Having problems with your 2004 Pontiac Grand Am ?

Changing head lamp 04 grand am

\015 How do I get to and change head lamp bulbs on a 2004 Grand Am?\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

You need gloves hands cant touch bulbs .oils from hand causes bulb to blow.to change bulb you raise hood remove head light housing has to be removed before you remove bulb.
Repair Help & Product Troubleshooting for 2004 Pontiac Grand Am

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have 2006 Grand Prix How do I change head lamp?


Caution\015\012Halogen bulbs contain gas under pressure. Handling a bulb improperly\015\012could cause it to shatter into flying glass fragments. To help avoid\015\012personal injury:\015\012\015\012Turn off the lamp switch and allow the bulb t ... 2006 Pontiac Grand Prix

Changing head lamp 04 grand am


You need gloves hands cant touch bulbs .oils from hand causes bulb to blow.to change bulb you raise hood remove head light housing has to be removed before you remove bulb. ... 2004 Pontiac Grand Am

Need to change head lamp - 2002 Jeep Grand Cherokee


It's only 15 minutes work, open the hood and locate a bolt (8 or 9mm) back of the head lamp, remove the bolt and pull the head lamp and if you need to change the bulb, remove the bulb by turning clockwise and replace with the new one. hope it can hel ... 2002 Jeep Grand Cherokee

Changing head lamp in mazda cx7 - 2007 Mazda CX-7 Grand Touring


... 2007 Mazda CX-7 Grand Touring

I wante to change my head lamps - 2001 Pontiac Grand Am SE


Go ahead, change them. ... 2001 Pontiac Grand Am SE

How do you change the head lamp - 2006 Pontiac Grand Prix


Open the hood,and on top of the head light assembley,remove the bolt,you'll need a 10mm socket or wrench,once that is removed,push back on the lense slightly and pull up on the bracket where the bolt was.The pull the light assembly straight out,you m ... 2006 Pontiac Grand Prix

Low beams wont work on 1990 camry changed globes checked fuses, changed head lamp relay . switch seems fine , I was playing with the head lamp realy and it seemed they worked, and the next day they didnt so i have replaced relay still no go and i cant get high beam now unless i pull indicator back towards me to flash high beams , with indicator pushed forward in its traditional constant high beam this function will not work as i did previously either, so no high or low beams now can you help


... 1991 Toyota Camry

Hvac controls I have a 2000 grand am I just bought controls for the ac/heater it all works fine except when I try to change the controls from just head to head and feet or to defrost it will not change just blows from the main vent it will not change to defrost or anything


Most units will use vacuum generated by the engine to help move the dampers. I would bet that might be your culprit. ... Pontiac Grand Am

My 95 grand cherokee is overheating. It only does it while driving, at an idle it will run all day just fine. The guy i bought it from said the head gasket was out. I changed the head gasket and the thermostat already, and i'm about to change the water pump. I'm wondering if there is some common problem with the 4.0 that i just don't know about and if running water in it would, or could, cause that? Also it pops back through the intake when you initially take off, under a load it runs great


The engine is kept cool by a liquid circulating through the engine to a radiator. In the radiator, the liquid is cooled by air passing through the radiator tubes. The coolant is circulated by a rotating water pump driven by the engine crankshaft. The ... 1995 Jeep Grand Cherokee

Head lamp How to change a head lamp


Went to autozone and they did it ... 1996 Ford Probe

Head lamps trouble between driveing and regular lamps when ign. is on bricht /dim are on swit ch to low all are on. dash and column switchs have been changed also relay changed any infro would be greatly appreciated


I am sorry but it is very unclear what u are saying here, are u saying the regular headlights are dim? please elaborate on the problem, also could u please check the spelling of the post before u post the replay. ... 2000 Chevrolet Blazer

Changing 1997 jeep grand cherokee head light assembly


You have to remove the grill and yu will see mounting screws. Consult the haynes manual for a picture. ... 2001 Jeep Grand Cherokee

How do I change the head lights on a 2004 Grand Am.


To reset oil light put the key in on, without turning on the engine, press gas pedal 3 times and u will hear a sound when reset.-------------------------------------------------------------------------------- ... 2004 Pontiac Grand Am

Need to change a head lamp bulb on a clio 2002 and finding it difficult , do i have to remove the hole lamp?


I know some Renaults such as the Megane have an access port within the wheel arch. You might try checking there. If there is one though, then it's likely easier to take the wheel off to get to it. ... Renault Cars & Trucks

Head lights I have an 04 cavalier. My pass side head light went out and the service light came on dash, also on dash it only shows its on high beam. I've changed both head lights and when I did, the pass side lamp stayed very dim and would not swich from high to low beams. If anyone can help it would be much appreciated.


This is fused in the power distribution center. check all related fuses to head lights ... 2004 Chevrolet Cavalier

My 2004 chevy venture van has one low beam head lamp that will not illuminate. The high beam does work. When I went to change the lamp, the wiggeling effect caused the lamp to work intermitently. I bought a new socket thinking it was the problem. This did not fix the problem.


It could only be two things, (1) I realize the connector was replaced but i still suspect a bad connection. (2) was the bulb replaced also, if so then there is a bad ground or power lead leading into the socket. Either at the socket or near the conne ... Chevrolet Venture

How to remove jeep grand cherokee head lamp assembly


Review this guide of the process:- Jeep WJ Service Repair Manual Section 08La Lamps (page 13, fig. 2)- ... 2002 Jeep Grand Cherokee

Head lamp bulb change


I've done this once, so i'll do my best to help you here. You'll need some sort of light you can shine to do this. First you need to unplug the headlight plug from the assembly. Next there will be a rubbery boot you also need to take off, this jus ... 2001 Ford Escape

My Hyundai sonata 1997 model it has got one of its head lamps so dim and dull then i used to think that its the halogen spot lamp itself that needs replacement then i replaced it with a knew one but there was no change it is still very dim and dull please help.


Check to see if you have seperate fuses for each headlight. Some cars do I have seen a blown fuse make a headlight dim. If not check the wiring harness that goes to that headlight to see if any of the ground wires from that harness to body ground ha ... 1997 Hyundai Sonata

How to change the passanger side head light? I know about the pannel but you cannot access the headlight by removing it like you do on the drivers side. I see what looks like a second access with the wires for the lamp I want to change but can not see how to get it to come lose. Thanks for the help


It has a spring clip holding the bulb in place squeeze/pull to remove. ... 2004 Volkswagen Golf

I have a 2002 grand marquis,140 thousand miles...i change my oil on the regular,i take good care of the car..my problem is on my last oil change i noticed a slight tapping noise like the valves where tapping...it got stronger as i punched the gas pedal sumtimes...what i'm trying to find out is do i need a motor or heads...or a knock sensor and what is that?


A knock sensor is basically a resistor and a spring, and what it does is it reduces valve ping. Valve ping is when the fuel is not properly burned and tries to explode before the valve is fully closed and it will make a pinging noise when under load ... 2002 Mercury Grand Marquis

I require instructions to replace the head gasket on a 1999 Jeep Grand Cherokee 4.7 liter V8.Passenger side Cylinder bank.I would appreciate a step by step instruction.Also torque values for the head bolts and any other (rockers) required for this change.Sequence of bolt removal and replacement is required also.I also have to change the radiator.


... Jeep Grand Cherokee

I Just change the head gaskets on my pontiac grand am (1996, 3.1L 6Cyl)and at the time i was pouring the coolant it started to leak it. Ichecked it and found tha the freeze plug was the cause of the leak! it is the one on the back near the dash! I dont know how to get to it i can stick my hand and feel it! but I cant see it!some body knows how to change it? or an easy way to get to it!!! thanx!


The best remedy I can formulate is one that entails using a rubber freeze plug. These are the same diameter as the original. You slip it in the hole (with old plug removed) and tighten the bolt on it. These are good enough for a permanent repair. ... 1996 Pontiac Grand Am

My 1996 Jeep Grand Cherokee is blowing its 20 amp fuse listed as headlamp, park lamp, and head lamp relay. The vehicle will now not start as it continues to blow this fuse. I presume it may be the headlamp rely failing, however, I am at a loss as to why it should blow this fuse and thereby not permit the vehicle to run.


... 1996 Jeep Grand Cherokee

Noise engine noise with oil warning lamp on, This noise sounds like tappet noise, I got the cylinder head cleaned and changed the engine oil.after this we checked the entire oil line cleanes , the oil pressure meter is showing low pressure however the oil pump is ok.still the noise is there, we have cleaned all the oli line in the cylinder head , cam, and casings, I HAVE OPEL CORSA 1.4 2003 MODEL,I AM UNABLE TO FIND THE PRODUCT CATAGORY IN THE LIST BELOW , GIVING FALSE CHEVIRLET ENTRY , PLEASE E


This sounds like bad main and connecting rod bearing they are worn and when they become worn they make noise. Because of excessive clearance between bearing oil pressure drops therefore starving the essential parts of the engine of oil. ... 1998 Chevrolet K1500
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.7705 seconds