2006 Renault Megane 1.5

I am trying to replace a bulb in the rear tail light of my Chevrolet Lacetti. I have opened the tailgate and removed the two screws which hold in the light assembly but still cannot get the assembly out. I have then peeled back the carpeting inside the trunk area to reveal the back part of where the assembly is located. This is where I get stuck as there does not seem to be any screws or anything. All there is are two plastic things which move when I jiggle the light assembly but does not seem a


Try to turn the two plastic things counterclockwise to loosen them...on many GM tail assemblies these are actually hold-down screws...to re-install insert onto bolt and turn clockwise to securely tighten...you probably did not have to remove the two ... 2005 Chevrolet Aveo

I have a 2004 chev trailblazer XLT V8 and the rear passenger running light does not work. I have tried replacing the rear light assembly and the bulbs.All the other lights work except the running light on that right side. Can I run a wire from the rear right side to the left side and if so what colour of wire do I connect it to or do have any other ideas on to fix the problem


You can run a wire between the two or just take it from the license plate light. they are all on the same circut. Just connect the brown wires. ... Chevrolet TrailBlazer EXT

When I turned on the lights last night to drive home the rear lights did not come on at all. When we hit the brake lights nothing... We turned the lights off and hit brake lights the brake lights come on. Hazzards, blinkers, reverse lights come on. Fuses are good. My thinking is that there is a relay of some kind that went out and if this is the case where would it be located? I know that the passenger rear tail light assembly is going bad and is on order to replace.


... 2004 Jeep Grand Cherokee

Water recently got into the rear light assembly of my 1993 Honda Accord EX. I realized this when my 'brake lamp' warning light came on...I removed the water and cleaned up the sockets. The signal light is working and the running light works when I turn on the headlights, but I can't get the brake lights(passenger side rear, trunk hood or back window)to work on the side that got wet. The only part that doesn't light is the filament that lights when the brakes are applied. Besides drying out every


Did the water short the system out and blow all the bulbs? ... 1993 Honda Accord

1999 Grand Cherokee. Left turn signal does not work at all. All of the 4 ways work except the left rear. I have replaced the left rear bulbs and replaced the entire tail light assembly. Still no good. I checked the voltage at the connector that goes into the tail light assembly-no voltage. I can't find a detailed wiring diagram on the web.


I recomend you look into you signal relay located in your fues box inside the dash left of drivers knee. ... 1999 Jeep Grand Cherokee

How do i remove the rear tail light assembly (without breaking it) so that i can change the brake light? i removed the 2 screws on my wife's 2002 santa fe, but the rear assembly still does not come free.


I have removed the assembly but can't disconnect/reconnect the wiring to replace the entire assembly with a new one. How do I get to the wiring disconnection? ... 2003 Hyundai Santa Fe

1999 GMC Envoy: replaced both GE 3057 lamps in left rear light assembly. Lamps both light. However depressing brake pedal does not initiate brake light. The righ rear brake light does work. The high mount brake light does not. Replaced fuses wit new fuses. Circuit tests all indicate no circuit problems, lose connections, shorts or ground loops. Is the hign mount brake light standard type lamp or is it LED type?


The high mount brake light has its own fuse, so check that first. The high mount bulb is generally a stabdard type (there may be more than one bulb) or you can replace with an LED. As for the left rear bulbs not working when depressing brake pedal, c ... 1999 GMC Jimmy

My 2009 Trailblazer rear wiper assembly broke off, don't ask how cuz my wife will just get angry. All thats there is the 1/2 inch nut and the knurled knob that was embeded in the plastic wiper assembly. I can get the nut off but the knurled knob won't slide off the shaft. My question is, is the wiper assembly suppose to simply slide off the shaft once the nut is removed or do I have to take the whole thing apart from the inside of the liftgate?


The knurled knob is where the wiper arm mounts and should not come off. From the sound of it you need to go to a junk yard or dealer and purchase a new arm. ... 2004 Chevrolet TrailBlazer

2006 CTS right and left rear stop lights do not work. Bulbs are OK. Center high mount stop light works. Rest of rear tail light assembly works. Only the right and left stop lights not working.


Go to the brake pedal siwtch and check voltage there, the center light is not on the same circuit ... 2006 Cadillac CTS

Voltage for rear brake lights at connection .. What are the color codes for the rear brake lights for a 1996 Buick Regal.. How many wires to the connection in the trunk from the tail light assembly to the connection.


... 1996 Buick Regal Olympic Gold

Hyundai Sonata 06 how to remove rear combination Light assembly


... 2006 Hyundai Sonata

93 cutlass supreme 4 dr. left rear turn signal doesnt light. 4 bulbs in assembly all 4 bulbs light when parking or full lights on. when brake depressed upper left bulb doesnt light up. if no lights


Run a new earth wire to the light cluster ,i think this will cure it ... 1993 Oldsmobile Cutlass Supreme

I'm having an unusual problem with a 1990 Geo Prizm. When I step on the brake the brake light comes on in the rear. When I turn on the lights the brake light goes out if I'm holding the brake pedal down. If I turn on the lights and then hit the brake pedal the brake lights will not come. I believe the brake switch is fine because the brake lights come on when I step on the brake with the lights off. I can't find a fautly fuse. I took the light assembly appart and also noticed that there are thre


Make sure you have the right bulbs in the right place...Sometimes they will fit, even though they are not right...Your brake light bulb should be a two filiment bulb...If it is one , then there goes your problem...Now if your bulbs are interchangable ... 1990 Geo Prizm
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.5121 seconds