Having problems with your 2004 Nissan Murano ?

What's the torque setting on a nissan murano tie rod?

\015 Have changed the right front tie rod end on a 2004 Nissan Murano and would like to know the torque setting.\015 Posted / edited by AnonymousUser on : 22-01-2018

Answers :

Repair Help & Product Troubleshooting for 2004 Nissan Murano

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What's the torque setting on a nissan murano tie rod?


... 2004 Nissan Murano

What are the torque specs for nissan murano 2003 tie rod end


... 2003 Nissan Murano

What is the torque setting for the tie rod end nuts on a 1986 nissan micra?


... Nissan Rogue

I need the torque setting for a 1998 toyota sienna van inner tie rod?


... 1998 Toyota Sienna

TORQUE SETTING ON FRONT WHEEL BEARING NUT ON 2006 nissan murano


... 2006 Pontiac Torrent

Nissan murano abs & awd inoperative after replacment of rf wheel bearing & r//l outer tie rod ends.


Almost cetainly broke wheel speed sensor during bearing replacement.easy to forget to remove it before removing bearing assy. ... 2004 Nissan Murano

Torque settings for 98 chevy suburban 4 wheel drive outer tie rod end


... Cars & Trucks

Hi I have an 04 nissan sentra 150 xxx miles and I had problems with suspension. Car would shake on the hwy when iwould drive past 65 mph. My tires were wearing uneven as well. So I decided to get a new set of tires, changed all 4 struts as well, got an alignment and was told that next time I do an alignment I would need to replace my driver side tie rod end. The same day I got the alignment, I drove the car on the hwy again and I was able to drive past 65 this time but I noticed that the car wo


... 2004 Nissan Sentra

Tie rod torque - 2002 Nissan Maxima


... 2002 Nissan Maxima

What are the torque setting for ball joints and tie rods for 98 dodge durango?


... 1998 Dodge Durango

Whats the torque specs for rod caps on nissan sentra gxe 1.8 engine


... Cars & Trucks

1997 nissan sentra inner tie rod torque specs


... 2008 Ford Taurus X

I drive a 2007 Nissan Murano. I noticed today a knocking noise which seems to be coming from the front right tire. When I am driving straight is when I notice it, I can hear it more at the car accelerates and when I slow down/coast to stop. Does anyone know what may cause this. I just had the tie-rod ends replaced not to long ago. Thanks.


... Cars & Trucks

Torque spec for 2002 altima tie rod end - Altima Nissan Cars & Trucks


... Nissan Altima

What are the torque settings for the outer tie rod ends and sway bar ends for a 2001 S60 volvo 2.4T


... Volvo S60

Whats the sequence as far as setting tappets on the Nissan Champ 1400cc motor which is the push rod type motor.


Your pretty close \015\012which ever cylinder you have rocking when timing mark at top dead centre also aligned you adjust the opposite plus one rocker from each of the other middle cylinders. these will be the loose ones. then turn engine over ... 1997 Nissan Pickup

I need the torque specs for a 2000 nissan maxima connecting rod torque specs


... Nissan Maxima

Can i replace a tie rod {inner} on a 94 ford mustang , drivers side without taking off rack and pinion. I need to get a roll pin off the inner tie rod and thats the problem it looks pressed in not set screw like on my replacement part, thanks, Bruce


Real simple, assuming you know how to take the outer tie rods off. You have to take the clip that holds the plastic boot on off, then slide back the plastic boot, and you'll be able to unscrew the whole inner tie rod assembly. The hardest part of the ... 1994 Ford Mustang

Nissan murano 2005 i can,t set clock time - Murano Nissan Cars & Trucks


... Nissan Murano

How to set clock on nissan murano - 2010 Nissan Murano


... 2010 Nissan Murano

Torque settings whats the torque settings for the head bolts ?


Usualy taken up in three stages 30,50,65 foot punds dont use the small torque wrench because that is in inch pounds. Cheers ... 2004 Honda Odyssey

PLEASE COULD YOU SEND ME THE TORQUE SETTINGS FOR A NISSAN 1400 BAKKIE, THE HEAD HAS JUST BEEN DONE AND MY HUSBAND WANTS TO PUT IT BACK BUT DOESN'T HAVE THE TORQUE SETTINGS.


First you need to know what year is it and engine size in liters 2.0, 3.0,2.2 etc.and then you can get what you look for, ... Nissan Pickup

Hi need to know the torque setting for con rod big end bearing and crankshaft bearing torque setting please


... 2000 Ford Focus

I need torque specs for a 2007 caliber. Balljoint to knockle..... inner tie rod end to rack..... outer tie rod end to knockle... cv shaft nut.. this would be very helpful thank you!


... Dodge Caliber

I have a 1990 nissan maxima with an inner tie rod problem. I have everything apart with the inner tie rod in sight but i can't seem to get to it with a wrench to break it loose without taking the whole engine and transmission apart. PLEASE HELP!!!


Hello. If you haven't done so already, jack up the front and remove the wheel on the side you are working on. Sometimes it is helpful to turn the steering wheel to get the tie rod end nut to an open space. Of course always use jack stands and wheel c ... Nissan Maxima
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.carrestorationshop.com || Terms of Use || Contact || Privacy Policy
Load time: 1.5796 seconds