Having problems with your 2004 Nissan Sentra ?

Need to locate crank sensor

\015 1.8l\015 Posted / edited by AnonymousUser on : 15-01-2018

Answers :

Below is a picture that should help. Hope it does.....

Repair Help & Product Troubleshooting for 2004 Nissan Sentra

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to know where a crank sensor is located on a 1995 buick century?? And also need to know where the cam sensor is located

Crank sensor is in back of harmanic pulley (crankshaft), and camshaft sensor is on front of timing chain cover. ... 1995 Buick Century

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located

Cam sensor bottom of engine p.s. before you replace part ford has a recall on the cam sensor and might replace free of charge ... 2005 Ford Excursion

2001 Hyundai accent crank position sensor needs replacing. Diagnostics test. The car would stall and then start again about 20 mins later. Can anyone tell me where the sensor is located with some detail??? send picture of location if possible.Thanks

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about y ... 2000 Hyundai Accent

I have a 1997 mitsubishi eclipse gsx and it turns over but wont start need help! its got a new starter on and dont know where the crank sensor and or crank angle sensor is located..

Did you reset the alarm/ immobiliser after the battery was re connected?? ... 1997 Mitsubishi Eclipse

I need a price for parts and labor for a 1996 lincoln Mark Vlll crank shaft sensor, a ham shaft sensor, oil filtering gasket, oil pan gasket and a picture or drawing of each part so I can know where it is located and what it is. I already had a quote and price from one dealer I need to know if we are in the same ball park. Thank You.

Several link for your several parts:- Camshaft ... Lincoln Mark VIII

Need to know where crank sensor is located on 1995 b18c1 gsr

... Acura Cars & Trucks

Need to know where crank sensor is located on 1995 b18c1 gsr

... Acura Cars & Trucks

To replace crank sensor on 2000 galant 4cyl 2.4 ohv where is it located and what parts need to come off to get to it ,or a diagrham,thank you .

... Mitsubishi Galant

Co2 sensor needs to be replaced, where is it located on the car. just replaced the cam shaft sensor and the crank shaft sensor

Check under the car in exhaust pipe looks like a spark plug screwed in pipe. ... 2001 Cadillac DeVille

Car won't start. Need to locate Crank Sensor. Help!

The crank sensor in under the intake manifold on the back side of the engine. its a little tricky to get to- you almost have to be underneath the car, but it's a simple screw out- screw in procedure. ... 2002 Saturn L-Series

Need location of crank sensor for 1997 ford explorer

... Cars & Trucks

Need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter

Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two ... Pontiac Sunfire

I need to locate the fuel pump relay on my mitsubishi chariot grandis. Just redid the engine, it now cranks over but does not take. Getting fuel rail pressure sensor fault. Fuel pump does not pump when ignition is on. Only pumps on crank.

... Cars & Trucks

I have A 2001 jeep Cherokee Sport I know whats wrong with it and i have it at a mechanic. hes just not doing his job and i need the truck to go to work. I need to know the procedure for installin a crank shaft sensor. the old ones off already and i know where its located.

If you know the location and it's already removed, then just reinstall the new one and reconnect it. Do you have any specific problem? ... 2001 Jeep Cherokee

Hi, my name is **** i own a 99 v6 granduer my engine kept cutting out when it reached operating temp i took it to the dealer to be put on the diagnostic machine and they have told me that i need to change both the crankshaft sensor and the crank angle sensor i was reading a reply to somebody who has the same problem could you send me the diagram how to locate and replace them.many thanks ****

It would have been better to get the OE part changed by the dealership as it would have completed the job once you have idenfied with their help.\012However you can try for manuels in the hundai website or ask the friendly dealership ... Hyundai XG300

Push pump You just e-mail me about my problem with 1995 chev. I need some more info on this problem. I need to know were the crank sensor and the electric jumper is located. Also dose the push pump come on when the key is turned?

\015\012Disconnect the negative battery cable.\015\012Detach the sensor harness connector at the sensor.\015\012Unfasten\015\012the retaining bolt, then remove the sensor from the front ... 1995 Chevrolet C/K 3500

Where is the sensor located for the crank on a 1999 4.7. I need to replace the sensor

Cranksensor is located on the passengers side of the block. Not in bell housing on a 4.7. ... 1999 Jeep Cherokee

Location and difficulty of replacing crank sensor on 92 park avenue? auto stalls out, farts, back fires? replaced water pump hose connecter that screws into block from top of water pump outlet? took out thermostat (looked a little burnt), still dies whe driven less than five minutes...with or without thermostat? spark plugs and wires seemed to be fine? Need some advice, before i blow the motor? thanks gregg..........PS can auto zone test these sensors and do they have to be on the vehicle while

This could be one of many issues (or more than one!). When you say runs for 5 minutes, does it just stall? overheats? Probably not the crank sensor since when they go they go and engine will not run. If you can get it to Autozone or borow a diagno ... 1992 Buick Park Avenue

Ive replaced the cam shaft sensor but need to see about fixing the crank shaft sensor and do not know where its located

The crank shaft sensor is located on the front of the engine under the timing cover. In order to replace it you will need to remove the timing belt. ... Chrysler LHS

I have a 1992 chevy cavalier and i need a diagram on the location of the crank system sensor, i need to replace it, please help.

Haynes Manual at library or local dealer can copy it for you ... 1992 Chevrolet Cavalier

I got a 2004 kia sorento the crank sensor needs to be replaced where is that sensor located at?

The crank sensor is located inside timing belt cover at crank pulley. ... 2004 Kia Sorento

I need a diagram to find location of crank sensor for 2006 nissan altima. i am trying to replace the sensor.

... 2006 Nissan Altima

Need location of crank shaft sensor on vauxhall vectra 1800 16v

... Cars & Trucks

I need to know where the crank sensor is located on my mazda 6 2005 2.3

... Cars & Trucks

Can you show me on screen exactly the location of the knock sensor part #22060-30P00 8D SENSOR A and Oxygen sensor part # 22690-40U06 8D, HEATED O,(FR,RH), sensor assy-02, #1 bank, located before the catalytic converter for the '97 Maxima 6 Cyl 3.0L,distributor less ignition. I need to replace these parts, would like to do it myself if possible but can't locate them on my engine or pipe. Do I need special tools to do this?

Gpk722000: the knock sensor is located under the intake manifold.\015\012If you are standing in front of the car, look to the right of the oil filler cap and go more to the center of the valve cover. Now, if you look carefully belo ... 1997 Nissan Maxima
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 2.3017 seconds